Boser HS-7001 User manual

HS-7001
PGA 478 Pentium®4
Industrial Single Board Computer
•Full-size•Giga LAN•CRT•ATA/33/66/100•
•Dual LAN•Audio•4COM•PC/104•IrDA•
•USB2.0•DOC•WDT•H/W Monitor•
•PICMG Bus Industrial Single Board computer•
StockCheck.com

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review
before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is
not liable for any infringements of patents or other rights resulting from its use. The
manufacturer will not be responsible for any direct, indirect, special, incidental
or consequential damages arising from the use of this product or
documentation, even if advised of the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation,
and storage of any form and means (i.e., electronic, mechanical, photocopying,
recording) of this document, in whole or partly, is prohibited, unless granted
permission by BOSER Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the
contents of this document without due notice. BOSER Technology Co., Ltd.
assumes no responsibility for any errors or omissions that may appear in this
manual, nor does it make any commitment to update the information contained
herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2004 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.2, November 24, 2004
StockCheck.com

Table of Contents
Chapter 1 General Description..................................1
1.1 Major Features................................................................. 2
1.2 Specifications .................................................................. 2
1.3 Board Dimensions........................................................... 4
Chapter 2 Unpacking .................................................5
2.1 Opening the Delivery Package....................................... 5
2.2 Inspection......................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ........................................................... 7
3.2 Board Layout ................................................................... 8
3.3 Jumper List ...................................................................... 9
3.4 Connector List ................................................................. 9
3.5 Configuring the CPU ..................................................... 10
3.6 System Memory ............................................................. 10
3.7 DiskOnChipAddress Setting .................................... 10
3.8 VGA Controller............................................................... 13
3.9 PCI E-IDE Drive Connector........................................... 14
3.10 Floppy Disk Drive Connector ....................................... 16
3.11 Serial Port Connectors ................................................. 17
3.12 IrDA Connector .............................................................. 18
3.13 Parallel Connector......................................................... 19
3.14 Ethernet Connector....................................................... 19
3.15 USB Connector.............................................................. 20
3.16 CMOS Data Clear ........................................................... 20
3.17 Power and Fan Connectors.......................................... 21
3.18 Keyboard Connectors................................................... 23
3.19 PS/2 Mouse Connector ................................................. 23
3.20 System Front Panel Connectors.................................. 23
3.21 External Speaker ........................................................... 24
3.22 Watchdog Timer ............................................................ 25
3.23 Audio Connectors ......................................................... 26
3.24 PC/104 Connectors ....................................................... 27
StockCheck.com

Chapter 4 Award BIOS Setup .................................30
4.1 Starting Setup ................................................................ 30
4.2 Using Setup.................................................................... 31
4.3 Main Menu ...................................................................... 32
4.4 Standard CMOS Features ............................................. 33
4.5 Advanced BIOS Features ............................................. 34
4.6 Advanced Chipset Features ......................................... 35
4.7 Integrated Peripherals .................................................. 36
4.8 Power Management Setup ........................................... 37
4.9 PnP/PCI Configurations................................................ 38
4.10 PC Health Status............................................................ 39
4.11 Frequency/Voltage Control........................................... 39
4.12 Load Fail-Safe Defaults................................................. 40
4.13 Load Optimized Defaults .............................................. 41
4.14 Set Supervisor/User Password.................................... 42
4.15 Save & Exit Setup.......................................................... 43
4.16 Exit Without Saving....................................................... 44
Chapter 5 Software Utilities ....................................46
5.1 IDE Driver Installation ................................................... 46
5.2 VGA Driver Installation ................................................. 53
5.3 LAN Driver Installation.................................................. 62
5.4 Audio Driver Installation ............................................... 74
5.5 USB2.0 Driver Installation ............................................ 76
StockCheck.com

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity.
To avoid damaging chips from electrostatic discharge, observe the
following precautions:
 Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion
of the system unit chassis for a few seconds. This helps to discharge any
static electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR
clip of the strap to the end of the shielded wire lead from a grounded
object. Please wear and connect the strap before handle the HS-7001 to
ensure harmlessly discharge any static electricity through the strap.
 Please use an anti-static pad when putting down any components or
parts or tools outside the computer. You may also use an anti-static bag
instead of the pad. Please inquire from your local supplier for additional
assistance in finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTION.
StockCheck.com

StockCheck.com

1
Chapter 1
General Description
The HS-7001 is an Intel®82845GV/82801DB chipset-based board
designed for PICMG Bus PGA 478 Intel®Pentium®4 up to 2.8GHz
CPU compatibility. These features combine and make the HS-7001 an
ideal all-in-one industrial single board computer. Additional features
include an enhanced I/O with CRT, Dual LAN, audio and 4 COM ports
interface.
Its onboard ATA/33/66/100 to IDE drive interface architecture allows
the HS-7001 to support data transfers of 33, 66 or 100MB/sec. to each
IDE drive connection. Designed with the Intel® 82845GV/82801DB
core logic chipset, the board supports all PGA 478 Pentium®4 CPU
series operating up to 2.8GHz. The CRT display controller is Intel
82845GV with 1MB or 8MB memory supporting CRT display up to
1920 x 1200 x 32-bit at 60Hz.
System memory is also sufficient with the two DDR sockets that can
support up to 2GB(DDR-333). While using 533MHz FSB CPU, it could
support DDR-333, but using 400MHz FSB CPU, it only could support
DDR-266.
Additional onboard connectors include an advanced USB and IrDA
ports providing faster data transmission, a DOS-compatible
DiskOnChipsocket with a maximum capacity of 288MB, and two
external RJ-45 or two internal 5x2 connectors for one 100/1000 and
one 10/100 OR two 10/100 Base-TX Ethernet use.
StockCheck.com

2
1.1 Major Features
The HS-7001 comes with the following features:
 PGA 478 for Intel®Pentium®4 up to 2.8GHz CPU
 Intel®82845GV/82801DB system chipset
 Two DDR sockets with a max. capacity of 2GB
 Winbond W83627 super I/O chipset x 2
 Fast PCI ATA/33/66/100 IDE controller
 Four RS-232 serial ports
 PC/104 Bus connector
 Intel®82845GV CRT display controller
 Intel®82540EM 10/100 Based (or Intel®82551 10/100 Based) and Intel®
82562 10/100 Based LAN
 AC97 3D audio controller
 DiskOnChipTM socket supporting memory sizes of up to 288MB
 Supports USB2.0, two USB connectors
 Supports Hardware Monitor function
1.2 Specifications

CPU: PGA 478 for Intel®Pentium®4 up to 2.8GHz CPU (400MHz FSB up
to 2.4GHz, 533MHz FSB up to 2.8GHz)
 Bus Interface: PICMG Bus

Memory: Two DDR sockets supporting up to 2GB(DDR-333)

Chipset: Intel®82845GV/82801DB

I/O Chipset: Winbond W83627 x 2

VGA: Intel®82845GV with 1MB or 8MB supporting CRT display up to 1920
x 1200 x 32-bit at 60Hz
StockCheck.com

3

IDE: Four IDE disk drives supporting ATA/33/66/100 and with transfer rates
of up to 33/66/100MB/sec.
 FDD: Supports up to two floppy disk drives

Parallel: One enhanced bi-directional parallel port supporting
SPP/ECP/EPP

LAN: One Intel®82540EM 100/1000 Based(or one Intel®82551 10/100
Based) and one Intel®82562 10/100 Based LAN
 Audio: AC97 3D audio controller
 Serial Port: 16C550 UART-compatible RS-232 x 4 serial ports with 16-byte
FIFO

PC/104: PC/104 connector for 8-bit x 2clock ISA Bus

IrDA: One IrDA TX/RX header

USB: Supports USB2.0, two USB connectors

Keyboard: PS/2 6-pin Mini DIN or 5-pin connector

Mouse: PS/2 6-pin Mini DIN

DiskOnChipTM:DiskOnChipTM socket supporting memory sizes of up to
288MB
 BIOS: Award PnP Flash BIOS
 Watchdog Timer: Software program time-out intervals from 1~256sec.

CMOS: Battery backup

Power Connector: One 4-pin and one 20-pin ATX power connector

Temperature: 0~60°C (operating)

Hardware Monitor: Winbond W83627

Board Size: 33.6 x 12.2 cm
StockCheck.com

4
1.3 Board Dimensions
StockCheck.com

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-7001 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. ExAwardne all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-7001 delivery package
contains the following items:

HS-7001 Board x 1
 Utility CD Disk x 1

Cables Package x 1
 Cooling Fan x 1

Jumper Bag x 1
 User’s Manual
StockCheck.com

6
Cables Package
NO. Description
1 Floppy flat cable x 1
2 ATA/100 IDE flat cable x 2
3 5-pin ATX power cable x 1
4 Two USB split type cable with bracket x 1
5 Parallel port flat cable with bracket x 1
6 MIC/Audio 8-pin cable x 1
7 Two COM flat cable with bracket x 2
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
StockCheck.com

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-7001. This chapter also contains information related to
jumper settings of switch, watchdog timer, and the DiskOnChip
address selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (Set JP2 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.
4. Make sure your power supply is using for P4 only. One of 4-pin
connector is for +12V lead which should connect to PW1
connector of HS-7001.
StockCheck.com

8
3.2 Board Layout
StockCheck.com

9
3.3 Jumper List
Jumper Default Setting Setting Page
JP1 Clock Speed Select: CPU Select 1-2 Short 10
JP2 Clear CMOS: Normal Operation 1-2 Short 19
JP4 DiskOnChip Address Select: D000H~D1FFH 3-4, 7-8 Short 10
3.4 Connector List
Connector Definition Page
CD1 CD Analog Input Connector 25
CD2 Line In Analog Input Connector 25
COM1 COM1 Connector (DB9) 16
CN1 Green LED Connector 22
CN2 Reset Connector 22
CN3 HDD LED Connector 22
CN4 2-pin ATX Power On/Off Switch 20
CN5 Keylock Connector 22
CN6 5-pin Keyboard Connector 22
CN7 Speaker Connector 23
CN11 / CN12 / CN8 / CN9 COM1~COM4 Connector (5x2 header) 16
CN10 MIC In/Line Out Connector 25
CN13 5-pin ATX Power Connector 20
DM1 / DM2 188-pin DDR Socket 10
FDC1 Floppy Connector 15
FN1 / FN2 / FN3 Chassis/CPU/System Fan 20
IDE1 / IDE2 IDE Connectors 13
IR1 IrDA Connector 17
KB1 PS/2 6-pin Mini DIN Keyboard Connector 22
LN1A / LN1B Dual RJ-45 Connector 19
LPT1 Parallel Connector 18
MS1 PS/2 6-pin Mini DIN Mouse Connector 22
PC1 PC/104 64-pin Connector 26
PC2 PC104 40-pin Connector 26
PW1 4-pin ATX Power Connector 20
PW2 20-pin ATX Power Connector 20
USB1 USB 2.0 Connector 19
VGA1 CRT Connector 12
WOL1 Wake On LAN Connector 18
StockCheck.com

10
3.5 Configuring the CPU
The HS-7001 offers the convenience in CPU installation with its
auto-detect feature. After installing a new microprocessor onboard, the
HS-7001 automatically identifies the frequency and clock speed of the
installed microprocessor chip, thereby eliminating the need for user to
do additional CPU configuration or hardware settings related to it.
 JP1: Clock Speed Select
Setting Description
1-2 Short (default) CPU Auto Detect
2-3 Short 100MHz
Empty 133MHz
3.6 System Memory
The HS-7001 provides two DDR sockets at locations DM1 and DM2.
The maximum capacity of the onboard memory is 2GB. While using
533MHz FSB CPU, it could support DDR-333, but using 400MHz FSB
CPU, it only could support DDR-266.
3.7 DiskOnChipAddress Setting
The DiskOnChipfunction allows the system to boot or operate
without a FDD or a HDD. DiskOnChipmodules may be formatted as
drive C or A. With DiskOnChip, user may also execute DOS
commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and
DISKCOMP etc.
The DiskOnChipmodule socket is location on U15 on the HS-7001.
Jumper JP4 assigns the starting memory address of the installed
module. If you have another memory device that has a similar memory
capacity with that of the DOC in your system, please set both at
different memory address mapping to avoid the mapping area conflicts.
Failing to do so will not make the HS-7001 and the additional memory
device function properly.
 JP4: DiskOnChipAddress Select
Address JP4
CC00H-CDFFH 1-2, 9-10 Short
D000H-D1FFH (default) 3-4, 7-8 Short
D400H-D5FFH 3-4, 9-10 Short
D800H-D9FFH 5-6, 7-8 Short
StockCheck.com

11
DC00H-DDFFH 5-6, 9-10 Short
StockCheck.com

12
3.7.1 Installing DiskOnChipModules
When installing a DiskOnChipmodule onto your board, please take
note of the following:
1. Orient yourself properly with the location of the DiskOnChip
socket. Try to locate the pin 1 location on your socket. Pin
numbers are usually printed on either the component side or the
solder side of your board.
2. Locate the Pin 1 location on your DiskOnChipmodule. More
often than not, Pin 1 can be found on the lower right corner of
the chip. Please refer to the diagram for the exact location.
3. Once you have figured out where the pin 1 locations are on both
chip and socket, align the module’s pins on an upright angle
against the socket. Using both thumbs, gently press the module
into the socket until all the pins are secured to their
designations.
Pin 1
Location
DiskOnChip
4. The installation is now complete and your module is now ready
for use.
NOTE: If you encounter difficulty installing your DiskOnChip

module,
please consult a qualified technician or engineer to perform the
installation.
3.7.2 Removing DiskOnChipModules
When removing a DiskOnChipmodule from its socket, please take
note of the following:
1. Loosen the contact of the module from its socket using a
screwdriver.
2. Insert the screwdriver’s flat head into a gap on either end of the
socket. Do not insert the screwdriver head on either side where
the pins are located. Doing so might damage the pins in the
process.
StockCheck.com

13
3. Slowly lift the screwdriver handle upwards. This will disengage
the module from its socket.
NOTE: If you encounter difficulty removing your DiskOnChip
 module,
please consult a qualified technician or engineer to remove it for
you.
3.8 VGA Controller
The onboard Intel 82845GV with 1MB or 8MB memory supporting CRT
display up to 1280 x 1024 x 32-bit. The HS-7001 provides one
connection method of a VGA device. VGA1 offers a single standard
CRT connector (DB15).
 VGA1: 15-pin CRT Connector (DB15)
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 N/C 10 GND
11 N/C 12 SDA
13 HSYNC 14 VSYNC
15 SCL
1
6
10
11
515
StockCheck.com

14
3.9 PCI E-IDE Drive Connector
IDE1 and IDE2 are standard 40-pin connector daisy-chain driver
connector serves the PCI E-IDE drive provisions onboard the HS-7001.
A maximum of four ATA/33/66/100 IDE drives can connect to the
HS-7001 via IDE1 and IDE2.
 IDE1: Primary IDE Connector
PIN Description PIN Description
1 RESET 2 GND
3 PDATA 7 4 PDATA 8
5 PDATA 6 6 PDATA 9
7 PDATA 5 8 PDATA 10
9 PDATA 4 10 PDATA 11
11 PDATA 3 12 PDATA 12
13 PDATA 2 14 PDATA 13
15 PDATA 1 16 PDATA 14
17 PDATA 0 18 PDATA 15
19 GND 20 N/C
21 PDREQ 22 GND
23 PIOW# 24 GND
25 PIOR# 26 GND
27 PIORDY 28 PR1PD1-
29 RPDACK- 30 GND
31 Interrupt 32 N/C
33 PDA1- 34 PATA66
35 PDA0- 36 PDA2-
37 PDCS1- 38 RPCS3-
39 HDD Active P 40 GND
1
240
39
3 5 7 9 17 19 21 23 25 27 29 31 33 11 13 15 35 37
46810 18 20 22 24 26 28 30 32 34
12 14 16 36 38
StockCheck.com