Burda NOGLARE NRCAC065 User manual

1
ASSEMBLY and OPERATING INSTRUCTIONS
NOGLARE Series
NRCAC065 ( IP20 ) NRCAC065 - 1 ( IP20 )
NRCJC130 ( IP20 ) NRCJC130 - 1 ( IP20 )
NRCKC195 ( IP20 ) NRCKC195 -1 ( IP20 )
NRCAC065
NRCJC130
NRCKC195

2
INSTALATION AND USE INSTRUCTIONS OF CERMIC, ELEKTRIC
INFRARED HEATERS: NRCAC065, NRCJC130, NRCKC195
NOTE: Please read the following instruction carefully before using the appliance for
the first time, for your own safety and to ensure correct use.
All electrical installations and connections must be carried out in accordance with local safety
regulations and standards. If in any doubt, please consult an authorized personnel of power
engineering service.
CAUTION: The Infrared Heaters must be earthed.
Ceramic Heaters are intended for using Indoor in enclosed spaces and open, covered areas.
The 3m power cord with Schuko Plug enables connection to an electric socket with a mid- or
slow-blow protection „B or C”10A at least and with an earthing pin.
INSTALLATION OF INFRARED HEATERS: NRCAC065, NRCJC130, NRCKC195
Recommended positioning to hang up the reflectors
Minimum distances of hanging a TERM2000 Heater from a floor, ceiling and side walls
depend on the reflector type (power).
Refer to the below table and scheme showing the parameters:
Model: „a”min „b“min „c“min
NRCAC065, NRCAC065 -1 2,0 m 0,3 m 1,0 m
NRCJC130, NRCJC130 -1 2,0 m 0,5 m 1,0 m
NRCKC195, NRCKC195 -1 2,0 m 0,5 m 1,0 m
NOTE:
In the reflector code (i.e. NRCAC) the first 4 letters stand for: Ceramic Heat Reflector, the forth letter
stands for configuration and q-ty of emitters, the fifth letter ”C”stands for a version of color, the
consecutive numerals define the power as follows: 065 = 650W, 130 = 1300W, 195 = 1950W.
Number -1 means black color RAL9005. No Number means white color RAL9010.
COUTION: The reflectors must not be mounted near curtains and other flammable items.
Never place the reflectors directly under a wall socket!

3
NOTE:
A power cord must not come into contact with housing of reflector.
To avoid risk of danger, in case of damage of reflector power cord, immediately
replace it referring to manufacturer or a qualified electrician or a customer service.
Any replacement of the original power cord supplied with the reflector is forbidden.
When the appliance becomes no longer usable, it must be collected and utilized according to valid
local regulations.
INSTALLATION:
The reflectors have been designed for wall mounting by using a metal holder supplied by a
producer. Screw on an arm of the holder to the wall (with two holes) using dowels and
screws at diameters 8 –12 mm and at length 60-80mm, depending on type (weight) of
reflector.
Set the tilting angle of the reflector toward a floor by blocking the jointing bracket in the
required position (usually 45o ). Housing of the reflector should be positioned in parallel
toward a wall surface and a ceiling as well should to secure the horizontal position of the
ceramic element –it is recommended operation position for the heat radiator.
Maintenance
NOTE : Before cleaning the appliance remember to
·Ensure that the heater is disconnected from the power supply system!
·Cool down the heater
·Clean an emitter with soft cloth moistened with water, other elements clean by
„blowing away”gathered dust.
·Do not use any abrasive or caustic clearing agents.
·Never immerse the appliance in water. Danger to life!
Technical data:
Rated voltage: 230V/50 Hz
Rated output: 650/1300/1950 W
Dimensions: 36/61/86 x 12 x 15,5 cm
Weight: 1,8/2,3/2,8 kG
Protective system: IP 20
We wish you a lot of satisfaction from operating the appliance.
Further informations you can find on the web:
www.NoGlare.de