Boyo VTX3600 User manual

Version 1.0
Please read this user manual carefully before using this product.
Failure to understand operation procedures may result in injury.
EU Environmental Protection
Waste electrical products should
not be disposed of with household
waste. Please recycle where
facilities exist. Check with your
local authority or retailer for
recycling advice.
Model: VTX3600
Model: VTX3600
Digital Wireless Backup Camera
System with 3.6" TFT - LCD Monitor

Welcome
Thank you for choosing our backup camera system. Please
install and use the product in accordance with our operation
instructions. We will provide quality and reliable service for a variety
of vehicles including cars, trucks, and so on. W e implement rigid
quality control and testing to ensure the best performance of the
product as well as satisfactory service for you.
Packing List
Digital Wireless Monitor
Suction Cup
Transmitter Box
Video Out Cable
Power Supply Cable
10
Antenna for Monitor
Cigarette Lighter Adapter
10
Grommet
Camera Screws
In-line Wire Connectors

Digital Wireless
Power ON/OFF
Antenna
Pairing Button
Brightness
Revolving Button
Contrast
Power Indicator
Pairing Indicator
TFT-LCD
Power Supply
Socket
Video out
Structure
Rearview Camera
Installation
Installation of the wire camera.
(Only for reference) :
1. Drill three holes above the
license plate frame: one for
passing the cable through
the car body; two for installing
camera. Before drilling, check
whether there is any part
behind the hole-drilling position.
If there is, for example,
electronic part or fueling
system part, take all necessary
measures to avoid any possible
damage to these parts. If the
car has existing holes, please
skip this step;
2. After the hole is drilled, insert
the supplied washer, and then
pass the power cable through
the Grommet and into the car.
The Grommet shall be used to
prevent the metal side of the
hole from cutting the power
cable;
3. Adjust the camera to a suitable
angle for view;
4. Install Camera Screws we supplied
to the other holes with the
camera.
5. Connect the camera to the Transmitter Box,
Transmitter
box
Wire
Camera
Red
Black
+12VDC
REV LAMP
Reverse Lamp
Ground
Power
Connection
RCA
Connection
Power input Power output
Transmitter Box
Pairing Button
Power Supply Connection
Antenna
Wire Ca m e r a
Video output
Video input

Installation of the monitor:
1. Use the Suction Cup to install the monitor. The Suction Cup is stamped
on the front window glass.
2. Connect power of the monitor. There are two methods as
below:
A: According to the same steps, find power from the car power
circuit in front, and connect the cables correctly.
B: Use the Cigarette Lighter Adapter included in the package to
get the power form cigarette lighter socket
2
1
6. A detector to find the power:
how to find the power from the reverse light?
Instructions: black clamp connects to the ground wire. Use
the red pen to find the power from the reverse light until the
LED light is on. Then connect our red power line to the power
from the reverse light, and the black to the ground wire.
A detector
to find
the power
2P
Red wire
Black wire
Reverse
light
Ground
12
3
4
In-line Wire Connector Instructions
The camera can be wired directly to the reverse light circuit by
stripping the reverse light wires and then twisting the camera
wires to the exposed reverse light wires. Once they are connected,
wrap them with electrical tape. Do not attempt this if you are not
knowledgeable with electrical installation practices.
1.Insert the existing
wire to be tapped.
2.Insert the wire
to be attached.
3.Crimp tap and
then close lock
5.Find and connect the reversing light cable with proper
positive and negative electrodes.
6.Stand on the rear of the vehicle with a board(30X100cm)strait
stood on hand, reverses slowly to verify the function.
3. Connect the camera and wireless Transmitter Box.
4. Install the box on the side of the trunk.
Pairing the system
3 4
56

5, D efa ult S ett ing :
Pre ss the Br ig ht ne ss and Co nt rast bu tt on s at th e same
t i m e, and t h e re s e t is d o n e , bo t h c on t r as t , b r i g h t ne s s
an d ima ge or ien tat ion r etu r n to t h e de f au l t se t ti n g.
6, S ave t he se tti ngs :
Sy ste m wil l aut oma tic all y sav e all t h e us e r se t ti n gs .
Testing the System
* All the specifications are subject to minor change without prior notice.
Specifications
dBm
Operating Frequency
Bandwidth
2400－2483.5
4.4(20dB BW)
Transmitting Power +14dBm @ 16QAM EVM 5%,
+18dBm @ QPSK EVM 8%
Safety
Receiving Sensitivity
Unobstructed Effective Range
Antenna Gain
Items
Power Supply
Operation Temperature
TRANSMITTER SPECIFICATIONS
Specification
16QAM,QPSK,BPSK
Modulating/Demodulating Method
Unit
MHZ
MHZ
dBm
Proprietary Frequency Hopping
Signaling With Digital Modulation
-72dBm@QAM, -85dBm@QPSK
2(Omni-directional Dipole)
≥50
-10~+50°
DC 12V
dBi
m
15%~85%
-20~+60°
60±5g
66x35x12
Storage Temperature
Operation Humidity
Dimensions
Weight
VDC
℃
RH
mm
g
32 Bit ID
℃/°F
Max Consumption current mA DC 12V@250
The system is originally paired up from the factory setting, in any case
the system loosed pairing, please follow the below instructions to
pair up again.
1 Make sure camera and Transmitter Box are appropriate connected,
and both Transmitter Box and Monitor are powered up.
2 Press and hold the "Pair" button on the monitor for 3 second, the
orange light will start to flash and monitor shows a counting down
number from 30 to 0, you have 30 seconds to press and "Pair"
button on the Transmitter Box to pair up the system.
3 To use a pen or small tip to press and hold the "pair" button on the
Transmitter Box for 3 seconds when the Monitor is counting down.
The camera image should be showed up on the monitor, which means
the pairing succeed.
4 Video are able to be output from the monitor to bigger display device
such as TV or other screen with a RCA video input.
Normal Mirror Mirror Upside
Down
Normal Upside
Down
1，Im age O rie nta tio n:
T here ar e f o u r d i f f eren t wa y s t o v i e w t h e i m a ge f rom the
m o n i t o r, p r e s s t h e I m a g e O r i e n t a t i o n b u t t o n , y o u c a n
ch an ge the im ag e in f our dif fe ren t wa y, dep en ds on whe re
a n d h o w y ou ins t a l l th e c a me r a, ma ke s u r e yo u h av e th e
ri ght I mag e Ori ent ati on be f or e i t to b a ck u p yo u r ca r.
2, C ont ras t Adj ust men t:
Press the Contrast button to adjust the monitor contrast,
there are 7 levels set ti ng changes by eac h time press th e
Co ntr ast b utt on.
3, B rig htn ess A dju stm ent :
Press the Brightness button to adjust the monitor brightness,
the re are 7 levels se tt in g chang es by eac h time pr es s the
Br igh tne ss bu tto n.
4, O N/O FF:
T h e Mo n i t o r wi l l au to m at i ca l ly tu r n o n w h e n th e c a me r a
p ow e r ed u p , i f t h e M o n it or d oe s n o t t u r n o n , p r es s t h e
ON /OF F but ton o ne mo re ti me.

This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference,
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
FCC Information
Cautions
● The apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
● Tu r n of f th e Ca m era /Mo n it o r if the s ys t em i s no t in u se.
● The Camera/Monitor can only be completely disconnected
from the mains by unplugging the adapter.
● Do not cut the DC power cable of the apparatus to fit with
another power source.
● Attention should be drawn to the environment aspects of
battery disposal.
350
Items
LCD Screen Type
Lens Mount
DISPLAY
Specification
Unit
15%~85%
-20~+60°
Storage Temperature
Operation Humidity
℃/°
℃/°
RH
Effective Pixels
Brightness
320 X 240
3.6", TFT LCD
cd/m2200
Contrast
degree L:60/R:60/U:40/D:60
VIDEO
Frame Rate fps 30
Video Resulutions VGA
Video Compression MPEG-4
Video Signal Output CVBS，1Vp-p@75ohm
Video Output Format PAL/NTSC
RF
Operating Frequency MHz 2400－2483.5
Bandwidth 4.4 20dB BW( )MHz
Modulating/Demodulating Method 16QAM,QPSK,BPSK
Transmitting Power dBm +14dBm @ 16QAM EVM 5%,
+18dBm @ QPSK EVM 8%
Receiving Sensitivity dBm -72dBm@QAM, -85dBm@QPSK
Safety
Proprietary Frequency Hopping
Signaling With Digital Modulation
32Bit ID
Antenna Gain dBi 2(Omni-directional Dipole)
Unobstructed Effective Range m≥50
GENERAL
Power Supply DC +12/24V
Consumption Current mA 250(max)
Weight g128±20
Dimensions mm 108x75x38
Operation Temperature -10～+50
Specifications
* All the specifications are subject to minor change without prior notice.
BOYO SENSORS BACK UP SENSOR SYSTEMS