Bticino 374003 User manual

374001
374003
04/21-01 PC
LE12689AA
BTicino SpA – Viale Borri, 231 – 21100 Varese – Italy – www.bticino.com
Dimensional data
* Recommended height, unless different regulations are specified.
Installation
149 mm
384
mm
60 mm
To ensure proper operation, the Fingerprint Reader (only 374001), must be installed in a location protected from rain.
50 cm
80 °
53 °
50 cm
160 – 165 cm
90 – 130 cm
*
The RJ45 cable must be at least 200 mm long
3
2
1
374001
400 mm
160 mm
58 mm
12 mm
374003
400 mm
160 mm

2
2 mm58 mm
1
3
2
1
2

3
3
Uninstall
6
4
3
5
1
2
*
*
Adjust the tamper screw so that it presses the tamper switch of
the device and activates the anti-theft function in case of removal
sending an alarm to the guard station.
*
4
1
2

4
Front and rear view
1
1
4
7
3
5
2
8
6
9
10
12
11
13
16
15
14
17
13
18
Read carefully before use and keep for future reference
Touching the units with wet hands is forbidden
Using liquid cleaners or aerosols is forbidden
Blocking the ventilation openings is forbidden
Modifying the devices is forbidden
Removing protective parts from the devices is forbidden
Installing the units near liquids and powders is forbidden
Installing the units near heat sources is forbidden
Installing the units near harmful gases, metal dusts or similar is forbidden
Fastening the units on unsuitable surfaces is forbidden
Danger of electrical shock
Risk of devices falling because the surface on which they are installed collapses or inappropriate installation
Switch the power supply OFF before any work on the system
Caution: Installation, conguration, starting-up and maintenance must be performed exclusively by
qualied personnel.
Check that the wall installation has been carried out correctly
Lay out the wires respecting the standards in force
Connect the power supply wires as indicated
Use only the items indicated in the technical specications for any system expansions
Remote operation may cause damage to people or property.
Warnings and consumer rights
Hereby, BTicino S.p.A., declares that the radio equipment type Entrance panel keypad full 374001 / Entrance panel keypad 374003 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.bticino.it/red
Configuration
The device must be congured by software. For software download, installation device documentation and for any
other information, refer to the website.
www.homesystems-legrandgroup.com
Technical data
Voltage 24 Vdc
Maximum consumption 0.65 A
C NC NO contact output 125 Vac/0.5A, 30Vdc/2A
Max. cable section for clamps 0.8 mm²
Operating temperature (- 40) – (+ 70) °C
IP degree of protection 54
IK degree of protection 07
Camera resolution 1080 p
Camera viewing eld angle H= 80°; V= 53°
Face recognition distance during daytime (374001 only) 30-80 cm
Face Recognition Distance at Night (374001 only) 30-50 cm
Badge reader Frequency 13.56 MHz
Badge reader transmission power < 42 dBuA/m @ 10m
1. LED for the shooting eld lighting
2. Camera
3. Light sensor
4. Display 4,3"
5. Badge reader for door lock opening
6. Loudspeaker
7. Backlit keyboard
8. Finger print reader (only 374001)
9. Microphone
10. Locking screws
11. Mounting bracket
12. Tamper switch
13. Connection clamp
14. Reset to the factory settings push button
15. USB Connector (not used)
16. RJ45 Connector (*)
17. Not used
18. Not used
(*)
This device does not support standard POE power supplies, but only POE power
supplies identied with item no. 375002. Connect the cat5/5e/6 FTP or cat5/5e/6
UTP cable with ferrite supplied to the connector
GND
Fire Linkage
Door Open
Connection clamp
GND
Lift Control
system common ground
terminal for RS485 connection FIRE Linkage – GND local door lock release pushbutton connection for realarm system
RS485B terminal A Door OPEN – GND local door lock release pushbutton connection
RS485A terminal B +12V – GND OPEN access control devices power supply
-additional power supply
clamps
OPEN third party access control signal input for door lock opening
(+12Vdc pulse)
+ GND system common ground terminal for third party connection
NC
interlocked contact
SENSE door lock status signal input (dry contact)
C LOCK+ electric door lock connection and control
(12V - 4A impulsive on 3 Ohm maximum)
NO LOCK-