Boyo VTC461 R User manual

VISION
Wireless rear view camera systems
VTC461 R User's manual
Thank you for your choosing this product
GUser's manualX 1FScrewx2
~J5~
c ex~:~~~~~~~~~ 10 Filterx 1EPower detecting penX 1
BWireless transmission camera x1A 6' wireless receiving HT monitorX 1
Testing:
~
~
When the reverse gear is engaged, the system works automatically. Monitor
will be on at once. The wireless camera at the back of car will send signals
to the wireless monitor in front of car. Images at the back of car will be
shown clearly. When the car is running, the monitor could be at the video
input or turn off status automatically.
CD Turn the key to the on, the power of the car is on. ®Turn to the reverse gear, the rev~rse light is on
('C-- ---J
CD Take down the license plate. ®
Tow the camera power line(B) into the car though the interstices of
the car. ®
Install the camera onto the license plate. fix it with the spared screws(F).

@Find the power line from the reverse light with the
power detecting pen (El
I
Reverse I
Red cable hght
2P
F.B~"=';:k=,""'b;:le==~ J
Ground '=
'-'---~~--~~---'-"---'--~--'--------
®Find the power lines from the trunk at the back of car. ®Black clamp connects to any iron part of car. Use the red pen to test every power line from the reverse light
Cut off the power of car. until the LED light is on. Then you can ensure that this is the power line.
CD Connect the filter(O)(the"IN"side) to the reversing ®Connec.t the camera power lines to the filter(D)(the @Connect the pbwer lines as before.
light power line, anode to anode, cathode to cathode, "OUT"slde) ,anode to anode, cathode to cathode,
then fix the cables
with the rubberized fabric. then fix the cables with the rubberized fabric.
@Enlace and hind other lines properly.
Installation of power from the front reverse light
~
Redpowerlineconnectsloanode+12V
Power lines connection ~ Black wire connects to the ground wire.
1 ~BluepowerlineconnectsloreverSelight12V
.
'" DI0
0I
----===//===::::r
~ Video connects VCD/DVD signal input
1 ~ CD Find the pow" lines from the driving room.
LJ Cut off the pow" of 'ar.
Reverse
2Pl=R~e=d~,=ab=:te~=~ light
Black cable ..
Ground
®Black clamp connects to any iron part of car. Use the red pen to test every power line from the reverse light
until the LED tight is on. When you reverse the car, the LED light is on, when you don't reverse the car, the LED
tight isn't on. Then you can ensure that this is the reverse light power line.
®Connect the blue power line to reverse light12V
@Black clamp connects to any iron part of car. Use ®Connect the red power line to anode +12V power line. ®Connect the power lines as before.
the red pen to test any power
line from the car until
the LED light is on. Then you can ensure that this is
the anode +12V power line.
1 (
II
§J
(j) Enlace and hind other lines properly. ®Connect the
monitor power extending line (el to
the 6"
monitor according the arrow. ®
Tow the 6" monitor power line (Al to the original @Reviewing
rearview mirror,
clip it up.

BOYO·
Vision Tech America, Inc.
Name. _
Address _
Product Registration
Company._ ._. __ . _. .
City
__
Phone ~ ... . .. _ .. ._ ... ... .. __ .
State
Email.
ZI
p_____ .
Model No. Serial No.
Purchased Date Store Name
City/State of Store_. __ ~. .... ... ._ ..... _ ....... ........ __ ..... __

8OYO·
Vision Tech America, Inc.
625 Ellis St. Suite 102
Mountain View, CA 94043
Place
Postage
Stamp

Vision Tech America, Inc.
Limited One Year Warranty
This limited warranty is given to the end-user or the retail purchaser (referred to this warranty as
"Original Purchaser") that it will be free from defects in material and workmanship for aperiod of one
year from the date of the purchase of the new product (excluding accessory items such as power cords
and cables). Acopy
of the original proof of purchase and this warranty card with RMA number
given by Vision Tech America, Inc. is required to receive warranty service. In the unlikely event
that the new product should fail due to defect in material or workmanship, Vision Tech America, Inc. will
repair or replace the entire product, where each party will be responsible for one-way shipping.
This limited warranty does not cover any physical damage to this product, damage caused by im-
proper installation; improper use; misuse; neglect; repair of cracked, scratched, broken or modified
cosmetics; or parts that have been altered or removed; damages done by another device used with this
product resulting from use of non Boyo®- brand parts. This warranty is VOID if you purchased this prod-
uct as used, floor model sample, or refurbished; if the product has been altered or modified in any way
(including but not limited to attempted repair without authorization from Boyo®- Vision Tech America,
Inc. and/or alteration/removal of the serial number). This limited warranty does not cover the vehicle
of any damages or liabilities in which this product is installed or being installed. This product does not
guarantee avoidance of vehicle collision or accident, but it is used as an assistance to view the rear of
the car while in reverse mode.
If you think your product is eligible for warranty service, report to Vision Tech America, Inc. at 650-903-
9905 or email: info@boyovta .com to receive an RMA Number with further instructions.
Important: To send defective product for warranty service, you must receive RMA (Return Material Authorization) and include original proof
of purchase and this warranty card with the shipment.

Limited One Year Warranty
Headquarter
625 Ellis Street Suite 102
Mountain View, CA 94043
Tel: [phone]
Email: [email protected]
YlllON
Vision Tech America, Inc.