BrandMotion F Series User manual

! INSTALLATION!INSTRUCTIONS!
3600 Instructions 9-1-15 Page 1 of 19
F-Series 360º Vision System for Aftermarket Radio/Display
(Kit # AVMS-3600)
DUE TO THE COMPLEXITY OF THIS KIT
PROFESSIONAL INSTALLATION IS REQUIRED
CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit: Tools
& Supplies Needed
:
2004-2014 Tailgate handle w/camera
360º camera module
Key box power/image buttons
Front camera w/grill mount and harness
2 side mount cameras w/pods and harnesses
2 video output RCA cables
Power/camera input harness
2 side camera templates
Mounting screws and gaskets
These instructions
Wire strippers
Wire cutters
Electrical tape
Zip ties
Plastic panel removal tools
Screwdriver
7 mm socket
Drill
Large Uni-bit/drill bits
Hole saws
T-15 Torx
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.
Section 1:
Front camera installation
1. Front camera is mounted in the grill below
the Ford emblem.
2. Mount camera in housing using the bracket
and screws provided.
3. Mount the housing using the provided
screws to the grill and putting the caps in
the holes to close them.

! INSTALLATION!INSTRUCTIONS!
3600 Instructions 9-1-15 Page 2 of 19
4. Run the camera harness along the under
hood covering, down the drive side hinge.
Zip tie the harness to the hinge so the
harness will not kink or cut.
5. Run harness into the vehicle though the
factory grommet in the drivers side firewall.
6. Route the camera harness to the location of
the 360º module.
Section 2:
Side Mirror Camera installation
1. The inter door panel will have to be
removed for installation of the side
cameras.
2. Working on the driver side door. With the
door closed, place the template sticker
(
marked LHD ) on the bottom side of the
mirror with arrow aiming away from the
vehicle. Perpendicular to the side of the
body. (
Do not go by mirror lines or angles .)
3. Make sure the template is to at least the
middle to outer edge of the mirror. (
The
camera needs to see only a little of the side
of the vehicle and mainly the ground and
objects next to the vehicle
.)
4. Remove the door panel and the 3 nuts that
are holding the mirror to the vehicle.
5. Place the mirror on a soft or padded surface
and remove the glass from the mirror.
(
Each vehicle is different, but most are
mounted by a center circle and will unclip
from it
.)
6. After the glass is removed, check to see if
where the templates are placed there is
clearance for the camera and will not cut
into anything in the mirror housing. (
If the
template has to be moved make sure to
keep the arrow aiming the same way
.)
7. Drill a hole in the bottom of the mirror using
a hole saw or Uni-bit to the size on the
template. Which is 1 1/8”

! INSTALLATION!INSTRUCTIONS!
3600 Instructions 9-1-15 Page 3 of 19
8. With the sticker still in place, drill the (2)
mounting screw holes with a 1/16 drill bit.
(
Do not go all the way though .)
9. The side cameras, brackets and pods are
labeled for right-RH and left-LH. Make sure
to assemble them correctly. Use caution not
to loss the tiny screws to mount the
cameras to the brackets and the brackets to
the pods.
10. Using the LH camera assembly, attach the
foam gasket to the bottom side of the pod,
lining up the notch in the foam with the
bump on the pod.
11. Remove the tape from the foam gasket and
mount the camera pod to the mirror. Use
the self-tapping screws provided to mount
the pods to the underside of the mirror. (
Do
not over tighten the screws; it may strip out
the plastic.)
12. Route the camera cable though the mirror
and out of the mounting side of the mirror.
Make sure not to block any movement of
the mirror glass or folding.
13. Route the cable in the door and remount
the mirror to the vehicle.

! INSTALLATION!INSTRUCTIONS!
3600 Instructions 9-1-15 Page 4 of 19
14. You will next pin the camera cable wires
into the provided connecter. Inset the pins
into the connecter until they make a “snap”
sound. Use the left side camera harness to
match up where the pin locations are.
(See
Diagram chart 1a. at end of instructions for
all camera pin connections.)
15.
Attach the camera cable to the harness and
route though the door to the rubber boot.
Secure the harness to the factory wire
harness with zip ties.
16. Route the harness out though the rubber
boot into the vehicle. (
The vehicle might
have a Molex or plastic plug in the door of
body, if so drill a hole in the plug if there is
any room to, if not drill a hole lower in the
door jus under the rubber boot and the
same if the plug is in the body. Grommet
and seal any holes that might be drilled.)
17.
Route the harness to the 360º module.
18.
Reinstall the mirror glass into the mirror and
reinstall the door panel.
19.
Repeat the process on the passenger side
door and then continue to the next section.
Section 3:
Rear camera installation
1. The rear camera on this vehicle will be in
the tailgate handle. The camera is already
mounted to the handle.
2. Remove the trim panel on the backside of
the tailgate, by removing the Torx screws
holding it in place.
3. Unclip the latch rods the go to the handle.
( If equipped with a rear camera, unplug it
from the harness.)
4. Loosen the (2) 10 mm nuts holding the
handle in place.
5. Remove the handle and install the new
handle with the 360º camera installed.
6. Connect the camera cable to the rear
camera harness and heat shrink or tape the
connection.
7. Route the harness through the tailgate and
into the lower bed frame. (
If holes do not
exist in the tailgate or bed frame you must
drill new holes in to each to run harness.
Make sure to use grommets and seal up
holes to prevent rust or cutting of harness.)
8. Route the harness on the underside of the
vehicle. Use zip ties to hold harness in place
and be careful to avoid any moving parts or
exhaust.

! INSTALLATION!INSTRUCTIONS!
3600 Instructions 9-1-15 Page 5 of 19
9. Route the harness in to the vehicle by
coming up though a grommet in the floor or
the grommet under the hood in the firewall.
10. Route the rear camera harness to the 360º
module.
Section 4:
360º module installation
1. Connect the correct camera plugs to the
360º module. Front, rear, left side, right
side, CVBS and CVBS RV.
2. The CVRS output, is video output controlled
by the power on/off button to the system. It
is connected to the AUX video input on the
aftermarket radio/display.
3. The CVRS RV output, is video output when
the accessory is powered on. It is
connected to the back-up camera input on
the aftermarket radio/display.
4. If not done so yet connect the power
harness to the 360º module. Wire up the
power connections, yellow is constant, red
is accessory, black is ground, blue is
reverse.
5. Do not mount the 360º module; you will
need to get to it for calibration of the
cameras.
6. Plug in the Key Box and mount to the right
side of the steering column on the das trim
with the tape provided.
7. To turn on the system press the power
button on the Key Box. To change camera
views press the car image button. A long
press will show a full front view another
long press will show a full rear view.
8. Place the vehicle into reverse to see the
rear camera image on the screen.