BullFrog 0920 PIROU User guide

Individually designable sofa with
dual function in back and armrest
(example with high armrest)
Armrests can be folded down
to form a lounger.
As a single lounger or...
... cosy double couch
(example with low armrest).
ASSEMBLY AND INSTRUCTION MANUAL
www.bullfrog-design.com
28.05.2021
MODEL 0920 PIROU
© 2020 K URT BEI E R &KATI QU I N G E R
Head-rest
Functional
back
Armrest
flap
Functional
armrest
Sofa 2,5-Seat with high armrest
240DFH
Sofa 2,5-Seat with low armrest
240FH

Proceed in the same way to adjust the armrest flap.
Adjustment of head-rest (or armrest flap):
1. To adjust the desired position grasp the head-rest from the outside and pull it slightly towards yourself.
3. From zero position you can easily snap the head-rest into desired position.
2. To obtain zero position pull the head-rest slightly beyond the top position towards yourself and fold it down
into zero position.
Functional back
Armrest flap
ATTENTION! DON`T SIT ON BACK AND ARMREST.
Functional AR
0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
Head-rest

0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
Proceed in the same way to adjust the back.
At the motorised version, the back is continuously adjustable by means of a remote control. See: Use of the
motorised back function.
Use of the manual back and armrest function:
1. To adjust the desired position grasp the armrest (or back) from the outside and pull it slightly inwards
(towards yourself) to adjust the desired position.
3. From zero position you can easily snap the armrest (or back) into desired position.
2. To obtain zero position pull the armrest (or back) slightly beyond the top position towards yourself and fold it
down into zero position.
ATTENTION! DON`T SIT ON BACK AND ARMREST.
Functional back
Armrest flap
Functional AR
Head-rest

A
0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
Use of the motorised back function:
1. Insert the plug A into the charging socket at the bottom of the sofa and then the transformer into the socket.
2. By pressing the switch buttons B and C at remote control, the back can be moved continuously to the
required position.
The 2 remote controls are located at the back (outside)!
POWER SUPPLY
Charging socket
Charging socket
Plug
C
B
ATTENTION! DON`T SIT ON BACK AND ARMREST.
Pockets for remote controls
Armrest
Back
TRANSFORMER
ATTENTION!
TRANSFORMER HAS TO
BE SITUATED OUTSIDE
OF THE SOFA!
Rechter Rücken = rechts
Linker Rücken = links

Use of rotation function
Adjusting the seat to a lounger:
1. To obtain the lying position, grasp the armrest from the outside in the raised position and lift it slightly.
2. In the raised position, turn the seat forwards and let it snap back into place.
3. The foot flap (armrest flap) can now be folded up or down (see Adjusting the armrest flap).
4. To get back into the seat position, lift the footrest (armrest) slightly and turn the seat back to the basic position.
0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
1. 2.
ATTENTION! DON`T SIT ON FOOT PART (ARMREST).

0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
Delivery condition: already synchronised December 2017
B
C
A
1. Press pairing buttons Aat receiver 2 x until the LED
indicates. The pairing process is active for about 10 seconds.
2. Press simultaneous button B and C at remote cont-
rol until the green LED starts to flash. The flashing confir-
mes a successful pairing process.
Note:
For the pairing prozess the distance between transmitter
and receiver should be less than 2 metres.
Motorised back function - Programming of transmitter and receiver
The programming is completed, the transmitter is now ready for operation. If the motor doesn´t start while pressing,
release the button and press again. If necessary retry the process.
Transmitter
Brief instruction, Pairing-Method:
Should a new start-up of remote control be necessary the wireless communication with the
control/motor must be established. Proceed as follows:
Receiver
LED
Put drive systems into operation successively, don`t operate several systems simultaneous. Otherwise the
remote control cannot be assigned clearly by control/motor.

Montage / Assembly:
Info:
1. Position the elements at the place supposed to stay and remove the foil and the cardboard.
2. Unpack the small parts and put them in front of you.
2 x Threaded pin (a) 2 x Toothed lock washer (b)
4 x Bolt (g) for feet
2 x Cap nut (c)
Short side
Short side
0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
ATTENTION! To ensure secure assembly, please observe the individual steps of instruction!
The furniture should always be mounted in pairs (2 persons)!

3. Tilt the element forwards. Use a suitable support to avoid damage to the cover or your floor.
4. Remove the transport lock screws (F) 1 Spax screw (F) and 1 washer (d) per side). The washer (d) will
be used again in the following step.
0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
d
FF

5. Now screw the threaded pin (a) with the short side instead of the Spax screws (F) into the hole. First
push the washer (d) and then the toothed lock washer (b) over the threaded pin (a) and tighten
everything with the cap nut (c).
6. Proceed the same way at the oder side.
7. Unscrew the 4 screws (h) from the transport protection. Now remove the transport protection by lifting the
element slightly and pull the transport protection away over the feet towards the front (towards you).
0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
db
a
c
h=2x
h=2x
h=2x

8. Now screw the 4 bolts (g) (2 per foot) back into the feet.
9. Place the element back on its feet.
0920 PIROU
© 2020K URT BEI E R &KATI QU I N G E R
g
g