Bristan QD SHXSMFF C D3 Wiring diagram

Secure the shower to
the wall mount, ensuring
filters are in place.
2
5
Identify the
required position of
the valve and prepare
the water supply pipes.
Supply pipes should
be 150mm apart.
Using the backplate
supplied with the
wall mount, mark
and drill holes.
Secure the isolators
onto the backplates;
ensuring the olives
are positioned
over the pipework
correctly.
Secure the shrouds against
the rubber fixing plates.
4
3
1
Installation
Rotate the shroud until
the opening aligns with
the isolation screw.
Turn the screw to isolate
the water. Reverse the
process when turning
the water back on.
1
Isolation 2
Remove the concealing
cap from the shroud.
Secure the rubber and metal
backplates into place.
21mm21mm
REMEMBER
To service
your
product!
Operation
REMEMBER
hot on the left,
cold on the
right
IMPORTANT
Pack Contents
150mm
Centres
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0 60°C
65°C
Specifications
Maximum Static Pressure: 10.0 bar
Inlet Water Temperature
15mm
Compression
Inlet Connections
Min: 0.2 bar Max: 5.0 bar
Working Pressures
The inlet hot water must
be at least 10°C above the
required blend temperature.
Factory pre-set
42°C
Inlet Dimensions
5°C
25°C
Cold Water Supply
Min: 5°C Max: 25°C
Hot Water Supply
Tools You’ll Need
Flat head
Screwdriver
Cross head
Screwdriver
Hexagonal Keys Socket SpannerPipe CutterPencil Drill Adjustable
Spanner
Installation Instructions
& User Guide
Please leave these instructions
with the end user
Product Code: QD SHXSMFF C (D3)
All products manufactured and supplied by Bristan are safe to use provided that
they are installed, operated and receive regular maintenance in
accordance with these instructions.
This product needs to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999 and
current by-laws. For full Installation Requirements & Notes (IRN) please
visit wras.co.uk/directory.
Isolation valves must be fitted to the inlet water supplies to ensure ease of future
maintenance.
Before installing this product the water supply must be thoroughly flushed in
order to remove any swarf, solder etc.
This product must not be modified in any way as this will invalidate the
guarantee.
Full access must be made available for future maintenance/servicing purposes.
Before drilling into walls, check that there are no hidden electrical wires,
cables or water supply pipes. This can be checked with the aid of an
electronic detector.
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
If in doubt, contact a registered plumber or your Local Water Authority or
the Secretary of the Institute of Plumbing, address as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: [phone]
Prior to Installation
60-65°C Recommended
HotHot
ColdCold
OnOn
OO
x2
x2
x1
x1
x1
x1 x1
x1
x1
x1
150mm Centres

Remove the
temperature and
flow handles.
4
7
3
2
5Troubleshooting
To reduce the build up of
limescale and to ensure this
shower works to its maximum
performance we recommend
this shower is serviced every
6-12 months depending on the
hardness of your water.
To replace any spare parts for
your shower why not scan the
below QR Code and search
for your product.
Spare Parts
Servicing Intervals
Maintenance - Cartridge Cleaning
1
6
Symptom Cause Remedy
No flow or
low flow rate
partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on and o
as flow rate or pressure is too low.
Increase water flow rate or
pressure through system.
Head of water is below the
minimum distance required.
2 meters minimum required.
Hot or cold water being drawn o elsewhere
causing pressure changes or instantaneous
boiler temperature changes.
Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of debris and
any airlocks.
Water
dripping
from shower
This is normal for a short time after using the
shower.
This is caused by residual water tension, the build up of
water in the shower.
If water continues to drip,
possibly due to the cartridge
Remove cartridge and clean, refer to 'Maintenance' section
before starting any maintenance.
Shower does
not turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer solid guarantees
on all our products, eective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register.
For any other queries, please call our Customer Service on 0330 026 6273 where our expert team
of advisors will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
Using the wall
mount, isolate
both shower
inlets before
carrying out any
maintenance.
4
2
1
Remove the
temperature
handle and
temperature stop.
Reverse the steps to
replace the temperature
stop and handle.
Turn the shower on and set
the temperature to the
maximum setting. Wait for
the temperature to stabilise.
Turn cartridge spindle clockwise
to decrease the temperature.
Turn cartridge spindle
anti-clockwise to increase
the temperature.
Temperature Setting
3
Remove all O-rings and seals,
check for damage and replace
if necessary.
Soak all other components in a
suitable solution until
fully de-scaled.
Rinse with clean water.
Use WRAS approved grease on
all seals before re-fitting.
Reverse the steps to
reinstall the valve,
cartridge and handles.
Check all joints
and connections
for any leaks.
Turn the water
supply to
the shower
back on.
Remove the cartridge
retaining nut and
cartridge.
Undo the screw underneath
the shower body to remove
the cartridge.
4
1
56
Riser Installation 23
Assemble
both the top
and bottom
brackets.
Attach the slider, hose
retainer, top and bottom
brackets to the riser rail.
Ensuring its straight, use the
assembled riser to mark the
appropriate positions for
the wall brackets.
Remove the brackets from
the riser. Mark and drill the holes
before securing them to the wall.
Re-attach
the riser to
the secured
brackets.
Connect the
hose to the
shower outlet
and handset,
feeding the
hose through
the hose
retainer.
Place the
handset in
the slider.
1
3
23
45
REMEMBER
To service
your
product!