Bradley Equa-Flo EFT1 User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
215-1736 Rev. B EN 12-03-009
© 2012 Bradley
Page 1 of 4 8/7/2012
S59-1000T1
Bradley Equa-Flo™EFT1
Pressure-Balancing Shower Valve
Table of Contents
LCD Display Information...................................................2
Rough-in/Dimensional Information ...................................2
Installation Instructions .....................................................2
Connecting Valve and Adjusting Temperature..................3
Attach Escutcheon and Handle ........................................4
IMPORTANT!
Read this entire installation manual to ensure proper installation. When finished
with the installation, file this manual with the owner or maintenance department.
Compliance and conformity to local codes and ordinances is the responsibility of
the installer.
Hot limit screw is set in the maximum temperature position. Failure to adjust
properly may result in serious scalding. This valve may not protect from scalding
if there is a failure of other temperature-controlling devices elsewhere in the
plumbing system. Excessive heat may cause damage to internal parts.
Separate parts from packaging and make sure all parts are accounted for before
discarding packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Make sure that all water supply lines have been flushed and then completely
turned off before beginning installation. Debris in supply lines can cause valves
to malfunction.
Product warranties may be found under “Products” on our web site at
www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List

Supplies Required
Teflon Tape
Allen Key Wrenches
Screwdriver
1/2" NPT Brass Pipe Plug
Adjustable Wrench
ASSE 1016 & UPC Certified
For use with shower heads rated
at 5.7 L/min (1.5 gpm) or higher.

S59-1000T1 Installation
28/7/2012 Bradley
•฀215-1736฀Rev.฀B;฀EN฀฀12-03-009Shower Only Installation
5"
(127)
6-1/2" (165)
w/ Stops
2-1/2" (64)
w/o Stops
Hot Cold
Front View
(mm)
Dimensional Information
LCD Display Information
The Bradley Equa-Flo™EFT1 S59-1000T1 LCD Shower Valve is designed to operate for up to 2 years on a set of high-quality
alkaline batteries*. Bradley strongly recommends using only high-quality, name-brand alkaline batteries for maximum performance.
When operating at normal room temperatures, the LCD display will convey accurate water temperatures between 40°F –120°F
(4°C–49°C). For safety and comfort, a number of special features are built into the display:
1. Display will flash "HHH" when water temperature exceeds maximum operating limit of 120°F (49°C). It will display "LLL"
when water temperature falls below minimum operating limit of 40°F (4°C).
2. Display will refresh every 2 seconds when the water temperature reaches 70°F (21°C). If the water temperature is below
70°F (21°C), the display will refresh every 10 seconds.
3. The unit can be configured to display °F or °C by a slide switch inside the display's battery compartment (see Step 2).
4. A"Low Battery" indicator will turn on when batteries have approximately one month of power remaining.
* AAA alkaline batteries, supplied.
8"
(203)
72"
(1829)
40"
(1016)
Temperature
Probe Tee on
Bottom of Valve
1/2"
NPT
1/2"
NPT
1/2" NPT Plug
(not supplied)
3-1/2" (89) Max.
3-1/4" (83) Min.
3-7/8" (98) Max. Depth
3-5/8" (92) Min. Depth
Tub/Shower Installation
12"
(305)
Use rough-in
hole template
(215-1735) for
finished wall
(provided).
3-5/8"
(92)
3-1/4"
(83)
3/4"
(19)
2-3/4"
(70)
6-3/4"
(175)
R: 2-3/4"
(70)
Valve
Center
1-7/8"
(48)
4-1/2"
(114)
1-1/4"
(32)
Floor
8"
(203)
24"
(610)
72"
(1829)
48"
(1219)
Temperature
Probe Tee on
Top of Valve
1/2"
NPT
1-1/2"
(38)
3-1/4" (83) Max.
2-1/2" (64) Min.
3-7/8" (98)
Max. Depth
3-1/8" (79)
Min. Depth
1/2" NPT Plug
(not supplied)
Floor
Rough-in 1/2" NPT hot and cold water
supply (supplied by installer).
For finished wall, rough-in hole using
template (215-1735) provided.
"Back-to-Back" Installation
Hot
Cold
Standard
Install
Supplies
Reversed
Installation Instructions
Rough-in
1

Installation S59-1000T1
Bradley Corporation฀•฀215-1736฀Rev.฀B;฀EN฀฀12-03-009฀8/7/2012฀3WARNING! The temperature limit stop has been factory
preset for maximum temperature operation.
Failure to adjust the limit stop to a safe shower
temperature could result in the user being
scalded.
APosition valve with port labeled “UP” towards showerhead.
Connect valve to hot and cold supplies and showerhead
or tub spout supplies (see rough-in diagram.)
D
Turn on hot and cold supplies to pressurize valve and check for
leaks. (Valve will not operate unless both hot and cold supplies
are turned on.) Set limit stop by loosening set screw on limit
stop and repositioning to the desired temperature (do not
remove the inner off-stop!)
C
H
To Showerhead
Up
Alignment
Mark on
Cap
Arrow
on Cap
Hot Limit
Stop
Off
Stop
Set Screw
You can fine-tune the hot limit
stop position 1/2 spline by
flipping it over.
Limit Stop
Normal
Limit Stop
Flipped
FOR "BACK-TO-BACK"
INSTALLATIONS
ATurn off water supplies and remove (2)
hold-down screws from the "reversed"
valve. Rotate cap and cartridge
assembly 180° and re-install screws. B
Remove both limit stops and rotate
180°. Align with alignment mark
as shown. Adjust hot limit stop the
same as for standard installation.
C
H
To Showerhead
Up
Arrow
on Cap
The included foam rim seal
may be applied to the back
of the escutcheon inside the
outer edge, with the seam at
the bottom. 1/4"
(6mm)
BSet °F/°C selection as desired. Insert (2) AAA
batteries (supplied) and attach back housing.
(2) AAA
Alkaline
Batteries
°F/°C Slide
Switch
Silicone
Gasket Back
Housing
Probe
CInsert probe to depth shown
and tighten nut securely.
Probe/Tee
Orientation
(Top View)
45°
Connect Valve and Adjust Valve Temperature
2

S59-1000T1 Installation
48/7/2012 Bradley
•฀215-1736฀Rev.฀B;฀EN฀฀12-03-009APlace the escutcheon on the wall over the
valve and secure with the screws provided.
BPlace handle on stem as shown, and tighten screw.
Attach Escutcheon and Handle
3