BrandMotion 9002-8838 User manual

INSTALLATION(INSTRUCTIONS(
9002-8838 Instructions 9-23-16.docx Page 1 of 6 GS
Jeep Wrangler Rear Vision Camera,
2007 – Current (Kit # 9002-8838)
Items Included in the Kit
Camera
Chassis Harness
Zip lock bag with 15 Wire Ties & 3 Push Nuts
These Instructions
22--pin white connector w/ video RCA (for factory
display radio)
Required Tools & Supplies
T15 & T20 Torx Bits
7mm & 10mm Sockets
Phillips Screwdriver
Plastic Trim Removal Tool
Soldering Iron, Solder, & Heat Shrink Tubing
(RECOMMENDED) or T-taps as an alternate
splicing method
Electrical Tape
Please read so you do not VOID the
warranty:
If the camera harness is run through the center on the
camera bracket, it will cut the camera harness. This will
void the warranty on the camera.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com

INSTALLATION(INSTRUCTIONS(
9002-8838 Instructions 9-23-16.docx Page 2 of 6 GS
Install Camera
Step 1: Loosen lug nuts to remove spare tire.
Step 2: Slide Camera on studs placing harness end on
top of tire carrier. Do not run harness through the
camera bracket opening .
Step 3: Temporarily replace spare tire to check wheel
clearance to Camera.
Wheel Alignment for Camera Clearance
Step 4: Remove spare tire and slide (3) supplied Push
Nuts on the studs.

INSTALLATION(INSTRUCTIONS(
9002-8838 Instructions 9-23-16.docx Page 3 of 6 GS
Install Chassis Harness
Step 5: Plug the Camera connector into the gray
Chassis Harness connector, and insert RCA connector
end of supplied Chassis Harness through the rear gate
vent behind tire carrier.
Step 6: Using a plastic trim removal tool, remove
interior panels on inside of rear gate.
Step 7: Pull harness through the rear gate openings.
Step 8: Use supplied Wire Ties to secure Chassis
Harness to existing harness.
Step 9: Use supplied Wire Ties to secure Chassis
Harness to fabric factory wire cover. CAUTION: Leave
enough slack to allow gate to open fully.
Step 10: Use a T20 Torx bit to remove subwoofer box.
Step 11: Using a plastic trim removal tool, pry off rear
seat belt closeout.

INSTALLATION(INSTRUCTIONS(
9002-8838 Instructions 9-23-16.docx Page 4 of 6 GS
Step 12: Using a plastic trim removal tool, remove rear
access panel to expose 10mm bolt, and remove bolt.
Step 13: Pull out subwoofer box slightly to gain access
to run Chassis Harness along existing harness
Step 14: Pull back carpet and continue running Chassis
Harness forward.
Step 15: Run Chassis Harness under B-pillar cover to
passenger door sill. Use a plastic trim removal tool to
remove the (2) plastic push pins and remove passenger
sill plate/kick panel.
Step 16: Use a 10mm socket to remove the existing nut
located behind the passenger kick panel and attach
ground eyelet of Chassis Harness to chassis ground.
NOTE: Step 17 is for aftermarket radios/displays
ONLY. For factory display radios, skip step 17.
Step 17:In the factory wire harness located in the
passenger foot well, locate the White/Gray Reverse
signal wire and splice Green Reverse wire from supplied
Chassis Harness. RECOMMENDED: Solder and cover with
heat shrink tubing or use T-tabs as an alternate
connection method.
Step 18: Remove rubber bin insert from top of dash.
Step 19: Remove 7mm bolt .

INSTALLATION(INSTRUCTIONS(
9002-8838 Instructions 9-23-16.docx Page 5 of 6 GS
Step 20:Using a plastic trim removal tool, remove
window switch panel.
Step 21: Disconnect harness from window switches.
Step 22:Remove 7mm bolt.
Step 23:Remove driver knee bolster cover.
Step 24:Remove (2) 7mm bolts on both sides of the
steering column.
Step 25: Remove center stack/cluster surround.
Step 26: Remove glove box for access and run Chassis
Harness toward center of dash.
Step 27: Using a plastic trim removal tool, remove
HVAC panel.

INSTALLATION(INSTRUCTIONS(
9002-8838 Instructions 9-23-16.docx Page 6 of 6 GS
Step 28: Run Red 12v+ ignition wire of supplied
Chassis Harness to ignition controlled power point on
HVAC panel power point.
NOTE: Step 29 is for factory display radios only. If
using an aftermarket radio/display refer to step
17.
Step 29:Splice Red power wire and the green trigger
wire from the chassis harness to Blue/Red wire on back
of power point. RECOMMENDED: Solder and cover with
heat shrink tubing or use T-taps as an alternate
connection method.
Step 30: Plug the Chassis Harness RCA connector into
your aftermarket display.
Step 31: If you are using a factory display radio, You
will need to have the radio programmed at the
dealership for the back-up camera to display.
Step32: Plug in the 22—pin white connector to the
open connector on the back of the radio.
Figure 1
Step 33:Connect White 22-pin Connector to radio
along with all remaining radio connectors before
reinstalling radio head unit and all trim removed.
Step 34:Connect male RCA of camera into female
RCA of jumper harness and proceed to the Dealer
Programming Instructions (Included).
Dealer Programming Instructions
PARK VIEW REAR BACK-UP CAMERA
VEHICLE CONFIGURATION
Vehicle VIN must be updated with the sales code of the
added accessory in order to enable system functionality.
Using the DealerCONNECT website and the scan tool,
complete the procedure below:
A. Log on to https://dealerconnect.chrysler.com
B. In the “Vehicle Option” screen under “Global Claims
System” category in the “Service” tab, enter the
VIN and add the following sales code: XAC (PARK
VIEW REAR BACK-UP CAMERA) as a “Dealer
Installed Option.”
C. Confirm that the new sales code has been
successfully added to the VIN. With the scan tool
connected to both the internet (via Ethernet port or
wireless connection) and the vehicle, perform the
following steps:
D. Using the scan tool, select VEHICLE PREPARATION
and then select RESTORE VEHICLE
CONFIGURATION.
E. Follow the step-by-step instructions on the scan
tool to complete the Park View Rear Back-Up
Camera vehicle configuration.
Step 35: Test the system. Start vehicle and shift into
Reverse in order to check that all connections were
made properly. If all of the connections are correct you
will see the camera image displayed on your aftermarket
display.
Step 36: Reassemble vehicle. Follow your disassembly
steps in reverse order, taking care not to bind the
harness wiring when reinstalling trim.