BullFrog Yumi 0719 User guide

www.bullfrog-design.com
26.05.2021
Functional back and armrests
are completely foldable
...up to a comfortable relax lounger Due to lateral seat adjustment arises
a useful clipboard
ASSEMBLY AND INSTRUCTION MANUAL
© 2019K U RT B E I E R & KATI Q U I N G E R
MODELL 0719 YUMI

ATTENTION!
DON`T SIT ON BACK OR ARMREST EXCEPT THEY ARE AT LOWEST POSITION.
Use of back- and armrest function
Adjustment of armrest slant:
1. To adjust the desired position grip the armrest from the outside and pull it carefully into your direction.
3. From zero position you can easily snap the armrest into desired position.
2. To obtain zero position pull the armrest carefully beyond the top position into your direction and fold down
into zero position.
To adjust back, proceed the same way.
Sitting
0719 YUMI
© 2019 K URT BEI E R &KATI QU I N G E R

Motorised seat adjustment:
TRANSFORMER
A
Power supply
Lying
Relaxing
1. Connect cable A (fixed at seat element) to provided transormer and plug it into socket.
2. Press button B und C at remote control to move seat continuously to the right or to the left.
A
To avoid traces of usage at cover material, seat should (as possible) only be adjusted
when back and armrest are folded up (like fig. above).
At types with manual adjusment possibilities the seat cushion can be mooved back
and forth in the direction of the arrow .
ATTENTION!
TRANSFORMER HAS TO
BE SITUATED OUTSIDE
OF THE SOFA!
C
B
0719 YUMI
© 2019 K URT BEI E R &KATI QU I N G E R

Delivery condition: already synchronised December 2017
B
C
A
1. Press pairing buttons Aat receiver 2 x until the LED
indicates. The pairing process is active for about 10 seconds.
2. Press simultaneous button B and C at remote cont-
rol until the green LED starts to flash. The flashing confir-
mes a successful pairing process.
Note:
For the pairing prozess the distance between transmitter
and receiver should be less than 2 metres.
Motorised seat adjustment - Programming of transmitter and receiver
The programming is completed, the transmitter is now ready for operation. If the motor doesn´t start while pressing,
release the button and press again. If necessary retry the process.
Transmitter
Brief instruction, Pairing-Method:
Should a new start-up of remote control be necessary the wireless communication with the
control/motor must be established. Proceed as follows:
Receiver
LED
Put drive systems into operation successively, don`t operate several systems simultaneous. Otherwise the
remote control cannot be assigned clearly by control/motor.
0719 YUMI
© 2019 K URT BEI E R &KATI QU I N G E R

FUNKI - how it works!
1. Turn connector ratchet 1 of element A to the outside.
2. Firmly push together part A and B, until metal guides 2 catch into guides 1.
3. In case of dismounting lift part B with the metal guides 2 and pull away.
Mounting of connectors
A B
12
seam
zipper
1. Take the cushion at its upper side
and put the cushion on your knees
with the zipper on the bottom. The
seamless side faces you.
2. Move the upper part of the cushion
towards yourself until the final position
is reached.
3. Now you are able to move the upper
part backwards until the upper part of
the cushion will click into place in the
zero position.
4. Now put the cushion in the preferred
position (e.g. in the back, seamless side
in front and zipper at the bottom).
By pulling the upper part of the chushion
towards yourself, you are now able
to choose among 16 raster positions,
however you like it.
0719 YUMI
© 2019 K URT BEI E R &KATI QU I N G E R