BrandMotion AVMS-3701v3 User manual

! INSTALLATION!INSTRUCTIONS!
AVMS-3701v3 Instructions 11-27-17.doc Page 1 of 9
2007-2018 (JK) Jeep Wrangler 360º System for
Factory MyGig Display
(Kit # AVMS-3701v3)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Tools & Supplies Needed:
MyGig 6.1” factory display interface
Interface Video/Power harness
360º camera module
IR and remote control (not required)
Key box power/image buttons
Rear camera and Front camera
Front lower bumper mount and harness
Rear spare tire adjustable camera mount
2 side mount cameras w/pods and harnesses
Video output RCA cable
Power input harness
2 side camera templates
Mounting screws and gaskets
These instructions
Wire strippers
Wire cutters
Electrical tape
Zip ties
Plastic panel removal tools
Digital Volt Meter / BCM safe test light
Screwdriver
Socket set
Wrench
Uni Bit
Drill
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.

! INSTALLATION!INSTRUCTIONS!
AVMS-3701v3 Instructions 11-27-17.doc Page 2 of 9
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
REAR CAMERA INSTALL
1. Remove the spare tire off of the carrier.
(Use caution when removing tire.)
2. Open rear gate and remove trim from inside
of gate by using plastic panel removal tool.
3. Mount the bracket on the rear tire mount, after
bracket is on, slide on the 3 push nuts over the
studs.
4. Run the harness into the rear gate through the
factory gromet.
5. Run rear camera harness through top hole of
tire carrier.

! INSTALLATION!INSTRUCTIONS!
AVMS-3701v3 Instructions 11-27-17.doc Page 3 of 9
Adjustment Bracket for Camera Clearance using
Phillips Screwdriver and 3/8” Wrench or Socket Drive
Note: Short Bracket has been designed for Factory
offset wheels. Use the Long Bracket for wheels with
larger offsets.
6. Remount spare tire on carrier. (MAKE SURE NOT
TO PINTCH THE CAMERA HARNESS.)
7. Use a T20 Torx bit to remove subwoofer box.
8. Using a plastic trim removal tool, pry off rear
seat belt closeout.
9. Using a plastic trim removal tool, remove rear
access panel to expose 10mm bolt, and remove
bolt.

! INSTALLATION!INSTRUCTIONS!
AVMS-3701v3 Instructions 11-27-17.doc Page 4 of 9
10. Run the rear camera harness alone the
factory harness. Use zip ties to secure to
the factory harness.
11. Run the camera harness through the factory
cloth door boot, use a long zip tie or a fish
tape.
12. Finish running the harness to the front
glove box area on the passenger side of the
vehicle.
13. Remove the glove box to gain access to the
back side.
SIDE CAMERA INSTALL
1. Place template stickes under the side mirrors.
The arrow should be perpenduiculr to the
vehicle body, pointing away for the vehicle.

! INSTALLATION!INSTRUCTIONS!
AVMS-3701v3 Instructions 11-27-17.doc Page 5 of 9
2. Repeat for other side mirror as well.
3. Remove the door panel from the vehicle,
remove trim behind door handle and remove the
trox screw.
4. Remove the inter trim on the pull handle to gain
access to the two screws.
5. Remove the (2) Torx in the lower front of the
door.
6. With the door panel remover, unplug the mirror
harness and connect a pull wire to be able to
pull the harness back through the door.
7. Remove (2) Torx bolts on the inter door frame
to remove mirror. (when bolts are taken out the
mirror might fall, hold on to the mirror while
doing this.
8. Remove the mirror and pull harness through the
door.