Burda PERFECTCLIME RELAX GLASS FRAME IRA IP65... User manual

RELAX GLASS FRAME
IRA IP65(1500W/1800W)
EINBAU-MONTAGEANLEITUNG –SCHRAUBENBEFESTIGUNG
FLUSH-MOUNTED INSTALLATION MANUAL –SCREW FIXING
MANUEL D'INSTALLATION ENCASTRÉ –VIS DE FIXANTION
MANUALE DI INSTALLAZIONE DA INCASSO –FISSAGGIO A VITE
MANUAL DE INSTALACIÓ N EMPOTRADO –FIJACIÓ N DE TORNILLO
INDBYGNINGSINSTALLATIONSMANUAL –SKRUEFASTGØ RELSE
INBYGGD INSTALLATIONSMANUAL –SKRUVFÄ STNING
INNEBYGD INSTALLASJONSMANUAL –SKRUEFESTE
UPPOASENNETTAVA ASENNUSOHJE –RUUVI KIINNITYS
Irrtum und technische Ä nderungen vorbehalten ・Subject to errors and technical changes ・Sous reserve d‘erreurs et de
modifications techniques ・Excepto erro ou alteracao tecnica ・Salvo error o modificacion tecnica ・Fejl og tekniske
æ ndringer forbeholdt ・Fel och tekniska ändringar reserverade ・Feil og tekniske endringer reservert ・Virheet ja tekniset
muutokset on varattu!
Burda Worldwide Technologies GmbH –Rudolf-Diesel Straße 18 –65760 Eschborn
T: [phone] - F:[phone] - [email protected] –www.burdawtg.de

FLUSH MOUNTED INSTALLATION FOR BRELGF1500-1800X:
Dear Customer,
please read the following information carefully before using
the appliance for the first time for your own safety and to
ensure correct use and installation.
DESIGNATED USE:
Outdoor areas.
INFORMATION:
• The Flush Mount Enclosure is an ideal way to neatly install
the heater into a ceiling. Flush mounting can be used with
any building grade ceiling materials.
• Maximum mounting heights should be strictly followed,
otherwise the performance of the units may be reduced.
The enclosure is manufactured from stainless steel.
WARNING:
Depending on material and design of ceiling structural
elements, the appliance must be secured with the
correct fasteners. The total weight of the heater and the
kit are up to 8 kg, the installation location must be able
to hold 5 times the weight of the heater and the kit.
NOTE:
The bracket (no.2) is specially designed for flush-mounted
installation packed together with the frame (no.3). Please
don’t use the bracket used for wall-mounted installation for
the flush-mounted installation.
• Ensure all clearances detailed in the figure below are
strictly followed (dimensions in mm):
• The minimum distance between the back of the enclosure
and any building material is 150 mm.
• The heater must not be located immediately below a
socket-outlet. The heater must not be located in front of a
socket-outlet.
• The socket must be located outside the physical footprint
of the units to minimize heat build-up behind the heater.
• The minimum distance between the sides of the enclosure
and any support structure is 100mm.
The minimum distance between adjacent enclosures is
200mm.
Bracket for flush-mounted
installation
Bracket for wall, or
ceiling installation
GB
150mm Min.
socket
Ceiling joist
Batten
100mm
Minimum
100mm
Minimum
200mm
Minimum
Between
Enclosures

INSTRUCTION
1. Please check if following accessories are complete before installation:
2. Hole cut-out dimensions on the ceiling is shown in figure below:
3. Make a batten frame as per the dimension shown below:
Part no. Part name Qty
①Heater 1
②Bracket for flush-
mounted 2
③Cabinet 1
④Screw ST5*30mm 4
⑤Screw M5*10mm 4
GB
4
3
2 2
15
956±1.5mm
210±1.5mm
95 6 mm
23 0 mm

4. Fix the bracket (no.2) on the back of the heater, as per the dimension shown in the figure below:
5. Lock the bracket by tightening the 4 screws (M5*10mm) show in the figure below:
6. Fix the frame on the ceiling and fix it by 4 pcs ST5*30mm (not supplied) screws.
GB

7. Connect the heater to the power source, ensure the power is OFF. Ensure the power cable will not lay on the back of the
heater.
8. Lift the heater into the frame, ensuring the brackets go through the cut holes on the top of the frame shown in figure below:
9. Move the heater to the left direction and then drop in, ensuring the brackets place rightly on the hanger. Gently shake the
heater to ensure that it is securely mounted.
GB