Burg Wächter secuENTRY Home ENTRY 5000 CYL User manual

www.burg.biz
BURG-WÄCHTER KG
Altenhofer Weg 15
58300 Wetter
Germany
Master Operating Instructions
secuENTRY Home
ENTRY 5000 CYL
Contents index
English 2
Further languages at:
www.burg.biz
Dear Customer,
Thank you very much for deciding on the secuENTRY 5000 CYL.
The system was developed in Germany according to the most
modern technical capabilities and fulls the latest high safety
requirements.
The secuENTRY 5000 CYL electronic cylinder can be easily
installed in any door with a prole cylinder lock, up to a door
thickness of 118 mm (59/59 mm, measured in the centre of the
forend screw). No drilling or laying of cables is required and it
is ideally suited for both new installations and retrotting. The
secuENTRY 5000 CYL can be tted to house and interior doors.
The secuENTRY 5000 CYL is setup and operated using the free
smartphone app secuENTRY KeyApp*. The transmission is wire-
less, the cylinder uses the modern Bluetooth 5.2 standard.
*Alternatively, the cylinder can also be operated via the PIN keypad ENTRY 7711
Keypad PIN or the radio key ENTRY sE-Key 7713 (both available separately).
ThesecuENTRY KeyApp, however, is always required for the setup.
Important:
Please read the entire operating instructions before you
start the installation.
We hope you enjoy your new locking system!
!
Foreword
en
en

2 I Englsih secuENTRY HOME 5000 CYL
Cylinder unit power supply 2x Mignon LR6 AA Alkaline
Permitted ambient conditions -15 °C/+50 °C / up to 95 %
relative humidity (non-condensing)
Radio standard Bluetooth 5.2
Range Approx. 4 m
Number of access media 1 user code*+ 5 sE-Keys** or 5 KeyApp
connections
*User code as opening medium can only be used in conjunction with the
PIN keypad ENTRY 7711 Keypad PIN (available as an option).
** Radio key ENTRY sE-Key 7713 available as an option.
Fig. 4
Fig. 6 Fig. 7
Fig. 2
Fig. 3
Fig. 5
Technical details
QR code/Administrator code
secuENTRY 5000 CYL commissioning
QR
The QR code (I) is required later when setting up
the cylinder using the BURG-WÄCHTER KeyApp
(Fig. 2).
The cylinders are delivered with a factory-
assigned random administrator code (II),
therefore a code change is not mandatory (Fig. 2).
To setup the secuENTRY 5000 CYL, you
must rst download the secuENTRY
KeyApp. This can be found in the App
Store and Google Play Store (Fig. 3).
Once you have successfully registered,
you can start setting up the secuENTRY
5000 CYL.
Open the main menu (Fig. 4).
In the following menu, tap on "Device
Setup" (Fig. 6). From here you can add
and setup secuENTRY units to the app.
Use the selection menu displayed and
tap on "secuENTRY Proly Cylinder" to
setup your secuENTRY cylinder (Fig. 7).
Tap on the menu item
"secuENTRY setup" (Fig. 5).
A list is displayed in which cylinders
that have already been registered can
be found at a later date. This list is,
of course, empty when installing the
secuENTRY KeyApp and setting up a
cylinder for the rst time.
Add a new cylinder by tapping on the
"+" in the top right-hand corner
(Fig. 8).
Attention:
The QR code and the factory-assigned
administrator code are not stored by
BURG-WÄCHTER. Recovery is not possible
if the codes are lost. Please store the sticker
shown above in a safe place. In addition, it is
recommended that you take a photo of the
sticker and archive it digitally.
secuENTRY
KeyApp
1
2
3
4
5
6
7
Fig. 8
Set contents
IENTRY Home 5000 CYL Cylinder
II Forend screw
III Hexagon spanner SW2
IV Quick Start Guide plus
warranty and
disposal instructions
!
Fig. 1
I
II
Fig. 1
I
II III
IV

3 I Englsih secuENTRY HOME 5000 CYL
Fig. 9
Fig. 11
Fig. 13
Fig. 10
Fig. 20Fig. 19
Fig. 12
Fig. 14
A prompt will appear asking you to
scan the QR code provided using your
smartphone camera. The QR code is on
the sticker enclosed in the packaging
(see small g.).
Tap on "Continue" (Fig. 9). You may be
asked to conrm the app's access to the
camera. The camera's picture window
will then open (Fig. 10). Scanthe
QRcode.
A message appears containing data
about your cylinder, conrm this with
"OK" at the bottom right (Fig. 11).
The following window gives you the op-
tion of assigning a name to the cylinder.
If several cylinders are used, it is recom-
mended to name the cylinder in a way
that you can directly recognise where
the cylinder is located or attached.
Conrm the name with "OK" (Fig. 12).
A message appears informing you that
you can change your administrator
code. As you received a randomly gen-
erated administrator code at the time of
delivery, this step is optional. Use "SKIP"
to bypass it (I), (Fig. 13).
Note: The administrator code can be
changed at any time at a later date.
Instructions on how to do this can be
found in the chapter "Change adminis-
trator code" on page 3.
Should you wish to change the admin-
istrator code immediately during setup,
tap on "CONTINUE" (II) (Fig. 13) for the
corresponding request. This then leads
directly to the "Change administrator
code" function, which is also described
in the following chapter on page 3, at
point 5.
Your secuENTRY cylinder is now fully
setup. It will now appear in the list of
setup cylinders (Fig. 14).
8
9
10
11
12
13
14
P
QR
I
I
II
II
!
Proceed as follows to delete a cylinder:
Open the main menu (Fig. 15).
Tap on the menu item
"secuENTRY setup" (Fig. 16).
1
Change administrator code
Fig. 15 Fig. 16
2
Fig. 17 Fig. 18
In the following menu, tap on
"Device Setup" (Fig. 17).
Use the selection menu displayed and
tap on "secuENTRY Proly Cylinder"
(Fig.18).
A list with setup cylinders is displayed.
Select the required cylinder (I) and tap
on "Set Admin Code" (II) (Fig. 19).
Enter the pre-existing administrator
code, followed by entering your desired
administrator code twice (I). Conrm
the entries with "CHANGE CODE" (II)
(Fig. 20).
Tip: The entry is concealed. Tap the eye
symbol on the right side to visualise
and check the entry.
Attention: Do not select simple codes
that are easy to guess (e.g. 1-2-3-4-5-6).
Also, do not select any personal infor-
mation (e.g. birthdays) or other infor-
mation that can be easily be deduced
by persons who know the user.
Press the "SKIP" button to cancel the
process, the administrator code will not
be changed (III) (Fig. 20).
A message is displayed if the change
has been made successfully.
3
5
7
6
4
I
II
I
II
III
!
!

4 I Englsih secuENTRY HOME 5000 CYL
Fig. 25
A list with setup cylinders is displayed.
Swipe the entry of the cylinder you
wish to delete to the left (I) and tap on
the "DELETE" eld (II) that appears on
the right (Fig. 25).
5
I
II
Proceed as follows to delete a cylinder:
Open the main menu (Fig. 21).
Tap on the menu item
"secuENTRY setup" (Fig. 22).
1
Delete cylinder
Fig. 21 Fig. 22
2
Fig. 23 Fig. 24
In the following menu, tap on "Device
Setup" (Fig. 23).
Use the selection menu displayed and
tap on "secuENTRY Proly Cylinder"
(Fig. 24).
3
4
Create user
Open the main menu (Fig. 26).
Tap on the menu item
"secuENTRY setup" (Fig. 27).
Tap on "User administration"
in the submenu (Fig. 28).
A list of users that have already been
created is displayed.
Create a new user by tapping on
the "+" in the top right-hand corner
(Fig. 29).
1
2
3
4
Fig. 28 Fig. 29
Fig. 26 Fig. 27
Create user and assign access medium
There are various access media available to open your door. Including opening with a user-dened
code*, the sE-Key** radio key and the KeyApp itself.
Once you have created a secuENTRY cylinder in the KeyApp, you are the administrator of this
cylinder. This function allows you to create users for yourself and others and to assign one access
medium per user.
Attention: For the ENTRY Home 5000 CYL cylinder, a maximum of six users can be created, each
with one access medium. One user code*and ve sE-Keys** or ve KeyApps as electronic keys.
*User code as opening medium can only be used in conjunction with the PIN keypad ENTRY 7711 Keypad PIN (available as an option).
** Radio key ENTRY sE-Key 7713 available as an option.
!

5 I Englsih secuENTRY HOME 5000 CYL
Create user – User code
Enter the rst name and surname of the
user you wish to register (I) (Fig. 30).
This section allows you to set up a user
code, a radio key sE-Key or another
smartphone as an electronic key (II)
(Fig. 30).
Proceeding from this menu view, look
at the following chapters and continue
with the desired access medium.
Note: Only one access medium is
possible per user.
1
2
3
4
5
Fig. 30
Fig. 31
Note: A user code can only be used as an
opening medium in conjunction with the
ENTRY 7711 Keypad PIN, which is available as
an option.
Enter a user-dened code (I) (Fig. 31).
Tip: The entry is concealed. Tap the eye
symbol on the right side to visualise and
check the entry.
Attention: Do not select simple codes that
are easy to guess (e.g. 1-2-3-4-5-6). Also, do
not select any personal information (e.g.
birthdays) or other information that can be
easily be deduced by persons who know
the user.
Next, assign a cylinder by tapping it in the list
of cylinders already registered (II) (Fig. 31).
Save your settings by tapping the disk
symbol in the top right-hand corner (III).
The user has now been assigned the user
code and the selected lock within the
KeyApp (Fig. 31).
The programming process must be started
so that the cylinder also receives this
information. The corresponding description
can be found in the chapter "Programming/
Updating the cylinder" on page 9.
!
I
I
II
II
III
!
!
!
Create user – Radio key sE-Key
1
2
3
4
Fig. 32
Fig. 34
Fig. 33
Fig. 35
Note: The radio key "ENTRY sE-Key 7713"
is available separately from specialist
retailers. You can connect a maximum
of ve radio keys.
A radio key is connected by scanning
the QR code enclosed with the sE-Key.
Tap the QR code symbol in the "Enter
sE-KEY" line in the user menu (Fig. 32).
You may be asked to conrm the app's
access to the camera. The camera's
picture window will then open (Fig. 33).
Scan the QR code.
A message appears containing data
about your radio key, conrm this with
"OK" at the bottom right (Fig. 34).
Next, assign a cylinder by tapping it in
the list of cylinders already registered
(I) and save your settings by tapping
on the disk symbol at the top right (II)
(Fig. 35).
The user has now been assigned the
radio key and the selected lock within
the KeyApp. The programming process
must be started so that the cylinder
also receives this information. The
corresponding description can be
found in the chapter "Programming/
Updating the cylinder" on page 9.
!
QR
I
II

6 I Englsih secuENTRY HOME 5000 CYL
Create user – KeyApp as an electronic key
Option 1: QR code
1
2
3
4
5
6
Fig. 36
Fig. 38
Fig. 37
Fig. 39
The KeyApp allows you to open the lock with the help of another smartphone. The installation
has two dierent options for this method of opening:
Option 1: via a QR code
Option 2: via a CSV le
Instructions for each option are given below. It doesn't matter which of the two procedures you
choose, they both lead to the same result.
Note: You can connect a maximum of ve smartphones as electronic keys.
Note: To simplify the explanation, the administrator or their smartphone is referred to below
as 'smartphone A' and the smartphone of the user who is to receive opening authorisation is
referred to as 'smartphone B'.
Smartphone B:
First, download the secuENTRY KeyApp
and register.
Open the main menu (Fig. 36).
Tap on the menu item "KeyApp setup"
(Fig. 37).
Tap on "Key functions" (Fig. 38).
In the next menu, tap on "QR code"
(Fig.39), after which a QR code is dis-
played on the entire screen.
Leave the QR code displayed on the
screen and put the smartphone B
aside for a moment. The next steps are
performed on smartphone A.
!
!
1
2
3
4
5
Smartphone A:
The QR code displayed on smartphone
B can now be scanned via the app on
smartphone A.
Tap the QR code symbol in the "Enter
KeyApp" line in the user menu (Fig. 40).
You may be asked to conrm the app's
access to the camera. The camera's
picture window will then open (Fig. 41).
Scan the QR code on the smartphone
B screen.
A message appears containing data
about the KeyApp on smartphone B,
conrm this with "OK" at the bottom
right (Fig. 42).
Next, assign a cylinder by tapping it in
the list of cylinders already registered
(I) and save your settings by tapping
on the disk symbol at the top right (II)
(Fig. 43).
The user has now been assigned an-
other KeyApp as an electronic key and
the selected lock within the KeyApp.
The programming process must be
started so that the cylinder also receives
this information. The corresponding
description can be found in the chapter
"Programming/ Updating the cylinder"
on page 9.
Fig. 40
Fig. 42
Fig. 41
Fig. 43
I
II

7 I Englsih secuENTRY HOME 5000 CYL
Option 2: CSV le
1
Fig. 44 Fig. 45
Smartphone B:
First, download the secuENTRY KeyApp
and register.
Open the main menu (Fig. 44).
Tap on the menu item "KeyApp setup"
(Fig. 45).
2
3
4
5
6
7
Fig. 46
Fig. 48
Fig. 47
Tap on "Key functions" (Fig. 46).
Tap on "Send again" in the next menu
(Fig. 47).
An email is then automatically created
and opened in your email program. The
attachment contains a registration le
with the extension ".csv" (Fig. 48).
Send the email to an email address that
can be retrieved by smartphone A.
Put smartphone B aside, and the rest
of the procedure will be performed on
smartphone A.
1
2
3
4
5
6
7
Smartphone A:
Temporarily store the le received
from smartphone B on smartphoneA.
The le can be deleted again after
programming.
Tap on "CSV" in the user menu at the
top right (Fig. 49).
Select the CSV le that you received by
email from smartphone B (I). Conrm
the selection at the top right with the
tick (Fig. 50).
The data is now recorded in the
KeyApp.
Next, assign a cylinder by tapping it in
the list of cylinders already registered
and save your settings by tapping on
the disk symbol at the top right
(Fig. 51).
The user has now been assigned
another KeyApp as an electronic
key and the selected lock within the
KeyApp. The programming process
must be started so that the cylinder
also receives this information. The
corresponding description can be
found in the chapter "Programming/
Updating the cylinder" on page 9.
The CSV le temporarily stored on
smartphone A can now be deleted.
Fig. 49 Fig. 50
Fig. 51
I
I
II
II

8 I Englsih secuENTRY HOME 5000 CYL
Changing the user access medium
1
2
Proceed as follows if you wish to
change an opening medium assigned
to a user:
Open the main menu (Fig. 52).
Tap on the menu item
"secuENTRY setup" (Fig. 53).
Tap on "User administration" in the
submenu (Fig. 54).
In the list of created users, tap the user
for which you want to change the user
code (Fig. 55).
The data view for the required user
appears (Fig. 56).
Proceeding from this menu view, look
at the following chapters and continue
with the desired access medium.
3
4
5
Fig. 54 Fig. 55
Fig. 52 Fig. 53
Fig. 56
Changing the user access medium - User code
Changing the user access medium - Radio key sE-Key
Delete the entry of the relevant line
and, if required, enter a new user-
dened code (I) (Fig. 57).
Tip: The entry is concealed. Tap the eye
symbol on the right side to visualise
and check the entry.
Attention: Do not select simple codes
that are easy to guess (e.g. 1-2-3-4-5-6).
Also, do not select any personal infor-
mation (e.g. birthdays) or other infor-
mation that can be easily be deduced
by persons who know the user.
Save your settings by tapping the disk
symbol in the top right-hand corner (II)
(Fig. 56).
Note: It is also possible to assign a
dierent access medium instead of a
new user code. To do this, follow the
chapter "Create user and assign an access
medium" on page 4.
Tap the relevant line (Fig. 58) to delete
the entry.
A message will then appear prompting
you to conrm (Fig. 59). Tap on "OK".
Now you can enter another sE key or
another access medium. To do this,
follow the chapter "Create user and
assign an access medium" on page 4.
1
1
2
3
2Fig. 57
Fig. 59Fig. 58
I
II
!
!
!

9 I Englsih secuENTRY HOME 5000 CYL
Changing the user access medium - KeyApp as electronic radio key
Tap the relevant line (Fig. 60) to delete
the entry.
A message will then appear prompting
you to conrm (Fig. 61). Tap on "OK".
Now you can enter another another
KeyApp as an electronic key or another
access medium. To do this, follow the
chapter "Create user and assign an
access medium" on page 4.
1
2
3
Fig. 61
Delete user
1
2
Proceed as follows to delete a user:
Open the main menu (Fig. 60).
Tap on the menu item
"secuENTRY setup" (Fig. 61).
Tap on "User administration" in the
submenu (Fig. 62).
A list of users is displayed. Swipe the
entry of the user you wish to delete to
the left (I) and tap on the "DELETE" eld
(II) that appears on the right (Fig. 63).
3
4
Fig. 62 Fig. 63
Fig. 60 Fig. 61
Programming/updating the cylinder
The cylinder must be programmed
accordingly so that the registered users
can now open the lock with the stored
opening options. Program the cylinder
as follows:
Open the main menu (Fig. 64).
Tap on the menu item
"secuENTRY setup" (Fig. 65).
Tap on "Programming" in the submenu
(Fig. 66).
The list of programming les appears.
This is where the required changes are
generated in programming les and
collected for sending to the cylinder. By
default, the list is empty because there
is no collection. If there are still earlier
programming les in the list, delete
them by sliding the respective entry
from right to left (Fig. 67).
Tap the "+" at the top right to add your
required changes or the corresponding
cylinder to the list (Fig. 68).
1
2
3
4
5
Fig. 66
Fig. 68
Fig. 64 Fig. 65
Fig. 60
I
II
Fig. 67

10 I Englsih secuENTRY HOME 5000 CYL
A message appears stating that the
programming le has been generated.
Conrm the name with "OK" (Fig. 71).
Select the programming le that is
now in the list (I) and tap on "Program
(update) unit" (II) (Fig. 72).
Note: If you have generated several
programming les for several cylinders,
please only select the cylinder within
the Bluetooth range of which you are
located.
Once again you will be prompted to
enter your administrator code (Fig. 73).
After entering the code (I), keep your
smartphone close to the cylinder (max.
2 m) and tap on "START" to start pro-
gramming (II).
The loading window indicates that
programming has started and the
current status of the programming
(Fig.74).
As soon as the programming has been
completed successfully, you will receive
a corresponding feedback. Conrm the
name with "OK" (Fig. 75).
If the process failed, repeat the steps
starting from step 6.
9
10
12
13
14
15
11
Fig. 73
Fig. 75
Fig. 74
Fig. 71 Fig. 72
I
I
II
II
Opening the secuENTRY lock
Fig. 76
Proceed as follows to open the
ENTRY Home 5000 CYL cylinder and
consequently also the door:
Open the secuENTRY KeyApp and press
the "GET ACCESS" button in the middle
(Fig. 76).
Note: The secuENTRY KeyApp is
programmed so that when more than
one cylinder is used, it automatically
adjusts to the cylinder that is within the
shortest distance of the smartphone.
Each cylinder can be opened by
pressing the "Get Access" button.
The cylinder is now released and the
lock can be opened (g. 77) or locked
(Fig. 78).
Note: Depending on the door stop, the
direction of rotation may be reversed.
1
2
!
!
!
Fig. 78
Fig. 77
Select the cylinder for which you have
set up changes (I) (Fig. 69).
Note: If you have several cylinders and
have created changes for each, please
only select the cylinder within the Blue-
tooth range of which you are located.
Then tap on "PROG.FILE" (II) at the top
right (Fig. 70).
You will then be prompted to enter
your admin code (I) and conrm with
"OK" (II) (Fig. 70).
6
7
8
Fig. 69 Fig. 70
I
II
I
II
!

11 I Englsih secuENTRY HOME 5000 CYL
Reading out the log le/history
An entry is automatically created in a
log le, the history, for every opening or
closing process. Follow the steps below
to read out the history.
Open the main menu (Fig. 79).
Tap on the menu item "secuENTRY
setup" (Fig. 80).
Tap on "History"
in the submenu (Fig. 81).
Note: To perform the following step,
you must be close to the cylinder for
which you want to read out the history.
Now tap on "Readout history". This
will retrieve the history data from the
cylinder (Fig. 82).
Next, you will be prompted to type in
your administrator code (I).
Tip: The entry is concealed. Tap the eye
symbol on the right side to visualise
and check the entry.
Below the entry eld is a large button
which is automatically titled with the
name of the respective cylinder. Tap it
to conrm (II) (Fig. 83).
The history data is now retrieved from
the cylinder and stored in the app as
alog le (Fig. 84).
1
2
3
4
5
7
6
Fig. 81
Fig. 83
Fig. 82
Fig. 84
Fig. 79 Fig. 80
!
!!
After retrieval, a conrmation message
appears, which you conrm with "OK"
(Fig. 85).
Go back one step in the menu and tap
on the item "Lock history" (Fig. 86).
A list of cylinders with retrieved log les
appears. Select the required cylinder
(Fig. 87).
The menu of the selected cylinder
shows the retrieved log le(s), sorted
by date and time. Tap the required le
(Fig. 88).
Note: The log les only show the
history up to the time of retrieval. Old
cylinder entries and log les can be
deleted by swiping the corresponding
entry to the left. A "Delete" button then
appears on the right-hand side.
The lock history is now displayed
(Fig. 89).
The following data is logged for the
ENTRY Home 5000 CYL:
I: User
II : Access medium
III : Opening/closing the cylinder
IV : Battery status
Administrator 00.00.2000 00:00 Code entry
00.00.2000 00:00 Door opened Bat. 4/4 Full
8
9
11
12
10
Fig. 87
Fig. 89
Fig. 88
Fig. 85 Fig. 86
I
II
I II
III VI

12 I Englsih secuENTRY HOME 5000 CYL
From inside the door, push the cylinder
into the mortise lock (Fig. 93).
Screw the cylinder into the door and
push the inside and outside knobs up
to the door
(Fig. 94).
Screw the hexagonal screws back into
the two knobs (Fig. 95).
ATTENTION: Ensure that the knob is
at least one millimetre away from the
door.
Remove the battery protection strip
from the battery compartment on the
inside knob (Fig. 96).
min. 1mm
2 mm
min. 1mm
5
6
7
4
!
secuENTRY 5000 CYL installation
The installation of the secuENTRY
5000 CYL is explained below. Prior to
installation, please read the installation
instructions carefully.
Remove the existing door lock cylinder
by loosening the forend screw in the
door and pulling out the cylinder with
the key inserted (Fig. 90).
Remove the two hexagonal screws
in the two knobs with the enclosed
hexagonal spanner (Fig. 91).
Pull o the knob on the outside
completely and pull the knob on the
inside as far back as possible (Fig. 92).
Tip: The knob on the inside is larger
than the knob on the outside.
Attention: The knob on the inside
cannot be pulled o. Do not try to
loosen it by force.
2 mm 4x
1.
2.
!
OUTDOOR INDOOR
3
2
1
!
!
Fig. 90
Fig. 91
Fig. 92
Fig. 93
Fig. 94
Fig. 95
Fig. 96

13 I Englsih secuENTRY HOME 5000 CYL
Battery status display and replacing the batteries
The battery status is shown on the dis-
play each time a secuENTRY cylinder is
activated via the KeyApp (Fig. 97). When
the batteries in the cylinder are running
low, replace them as soon as possible.
Attention: The batteries are located
in the cylinder knob on the inside of
the door. Please note that if you ignore
the battery status and the battery is
completely discharged, you will no
longer be able to open the lock from
the outside.
Instructions on replacing the batteries
are given below:
On the inside of the door at the front
end of the knob, remove the screw
with the TX8 screwdriver provided and
remove the front cover (Fig. 98).
Remove the old batteries and dispose
of them appropriately (Fig. 99).
Tip: Instructions for proper disposal can
be found on page 14 of this manual.
Insert two new batteries.
Make sure that the polarity is correct
according to the drawing (Fig. 99).
Replace the front cover and screw it on
tightly (Fig. 100).
Fig. 97
Fig. 101
Fig. 102
!
!
2
3
4
1
Fig. 98
Fig. 99
Fig. 100
Whether for one front door, several doors or a complete locking system: Simply congure your
individual unit with the secuENTRY modular system .
Your ENTRY HOME 5000 CYL cylinder can be extended with the following components:
secuENTRY
ENTRY 7711 Keypad PIN
Using the ENTRY 7711 Keypad PIN, you
can unlock and lock the door with a
6-digit user code. The transmission is
wireless via Bluetooth and is 128-bit
AES encrypted.
secuENTRY
ENTRY sE-Key 7713
The cylinder is opened simply by
pressing a button using the ENTRY
sE-Key 7713 radio key. The transmis-
sion is encrypted at a high security
level (AES encryption).
Compatibility with other secuENTRY products
Article number:
4003482507117
Further info available
on our website:
www.burg.biz
Article number:
4003482507131
Further info available
on our website:
www.burg.biz

14 I Englsih secuENTRY HOME 5000 CYL
In order to deliver a awless and high quality product to you and to better assist you in case of
service or repair, it is necessary that faulty or defective devices along with the valid administrator
code and the QR code(s) be presented to your dealer together with the original documentation.
When returning goods due to your right of withdrawal, all parts of the appliance must also be in
their factory settings. Failure to comply with this will invalidate the warranty.
Dear customer,
Please help to reduce waste. Should you intend to dispose of this device at any time, please
remember that many components of this device contain valuable materials that can be recycled.
Printing and typesetting errors as well as technical changes reserved.
Please note that electrical and electronic devices as well as batteries must not be
disposed of with household waste but rather apart from it or separately. Please obtain
information on the collecting points for electrical waste from the responsible authority
of your city/municipality.
BURG-WÄCHTER KG hereby declares that this device complies with Directives 2014/53/
EU, (RED) 2014/30/EU, (EMC) and 2011/65/EU (RoHs) .
The complete text of the EU Declaration of Conformity is available at the following
Internet address: www.burg.biz
Warranty Notes
Disposal of the device

www.burg.biz
BURG-WÄCHTER KG
Altenhofer Weg 15
58300 Wetter
Germany
www.burg.biz
ENTRY HOME
ENTRY 5000 CYL
BD Main Instruction Manual ENTRY 5000 CYL EN HBG/SWI 040422