Boser HS-2622 User manual

HS-2622
VIA V4 Eden processor
Embedded Engine Board
•CompactFlash•CRT/LVDS/DVI•
•Dual LAN•Audio•SATA•
•RS-232/422/485•6 USB2.0•
•WDT•H/W Monitor•

Copyright Disclaimers
The accuracy of contents in this manual has passed through checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e., electronic, mechanical, photocopying, recording)
of this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or modify the contents of
this document without any notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2008 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.0, May 19, 2009

Table of Contents
Chapter 1 General Description ..................................1
1.1 Specifications ........................................................................ 2
1.2 Board Dimensions................................................................. 3
Chapter 2 Unpacking ..................................................5
2.1 Opening the Delivery Package............................................. 5
2.2 Inspection............................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ................................................................. 7
3.2 Board Layout ......................................................................... 8
3.3 Jumper List ............................................................................ 9
3.4 Connector List ....................................................................... 9
3.5 Configuring the CPU ............................................................. 9
3.6 System Memory ..................................................................... 9
3.7 VGA Controller .................................................................... 10
3.8 Serial ATA Port .................................................................... 12
3.9 Serial Port Connectors ....................................................... 12
3.10 Ethernet Connector............................................................. 13
3.11 USB Port............................................................................... 13
3.12 CMOS Data Clear................................................................. 14
3.13 Power and Fan Connectors................................................ 14
3.14 Keyboard/Mouse Connectors ............................................ 15
3.15 System Front Panel Control ............................................... 16
3.16 BIOS Write Protect .............................................................. 16
3.17 Audio Connectors ............................................................... 16

Chapter 4 Award BIOS Setup ................................. 17
4.1 Starting Setup...................................................................... 17
4.2 Using Setup ......................................................................... 18
4.3 Main Menu............................................................................ 19
4.4 Standard CMOS Features................................................... 20
4.5 Advanced BIOS Features ................................................... 21
4.6 Advanced Chipset Features............................................... 22
4.7 Integrated Peripherals ........................................................ 25
4.8 Power Management Setup ................................................. 28
4.9 PnP/PCI Configurations...................................................... 29
4.10 PC Health Status ................................................................. 30

Declaration of Conformity -- CE Mark
BOSER Technology hereby acknowledges that compliance testing in
accordance with applicable standards of the EU’s EMC Directive,
89/336/EEC, was successfully completed on a sample of the equipment
identified below:
Equipment Class: Information Technology Equipment
Product Model Series: HS-2622
This Product Complies With: EN55022: Class A for Radiated emissions
EN50082-2: Heavy Industrial EMC Immunity
We, the undersigned, hereby declare that the equipment specified above
conforms to the above directives and standards.
Manufacturer:
BOSER TECHNOLOGY CO., LTD.

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
 Do not remove boards or integrated circuits from their anti-static packaging
until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This helps to discharge any static
electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR clip
of the strap to the end of the shielded wire lead from a grounded object.
Please wear and connect the strap before handle the HS-2622 to ensure
harmlessly discharge any static electricity through the strap.
 Please use an anti-static pad when putting down any components or parts or
tools outside the computer. You may also use an anti-static bag instead of
the pad. Please inquire from your local supplier for additional assistance in
finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTIONS.

1
Chapter 1
General Description
The HS-2622 is designed in a 3.5” embedded form factor to fit the low
power VIA V4 bus Eden processor onboard, to meet today’s
demanding pace, and to keep complete compatibility with hardware
and software function supported. The onboard devices support VIA
Eden 1GHz processor, integrated graphics and dual Ethernet
controllers. It’s beneficial to build up a fanless system integrator.
This board hosts VIA V4 Eden processor with 400MHz FSB in
combination with the VIA CX700M chipset with an integrated graphic
memory controller up to 128MB and supports dual view function with
VGA/LVDS & VGA/DVI with one SO-DIMM up to 1GB DDR2
400/533MHz, enhanced onboard one PCI-IDE interface supporting 2
drives of Ultra ATA synchronous mode feature, an onboard Super I/O
chipset for two serial ports: one RS-232 serial port interface and one
RS-232/422/485 pin header. Besides, integrated RealTek ALC883
AC97 codec, Hi-speed USB2.0 x 6 ports offering greater bandwidth
over USB1.1, one 6-pin Mini DIN connector for PS/2 mouse and
keyboard, and one +12V 4-pin DC in power connector designed to
support ATX power function.
Targeted for key embedded applications such as Point of Sales (POS),
car media centers, industrial PCs (IPC) and ultra compact, low power
desktop systems such as thin clients that require flat panels support,
the digital display using LVDS/DVI interface. All of these features make
HS-2622 excellent in all-in-one applications.

2
1.1 Specifications
 CPU: VIA V4 Eden 1.0GHz processor
 Front Side Bus: 400MHz FSB
 Memory: 1 x 200-pin SO-DIMM socket support DDR2 400/533 SDRAM,
max. up to 1GB memory
 Chipset: VIA CX700M
 I/O Chipset: Winbond W83697HG
 SSD: 1 x CompactFlash socket with ejector at I/O side (shared Master
IDE)
 VGA: VIA CX700M with 128MB shared main memory supports CRT
display up to 2048 x 1536
 LVDS Panel: 1 x dual channel or 2 x single channel with 24-bit LVDS,
resolution up to 1600 x 1200
 DVI: 1 x 30-pin DVI shared with LVDS interface, resolution up to 1600 x
1200
 Ethernet: Dual VIA VT6106S 10/100 Based LAN
 Audio: RealTek ALC883 7.1+2CH audio codec
 Storage: 1 x parallel ATA IDE port with UDMA 33 support by 44-pin IDE
connector, 2 x Serial ATA 150 ports
 MIO:
Internal: 1 x RS-232/422/485, 2 x USB2.0
External: 1 x VGA, 1 x Audio jack, 2 x RJ-45, 1 x RS-232, 4 x USB2.0, 1
x KB & Mouse
 BIOS: Award BIOS with 4Mb Flash ROM
 Watchdog Timer: Reset: 1sec.~255min. and 1sec. or 1min./step
 Power Requirement: [email protected] (with onboard VIA V4 Bus 1GHz &
1GB DDR2 SDRAM)
 Power Type: DC in 12V 4-pin power connector/ATX function
 Operating Temperature: 0~+60°C (32~140°F)
 Operating Humidity: 0%~90% relative humidity, non-condensing
 Board Size: 144.78(L) x 101.6(W) mm

3
1.2 Board Dimensions

4
This page is the blank page.

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-2622 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-2622 delivery package
contains the following items:
 HS-2622 Board x 1
 Utility CD Disk x 1
 Cables Package x 1
 Jumper Bag x 1
 User’s Manual

6
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-2622. This chapter also contains information related to
jumper settings of switch, and watchdog timer selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (JP1 short 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.

8
3.2 Board Layout

9
3.3 Jumper List
Jumper Default Setting Setting Page
JP1 Clear CMOS: Normal Operation Short 1-2 14
JP2 COM2 Use RS-232 or RS-422/485 Select:
RS-232 Short 13-14 12
JP3 BIOS Write Protect: Unabled Short 1-2 16
JP4 AT/ATX Power Function Select: ATX Open 14
3.4 Connector List
Connector Definition Page
CN1 PS/2 6-pin Mini DIN 15
CN2 3-pin Power In Connector 14
CN3 External Audio Connector 16
CN4 15-pin CRT & COM 1 Connector 10/12
CN5/CN6 External USB & RJ-45 Port 13
CN7 ATX power connector 14
CN8 CD In from CD-ROM 16
CN9 Inverter Power Connector 10
CN10 LVDS/DVI Connector 10
CN11 IDE Connector ----
CN12 COM 2 Connector (2x7 header) 12
CN13 System Front Panel Control 16
CN14 System Fan Connector 14
CN15 Auxiliary Power Connector 14
CN16 Internal USB2.0 Port 13
DIMM1 SO-DDRII Socket 9
SATA1/SATA2 Serial ATA Port 12
U15 CompactFlash Connector ----
3.5 Configuring the CPU
The HS-2622 embedded with VIA V4 Eden 1.0GHz processor. User
don’t need to adjust the frequently and check speed of CPU.
3.6 System Memory
The HS-2622 provides one SO-DDRII socket at locations DIMM1. The
maximum capacity of the onboard memory is 1GB.

10
3.7 VGA Controller
The HS-2622 provides two connection methods of a VGA device.
CN4(VGA) offers an internal 15-pin CRT connector and CN10 is the
LVDS interface connectors onboard reserved for flat panel installation.
 CN9: Inverter Power Connector
PIN Description
1 GND
2 +3.3V
3 BL On/Off Control
4 BL Brightness Adjustment
5 +12V
 CN4(VGA): 15-pin CRT Connector
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 +5V 10 GND
11 N/C 12 DCC_DATA
13 HSYNC 14 VSYNC
15 DCC_CLK

11
 CN10: LVDS Connector
PIN Description PIN Description
1 A_DATA0-/DVI_TLC- 2 B_DATA0-
3 A_DATA0+/DVI_TLC+ 4 B_DATA0+
5 A_DATA1-/DVI_TDC0- 6 B_DATA1-
7 A_DATA1+/DVI_TDC0+ 8 B_DATA1+
9 A_DATA2-/DVI_TDC1- 10 B_DATA2-
11 A_DATA2+/DVI_TDC1+ 12 B_DATA2+
13 A_DATA3- 14 B_DATA3-
15 A_DATA3+ 16 B_DATA3+
17 GND 18 GND
19 A_CLK-/DVI_TDC2- 20 B_CLK-
21 A_CLK+/DVI_TDC2+ 22 B_CLK+
23 LVDS_VCC 24 LVDS_VCC
25 +5V(DVI) 26 +5V(DVI)
27 DVI_CLK 28 LDDC_CLKL
31 DVI_DATA 30 LDDC_DATA_L
Signal Type Description
LDDC_CLKL I/O EDID support for flat panel display
LDDC_DATAL I/O EDID support for flat panel display
DVI_TCL+/- O DVI Clock Output: These pins provide the differential
clock outputs to the DVI interface corresponding a data
on TDC(0:2) outputs
DVI_TDC0+/- O DVI Data Channel 0 Output: These pins provide the
DVI differential output for data channel 0 (Blue)
DVI_TDC1+/- O DVI Data Channel 1 Output: These pins provide the
DVI differential output for data channel 1 (Green)
DVO_TDC2+/- O DVI Data Channel 2 Output: These pins provide the
DVI differential output for data channel 2 (Red)
DVI_CLK
DVI_DATA
I/O Serial Port (SMBus) Clock and Data. The SPCLK
signals are the clocks for serial data transfer. The SPD
signals are the data signals used for serial data
transfer. SPCLK1/SPD1 is typically used for DVI
monitor communications.

12
3.8 Serial ATA Port
These SATA ports support Serial ATA 150. Each SATA port can only
support one SATA device.
NOTE: With most storage devices, there is a power cable that you need attach
to a power source (power supply)
3.9 Serial Port Connectors
The HS-2622 offers NS16C550 compatible UARTs with Read/
Receive 16-byte FIFO serial ports and four internal 10-pin headers
and one RS-422/485 connector.
 CN4(COM 1): COM 1 Connector (DB9)
PIN Description PIN Description
1 Data Carrier Detect 2 Received Data
3 Transmit Data 4 Data Terminal Ready
5 GND 6 Data Set Ready
7 Request To Send 8 Clear to Send
9 Ring Indicator 10 Not Used
 CN12: COM 2 Connector (2x7 header)
PIN Description PIN Description
1 DCD 2 DSR
3 RxD 4 RTS
5 TxD 6 CTS
7 DTR 8 RI
9 GND 10 GND
11 TxD+ 12 TxD-
13 RxD+ 14 RxD-
NOTE: The enclosed serial port cable for COM 2 with different functions as
below.

13
 JP2: COM 2 use RS-232 or RS-422/485 Select
Options Settings
RS-232 (default) Short 13-14
RS-422 Short 1-2, 3-4, 7-8, 11-12
RS-485 Short 1-2, 3-4, 5-6, 9-10, 11-12
3.10 Ethernet Connector
The HS-2622 provides two RJ-45 connectors for 10/100 Based LAN.
Please refer to the following for its pin information.
When installs OS, this driver namely can automatically install. User
does not need to renewal.
 CN5/CN6: RJ-45 Connector
PIN Description PIN Description
1 TX+ 5 N/C
2 TX- 6 RX-
3 RX+ 7 N/C
4 N/C 8 N/C
3.11 USB Port
The HS-2622 provides three ports, at location CN5/CN6/CN16, for six
USB2.0 ports.
 CN5/CN6: Internal USB2.0 Port
PIN Description PIN Description
1 +5V(fused) 5 +5V(fused)
2 USBP0-/2- 6 USBP1-/3-
3 USBP0+/P2+ 7 USBP1+/3+
4 GND 8 GND

14
 CN16: External USB2.0 Port
PIN Description PIN Description
1 +5V 6 DATA_5+
2 +5V 7 GND
3 DATA_4- 8 GND
4 DATA_4+ 9 N/C
5 DATA_5- 10 N/C
NOTE: This mainboard provides 1 USB header on the board allowing for 2
additional USB ports. To make use of these headers, you must attach
a USB bracket/cable with USB ports (some models will come
packaged with a USB 4-port bracket-cable). The optionally packaged
bracket will have two connectors that you can connect to the headers
(CN16). The other end (bracket containing the USB ports) is attached
to the computer casing.
NOTE: If you are using a USB2.0 device with Windows 2000/XP, you will
need to install the USB2.0 driver from the Microsoft® website. If you
are using Service Pack 1 (ort later) for Windows® XP, and using
Service Pack 4 (or later) for Windows® 2000, you will not have to
install the driver.
3.12 CMOS Data Clear
The HS-2622 has a Clear CMOS jumper on JP1.
 JP1: Clear CMOS
Options Settings
Normal Operation (default) Short 1-2
Clear CMOS Short 2-3
3.13 Power and Fan Connectors
HS-2622 provides one 4-pin power in at CN16. Connector FN1
onboard HS-2622 is a 3-pin fan power connector.
 CN2: Power Connector
PIN Description
1 5VSB
2 GND
3 Power On