Broyhill A3TPB-1 User manual

Read all instructions before starting
Clear a flat covered space to begin
Two adults are recommended for assembly
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number in the package
Helpful hints provided along the way
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Regularly check hardware and tighten if necessary
Cleaning Instructions:
Clean periodically by wiping the product with a soft clean cloth.
In the event of the occurrence of jarring sounds during operation,
Stop using the desk and please contact customer service.
Do not use abrasive chemicals for cleaning.
This desk complies with the prescribed safety regulations. Inappropriate use may cause damage to persons and desk.
Please guard this operation manual and pass it on to any future owner!
Do not use power tools.
1
Please make sure all screws are fully tighten before using the product.
Not intended for commercial use.
Please read the operation manual prior to using the desk. It provides you with important information about safety,
use, installation and maintenance of the desk, and thus protecting you and your children and avoiding damage to
the desk.

SET UP AND INSTALLATION
Once the desk is fully assembled and placed in the desired location, level the desk using the adjustable feet. Once the
desk is level, plug the desk into a 100-240 VAC outlet. The desk is then ready to use.
Place the desk in a safe distance from window frames, radiators, furniture etc. so that people do not get stuck.
Do not place any objects above 16.93” (430 mm) underneath the desk.
2
2
SPECIFICATIONS
Make sure that no cables can get jammed.
Input Voltage:100-240Vac 50/60Hz
Duty cycle:10%MAX 2min on 18min off
Dynamic:176LBS（80KGS）
Lift range: 28.35~47.24” (720~1200mm)
Load speed: 25mm/S
Top panel size: 47.24 * 27.56 * 0.98” (1200X700X25mm)

PARTS LIST
HARDWARE LIST
Desk Frame
Top Panel Bracket Foot
Power Cord
Power Supply Handset
X 1 X 1 X 2 X 2
X 1 X 1 X 1
M6x12
Philips head screwdriver is
needed and not included
3
X 14X 8
M8x30
Umbrella Head Bolt
X 1
Allen Bolt
3
X 2
ST4.2x16
Tapping Screw
X 1
M4
Allen Wrench
M5
Allen Wrench

4
STEP 1
x
M4
x
C
C
Use M4 Allen Wrench (4) to attach Bracket (C) to
Desk Frame (A) with Allen Bolt (2). Fully tighten all bolts.

5
STEP 2
x x
Use M4 Allen Wrench (4) to attach Assembled Frame in Step 1
to Top Panel (B) with Allen Bolt (2). Fully tighten all bolts.
B
M4
0

6
STEP 3
xx
Use M5 Allen Wrench (5) to attach Foot (D) to Desk
Frame (A) with Umbrella Head Bolt (1). Fully tighten all bolts.
M5
5
5

7
All screws need to be tightened to obtain optimal stability.
STEP4
G
xx1
Use Phillips Screw Driver (not included) to attach Handset (G) to
Top Panel (B) with Tapping Screw (3). Fully tighten all screws.

8
STEP5
E
F
STEP b
STEP a
Connect the Cord on the Handset (G) and Power Supplier (F)
as shown in STEP a, then insert the Power Cord (E)
in the Power Supplier (F) as shown in STEP b.

9
STEP6
Assembly is now complete.
Do not use this desk or insert the plug before the product is fully assembled.