BriskHeat TOTE series User manual

Wrap-Around Tote
Tank / IBC Heaters
(TOTE and TOT Series)
Instruction Manual
Read and understand this material before operating or
servicing this heater. Failure to understand how to safely
operate this heater could result in an accident causing serious
injury or death. This heater should only be operated by
quali ed personnel.
TOTE Series
TOT Series

TABLE OF CONTENTS
INTRODUCTION
The symbol above is used to call your attention
to instructions concerning your personal safety. It
points out important safety precautions. It means
“ATTENTION! Become Alert! Your Personal
Safety is involved!” Read the message that
follows and be alert to the possibility of personal
injury or death.
SAFETY ALERT SYMBOL
Immediate hazards which WILL result in severe
personal injury or death
Hazards or unsafe practices which COULD result in
severe personal injury or death
Hazards or unsafe practices which COULD result in
minor personal injury or property damage.
SAVE THESE INSTRUCTIONS!
Additional copies of this manual are available upon request.
2BH Thermal® Corporation. Home of BriskHeat® Products. All rights reserved.
Wrap-Around Tote Tank /IBC Heater (TOTE & TOT Series)
BriskHeat® Wrap-Around Tote Tank
/ IBC Heaters are designed for
maintenance heating of caged,
plastic, or metal tote tanks / IBCs.
For successful operation of these
heaters, read and understand these
instructions prior to use.
Introduction...................................................................
Safety Alert Symbol.......................................................
Important Safety Instructions……………......................
Speci cations................................................................
Installation / Operation Instructions.……......................
Troubleshooting Guide……………………………..........
Warranty........................................................................
2
2
3
4
5
7
7

IMPORTANT SAFETY INSTRUCTIONS
A person who
has not read and
understood all
operating instructions
is not quali ed to
operate this product.
3
End User Must Comply to the Following:
BH Thermal® Corporation. Home of BriskHeat® Products. All rights reserved.
• Do not immerse heater in
liquid.
• Keep sharp metal objects
away from heater.
• Keep volatile or combustible
material away from heater
when in use.
• Keep enclosure cover tight
while circuits are alive.
Failure to observe these
warnings may result in electric
shock, risk of  re, and personal
injury.
• Inspect heater before use. Do
not use heater with torn or worn
surfaces.
• Do not repair damaged or faulty
heater.
• Do not crush or apply severe
physical stress on heater or cord
assembly.
• Unplug heater when not in use.
• Use heater for heating tote tanks /
IBCs only. Use speci c sized heater
with same sized tote tank / IBC. Do
not use for other applications.
Failure to observe these warnings may
result in personal injury or damage to the
heater.
• Only quali ed personnel
are allowed to connect the
electrical wiring.
• All electrical wiring must
follow local electrical codes.
• Final installation/wiring
is to be inspected by
the authority who has
jurisdiction in the area that
the heater is installed.
• The end-user is responsible for
providing a suitable disconnecting
device.
• The end-user is responsible for
providing suitable over-protection
device. It is highly recommended that
a ground fault circuit breaker be used.
Wrap-Around Tote Tank /IBC Heater (TOTE & TOT Series)

GENERAL SPECIFICATIONS
4BH Thermal® Corporation. Home of BriskHeat® Products. All rights reserved.
Wrap-Around Tote Tank /IBC Heater (TOTE & TOT Series)
• Full coverage plug and play system
• Two separate heat zones
• Silicone impregnated cloth facing and liner
• 1/4” (6mm)  berglass insulation
• Patented ground for your safety
• Voltage: See identi cation label
• Total wattage: See identi cation label
• Adjustable thermostat: 50-160°F (10-71°C) or thermostat control at speci c
temperature. See identication label.
• Built-in manual reset high-limit safety thermostat set at 195°F (91°C) for each
heat zone
• Power cord 6 feet (1.8M) long with standard power plug:
120VAC = NEMA 5-15
240VAC = NEMA 6-15
Other voltages = bare wire
• Optional insulated top cover [reduces heat loss]
• Fits any tote tank width from 40” x 40” (1016mm x 1016mm) to 48” x 48”
(1219mm x 1219mm)
TOTE Series: Units with Adjustable Straps and Buckles

INSTALLATION / OPERATION INSTRUCTIONS
Read and understand this entire
manual before operating this heater
5
BH Thermal® Corporation. Home of BriskHeat® Products. All rights reserved.
STEP 1
Remove heater from box. Make visual inspection of heater. Do not use if torn or
damaged.
Wrap-Around Tote Tank /IBC Heater (TOTE & TOT Series)
The use of two
individuals is highly
recommended for this
installation
TOT Series: Units with Velcro Closures
• Designed for speci c size. See identi cation label.
STEP 2
For units with adjustable nylon straps and buckles:
Heater should be placed on a clean, dry surface. Locate “mouse-hole” on heater.
Loosely wrap heater around IBC / tote tank with the mouse-hole positioned to
accommodate the exit spigot. The adjustable thermostat control knobs must be
facing outside (if applicable) and power cord exiting at the bottom of the heater.
Secure the two top straps by fastening the quick-release plastic buckle. Overlap
the side of the heater with the nylon straps secured closest to the edge on the
outside, over any additional amount of the  ap underneath. Use the provided
handle at the bottom of the heater to assist in securing the bottom side strap
and tighten. Secure and tighten the middle and top straps. All  ve straps should
now be  rmly tightened so the heater is tight against the tote tank / IBC with no
sagging or bundling. Cover the top of the tote tank / IBC with optional insulation
cover.

6BH Thermal® Corporation. Home of BriskHeat® Products. All rights reserved.
Wrap-Around Tote Tank /IBC Heater (TOTE & TOT Series)
STEP 3
Plug standard 3-prong plug (if applicable) to appropriate electrical power
supply. The power connection must be adequately rated to electrically support
the voltage and amperage of the heater. The identi cation label located on the
power cord displays voltage and amperage requirements. Follow all local
electrical codes for proper electrical connections.
STEP 4 (For units with adjustable thermostats)
Adjust temperature control knobs to desired settings on both top and bottom
zones. Heater can be adjusted 50-160°F (10-71°C).
For units with velcro closure:
Heater should be placed on a clean, dry surface. Loosely wrap heater around
IBC / tote tank with the velcro openings positioned to accommodate the exit
spigot. The adjustable thermostat control knobs must be facing outside (if ap-
plicable) and power cord exiting at the bottom of the heater. Secure the two top
straps by attaching the velcro. Attach velcro closure on the side so heater is tight
against the tote tank / IBC with no overlapping, sagging or bundling. Cover the
top of the tote tank / IBC with optional insulation cover.
Note: Units with velcro are designed for an exact size. DO NOT overlap heater.
STEP 2 continued

TROUBLESHOOTING GUIDE
Please read this guide prior to contacting BriskHeat®. This guide is designed to
answer the most commonly asked questions. If you are unable to identify the
problem or need additional assistance, please contact your
local distributor/ representative or us at 1-800-848-7673, 614-294-3376, or
[email protected].
7
BH Thermal® Corporation. Home of BriskHeat® Products. All rights reserved.
PROBLEM SOLUTION(S)
Does not heat Verify heater is connected to proper voltage. The
identi cation label located on the power cord displays
the heater’s voltage requirement.
Unplug the heater, press both manual reset buttons and
plug back in.
Check to see if there is a resistance reading (not an
open circuit) in heater using an ohm meter.
Circuit breaker is tripping Validate that the circuit breaker is capable of handling
the amp requirement of heater. The identi cation
label located on the power cord displays the heater’s
amperage requirement.
Examine heater and cord for any damage.
Does not  t Con rm that the heater provided was designed to  t
around your speci ed tote tank / IBC.
If the heater was designed for the speci ed tote tank /
IBC, please call 1-800-848-7673 or 614-294-3376 for
further assistance.
Something has lightly spilled on exterior
or interior
Apply any general household cleaner, that does not
contain any silicone rubber dissolving type
ingredients, with a clean cloth fabric.
Wrap-Around Tote Tank /IBC Heater (TOTE & TOT Series)
WARRANTY INFORMATION
BriskHeat® warrants to the original purchaser for the period of eighteen (18)
months from date of shipment or twelve (12) months from date of installation,
whichever comes  rst. Contact factory at 1-800-848-7673 (toll free, U.S. /
Canada) or 614-294-3376 for complete details.