BullFrog 6022 DODO User guide

ASSEMBLY AND INSTRUCTION MANUAL
www.bullfrog-design.com
MODEL 6022 DODO
© 2017 K URT BEI E R &KATI QU I N G E R
DECORATIVE BOX PLEAT
FUNKI - FUNCTIONAL CUSHION
WITH USEFUL PLUG-IN BRACKET
COMFORTABLE
PLUG-IN HEAD ROLL

6022 DODO
© 2017 K URT BEI E R &KATI QU I N G E R
EN: 1. Move the upper part of the cushion towards yourself until the
final position is reached.
EN: 2. Now you are able to move the upper part backwards
until the upper part of the cushion will click into place in the
zero position.
EN: 3. Now put the cushion in the preferred position (e.g. in the
back, seamless side in front and zipper at the bottom). By pulling
the upper part of the chushion towards yourself, you are now able
to choose among 16 raster positions, however you like it.
FUNKI - how it works:
Adjustment of back slant:
1. To adjust the desired position grip
the back from the outside and pull it
carefully towards yourself.
2. To obtain zero position pull the
back carefully beyond the top
position towards yourself and fold
down into zero position (horizontal).
3. From zero position you can easily snap the back into desired position.
Use of back function, functional back, Moba:

6022 DODO
© 2017 K URT BEI E R &KATI QU I N G E R
2 side panels, 1 foot part, 1 headboard (semi-product)
1 loose slip cover for corpus of bed
20 hexagon socket countersunk screws
4 pre-assembled corner connectors (2 x le, 2 x right)
1 laminated wood centre support rail with angle connectors
4 support brackets for corner connectors
2 support brackets for side panels
5 plastic glides
1 plastic supporting foot, small (44-73 mm)
1 plastic supporting foot, large (89-125 mm)
1 Allen key, size: 4 mm
10 Felt gliders, usable for centre support rail (4x), plastic glides (4x),
supporting foot (2x)
Assembly manual
ATTENTION! To ensure secure assembly, please observe the individual steps of instruction!
The furniture should always be mounted in pairs (2 persons)!
Information
CONTENTS
2. For assembly of bed, headboard and foot part or rather
the 2 side panels should be placed at opposite side and
their bottom side at centre (or in upright position towards
flor). The bores should point inwards.
1. Unpack the individual parts of the bed, place them as
shown at picture and check the delivered package contents
for completeness.
Max. 4 cm
Possible heights of mattresses: 16-26 cm
Fig.1 Fig.2
In order to guarantee the function of plug-in head roll and functional cushion Funki,
the mattress should be at one level with bedframe (fig.1) or maximum 4 cm
above the frame (fig.2). Accordingly choose position of angle!

6022 DODO
© 2017 K URT BEI E R &KATI QU I N G E R
3. Set up the head board and
position it at the angle of one side
panel. (fig. le side panel). First of
all, place 2 outer screws and slightly
tighten them. Now it will be easier to
place the other screws. Revise these
steps with the other side panel.
4. Next position the foot part and
screw it as pictured at point 3.
5. Plug in the 4 plastic gliders into
the largest bore of connector
angles (see fig.).
Angular position of
centre support rail
Angular position of
centre support rail
Angular position of
centre support rail
44mm
-
73mm
44mm
-
73mm
89mm
-
125mm
89mm
-
125mm
89mm
-
125mm
89mm
-
125mm
89mm
-
125mm
25mm
Centre support rail
Support angle
Centre support rail
Support angle
Centre support rail
Support angle
Insert depth approx. 26 cm
Centre support rail
Support angle
Insert depth approx. 28,5 cm
Centre support rail
Support angle
Insert depth approx. 31 cm
Insert depth approx. 26,5 cm
Centre support rail
Support angle
Insert depth approx. 24 cm
Insert depth approx. 21,5 cm
Box spring assembly
with plastic glides 2,5 cm

6022 DODO
© 2017 K URT BEI E R &KATI QU I N G E R
6. Mount angles at corner angles at desired height.7. Mount angles at side
panels at desired height.
8. Mount centre support rail at connectors of headboard and foot part at
desired height. If the centre support rail is dicult to mount, slightly loose
the screws of corner angles at foot part. Aer connecting of centre support
rail tighten the screws again.
Attention! The position of angles at centre support rail and corpus of
bed have to be at the same level!
Attention! The mounting of support foot should only
happen aer the bed has been assembled and the final
height of angles and the alignment of centre support rail is
set. Aer mounting, it is dicult to remove the support foot.
9. Aer you decided the position of centre support rail and angles, stick
the felt gliders at pictured position.
Angular position A
Angular position B

6022 DODO
© 2017 K URT BEI E R &KATI QU I N G E R
2
56
1
4
3
Detailed assembly instruction:
Insert depth = 23,5-32,5 cm
At any corner angle (1) a3,5 cm height plastic glide feet (2) has to be
plugged 12,5 mm into the bore.
The support bracket (3) and the centre support rail (4) have to be
connected at the same level.
10. Support foot:
Support feet for centre support rail:
use the small support foot (5) for the lower
attachment points, the large foot (6) for the
upper attachment points.
Aer you have decided a height, press the
suitable supporting foot tight into the hole of
centre support rail from below and adjust the
floor height.
Large Small
12. Pay attention that the corner seams are exactly oriented at mitre and
the parts of box pleat hang down exactly at the 4 edges.
Aer you have placed the cover properly onto the corpus, remove
the velcro (so side strap) carefully and fix the cover.
Plug in of cushion and head roll: aer assembly
of bed with slatted frame/box spring system
and mattress, you can insert the bracket of
cushion/head roll between the covered metal
bar and the corpus (example at picture is
shown without mattress)!
11. Place slip cover (with velcro part inwards)
onto corpus of bed.
(Do not yet remove the so side strap of velcro!)
Keep all documents relating to the purchase of your furniture carefully, even beyond the legal warranty period of 2 years. You will
find all important information in your product folder and also on our website www.bullfrog-design.com