Burkert 8745 MFM Ethernet User manual

Operating Instructions
Bedienungsanleitung
Manuel d‘utilisation
Type 8745
Industrial Ethernet
Analogue
Mass Flow Meter (MFM) / Mass Flow Controller (MFC)
Massendurchflussmesser (MFM) / Massendurchflussregler (MFC)
Débitmètre massique (MFM) / Régulateur de débit massique (MFC)

We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© Bürkert SAS, 2017 - 2021
Operating Instructions 2103/01_EU-ML_00569558 / Original EN

3
Table of contents
Type 8745 Ethernet, 8745 Analogue
1 THE OPERATING INSTRUCTIONS ............................................. 7
1.1 Denitionofthetermproduct .................................... 7
1.2 DenitionofthetermIndustrialEthernet.................... 7
1.3 About NAMUR and the NAMUR Recommen-
dationNE107............................................................. 7
1.4 Symbols used............................................................. 7
2 INTENDED USE .................................................................... 8
3 BASIC SAFETY INFORMATION............................................ 9
4 GENERAL INFORMATION .................................................. 10
4.1 Contact..................................................................... 10
4.2 Warranty ................................................................... 10
4.3 InformationontheInternet....................................... 10
5 DESCRIPTION..................................................................... 11
5.1 Product variants ....................................................... 11
5.1.1 MFMEthernet ................................................ 11
5.1.2 MFM Analogue............................................... 12
5.1.3 MFCEthernetwithproportionalvalve............ 13
5.1.4 MFCAnaloguewithproportionalvalve.......... 14
5.1.5 MFCEthernetwithmotorvalve...................... 15
5.1.6 MFC Analogue with motor valve.................... 16
5.2 Product status indicator ........................................... 16
5.3 MotorvalvestatusLED ............................................ 18
5.4 StatusLEDsspecictoaproductvariantEthernet...... 18
5.4.1 StatusLEDsfortheconnectiontothe
Ethernetnetwork................................................. 18
5.4.2 StatusLEDfortheeldbuscommuni-
cation(productvariantEthernet) ........................ 19
5.5 Memory card ............................................................ 19
5.6 büS-interface .....................................................................19
5.7 Control valve of an MFC........................................... 19
6 TECHNICAL DATA............................................................... 20
6.1 Conformity................................................................ 20
6.2 Standards................................................................. 20
6.3 Operatingconditions................................................ 20
6.3.1 MFM Analogue............................................... 21
6.3.2 MFMEthernet ................................................ 21
6.3.3 MFCAnaloguewithproportionalvalve.......... 22
6.3.4 MFCEthernetwithproportionalvalve............ 22
6.3.5 MFC Analogue with motor valve.................... 23
6.3.6 MFCEthernetwithmotorvalve...................... 23
6.4 Markings................................................................... 24
6.4.1 Calibrationplate ............................................. 24
6.4.2 Typelabel ....................................................... 24
6.4.3 Conformitymarking,certicationmarking..... 25
6.4.4 Markingsspecictoaproduct
variantEthernet.............................................. 25
6.5 Product materials ..................................................... 25
6.6 Dimensions,weight.................................................. 26
6.7 Fluid data ................................................................. 26
6.7.1 Mass Flow Meter............................................ 26
6.7.2 MassFlowControllerwithproportionalvalve 27
6.7.3 Mass Flow Controller with motor valve.......... 27
6.7.4 Qualityoftheoperatinguid.......................... 28
English

4
Type 8745 Ethernet, 8745 Analogue
6.8 Pressure loss (MFM)................................................. 28
6.8.1 Operatinggasisair ........................................ 28
6.8.2 Operatinggasisnotair.................................. 30
6.9 Electricaldata .................................................................. 31
6.9.1 ProductvariantEthernet...................................... 31
6.9.2 Product variant Analogue ................................... 31
6.10 Communicationinterface(productvariantEthernet) 33
7 FLUID INSTALLATION......................................................... 34
7.1 Safety instructions.................................................... 34
7.2 Installationsteps ...................................................... 35
7.3 Product variant with G-internal-threaded con-
nections.................................................................... 35
7.4 Product variant with NPT-internal-threaded
connections.............................................................. 38
7.5 Productvariantwithangeconnections.................. 39
8 ELECTRICAL INSTALLATION ............................................. 39
8.1 Safety instructions.................................................... 39
8.2 Additional documentation ........................................ 40
8.2.1 Product variant Analogue............................... 40
8.2.2 ProductvariantEthernet ............................... 40
8.3 WiretheproductvariantEthernet ............................ 40
8.4 Changethenetworkparameters.............................. 41
8.4.1 Overtheproductweb-server......................... 42
8.4.2 OvertheBürkertCommunicatorsoftware ..... 42
8.5 WireaproductvariantAnaloguewithD-sub
DE-9maleconnector ............................................... 43
8.5.1 Digitalinput .................................................... 44
8.5.2 Relayoutput................................................... 45
8.6 WireaproductvariantAnaloguewith6ter-
minal connections .................................................... 46
8.7 Connecting the functional earth............................... 47
9 COMMISSIONING............................................................... 47
9.1 Safety instructions.................................................... 47
9.2 Commissioningsteps............................................... 47
10 SETTING AND OPERATION ............................................... 48
10.1 Safetyinstructions.................................................... 48
10.2 Functions.................................................................. 49
10.2.1 Zero-pointshut-o(MFC) .............................. 49
10.2.2 Flushmode(MFCEthernet) ........................... 49
10.3 Toolsfordoingsettings............................................ 49
10.3.1 ProductvariantAnalogue.............................. 49
10.3.2 ProductvariantEthernet .............................. 50
10.4 ConnecttheproducttotheBürkertCommuni-
cator software .......................................................... 50
10.5 User-denedadjustment.......................................... 51
10.6 OperatingmodesofanMFC.................................... 51
10.7 Normaloperatingmode(MFC)................................. 52
10.7.1 ProductvariantEthernet ................................ 52
10.7.2 ProductvariantAnalogue............................... 52
10.8 Optimisetheclosed-loopcontrolparameters(MFC).... 53
10.9 Choosethesourcegivingtheset-pointvalue(MFC)54
10.10 Set-pointvalueswithoutcommunication(MFC
Ethernet) ................................................................... 54
English

5
Type 8745 Ethernet, 8745 Analogue
11 MAINTENANCE................................................................... 55
11.1 Maintenanceforoperationwithheavilycon-
taminateduids........................................................ 55
11.1.1 Inspectandcleanthestainlesssteel
mesh-lter ...................................................... 56
11.2 Cleaning and recalibration at the factory ................. 57
11.3 Replacethememorycard........................................ 57
12 TROUBLESHOOTING ......................................................... 58
12.1 Problemsshownbytheproductstatusindicator .... 58
12.1.1 Product status indicator is red (MFM
Analogue) ....................................................... 58
12.1.2 Product status indicator is red (MFM
Ethernet)......................................................... 59
12.1.3 Product status indicator is red (MFC
Analogue) ....................................................... 59
12.1.4 Product status indicator is red (MFC
Ethernet)......................................................... 59
12.1.5 Product status indicator is orange
(MFM Analogue)............................................. 60
12.1.6 Product status indicator is orange
(MFMEthernet)............................................... 60
12.1.7 Product status indicator is orange
(MFC Analogue) ............................................. 60
12.1.8 Product status indicator is orange
(MFCEthernet) ............................................... 60
12.1.9 Product status indicator is yellow
(MFM Analogue)............................................. 60
12.1.10 Productstatusindicatorisyellow
(MFMEthernet)............................................... 61
12.1.11 Product status indicator is yellow
(MFC Analogue) ............................................. 61
12.1.12 Product status indicator is yellow
(MFCEthernet) ............................................... 61
12.1.13 Product status indicator is blue ..................... 62
12.2 ProblemsshownbythestatusLEDofthe
motor valve............................................................... 62
12.2.1 LEDisredandashes,LEDisredandON ... 62
12.2.2 LEDisyellowandashes .............................. 62
12.3 Miscellaneousproblems .......................................... 62
12.3.1 Productstatusindicatoriso ....................... 62
12.3.2 Productstatusindicatorashes .................... 62
12.3.3 Product status indicator goes out
periodically..................................................... 62
12.3.4 Replacementproductadoptsnone
ofthevaluesfromthedefectiveproduct ....... 63
12.3.5 Replacementproductdoesnot
adoptallofthevaluesfromthe
defectiveproduct ........................................... 63
12.3.6 Nomassowrate(MFM) ............................... 63
12.3.7 Nomassowrate(MFC)................................ 63
12.3.8 Unstable measured value (MFM) ................... 64
12.3.9 Unstable measured value (MFC).................... 64
12.3.10 Set-pointvalueat0%,butoperating
uidstillows(MFC)...................................... 64
12.3.11 Set-pointvalueat0%,control
valveisclosed,nomassow,buta
non-zeromassowrateismeasured(MFC) . 64
12.3.12 Set-pointvalueisnotreached(MFC) ............ 65
English

6
Type 8745 Ethernet, 8745 Analogue
13 ACCESSORIES, SPARE PARTS ......................................... 65
13.1 Electricalaccessories............................................... 65
13.2 CompressionttingsforaproductwithG-in-
ternal-threaded connections .................................... 66
13.3 Meshlters............................................................... 66
13.4 Additional documentation and software .................. 66
14 DECOMMISSIONING.......................................................... 67
14.1 Safety instructions.................................................... 67
14.2 Dismantlingtheproduct........................................... 67
15 TRANSPORT....................................................................... 68
16 STORAGE, DISPOSAL ........................................................ 68
17 RETURNING THE PRODUCT ............................................. 68
English

7
The Operating instructions
Type 8745 Ethernet, 8745 Analogue
1 THE OPERATING INSTRUCTIONS
The Operating Instructions describe the entire life cycle of the
product.PleasekeeptheOperatingInstructionsinasafeplace,
accessible to all users and any new owners.
Important safety information.
▶ReadtheOperatingInstructions.Ifyoudonotunderstandthe
contentoftheOperatingInstructions,contactBürkert.
▶Payparticularattentiontothechpt.Basic safety information
andtothechpt.Intendeduse.
1.1 Denition of the term product
Theterm"product"asusedintheOperatingInstructionsrefers
to one or several of the following devices:
•aMassFlowMeter(MFM)Type8745Ethernet
•aMassFlowMeter(MFM)Type8745Analogue
•aMassFlowController(MFC)Type8745Ethernet
•aMassFlowController(MFC)Type8745Analogue
1.2 Denition of the term Industrial
Ethernet
Theterm"IndustrialEthernet"asusedintheOperatingInstruc-
tions,referstodevicesthatcommunicatewiththeeldbuspro-
tocolsPROFINET,EtherNet/IP,EtherCATorModbusTCP.
1.3 About NAMUR and the NAMUR
Recommendation NE107
Standards committee for measurement and control technology
(NAMUR) is an international association of users of automation
systemsfortheprocessindustry.
NAMURrecommendation(NE)107:self-monitoringanddiag-
nosisofelddevices.
1.4 Symbols used
DANGER
Warns of an immediate danger.
▶Failure to observe the warning results in death or in serious
injuries.
WARNING
Warnsofapotentiallydangeroussituation.
▶Failure to observe the warning can result in serious injuries or
in death.
CAUTION
Warns of a possible danger.
▶Failure to observe the warning can result in moderate or minor
injuries.
English

8
Intended use
Type 8745 Ethernet, 8745 Analogue
NOTICE
Warns of damage to property.
▶Failure to observe the warning may result in damage to the
product or system.
Indicatesimportantadditionalinformation,tipsand
recommendations.
ReferstoinformationintheOperatingInstructions,orin
other documents.
▶Designatesaninstructionforriskprevention.
→Designatesaworkstepthatyoumustcarryout.
Indicatesaresult.
Menu Designates a text of a user interface.
2 INTENDED USE
Improper use of the product may be a hazard to people, nearby
equipment and the environment.
MFM Type 8745 Ethernet or MFM Type 8745 Analogue is used
exclusively to measure the mass ow rate of clean and dry
gases.
MFC Type 8745 Ethernet or MFC Type 8745 Analogue is used to
measure and regulate the mass ow rate of clean and dry gases.
▶Observethedatathatisgiveninthecontractdocuments,the
OperatingInstructions,ontheTypelabelandonthecalibration
plate:
-additional data
-operatingconditions
-service conditions
▶Onlyusetheproductfortheuidsthatareindicatedonthe
Typelabelandinthecalibrationprotocol.
▶Onlyusetheproductindoors.
▶Onlyusetheproductuptoanaltitudeof2000m.
▶Onlyusetheproductwithexternalinstrumentsthattheproduct
manufacturer recommends.
▶Onlyusetheproductwithcomponentsthattheproductman-
ufacturer recommends.
▶Operatetheproductcarefullyandensureregularandprofes-
sional maintenance.
▶Operatetheproductonlyinperfectworkingorder.Ensure
appropriatestorage,transport,installationanduse.
▶Onlyusetheproductforitsintendedpurpose.
English

9
Basic safety information
Type 8745 Ethernet, 8745 Analogue
3 BASIC SAFETY INFORMATION
Thissafetyinformationdoesnottakeintoaccountanycontin-
genciesoroccurrencesthatmayariseduringinstallation,use
andmaintenanceoftheproduct.
Theoperatingcompanyisresponsiblefortherespectofthelocal
safetyregulationsincludingforthepersonnelsafety.
Risk of injury that is due to pressure in the installation or in
the product.
▶Beforeworkingontheinstallationorproduct,cutthepres-
sure.Ventanddrainthepipes.
Risk of injury from electric shocks.
▶Beforeworkingontheinstallationorproduct,switchothe
powersupply.Makesurethatnobodycanswitchthepower
supplyon.
▶Observeallapplicableaccidentprotectionandallapplicable
safetyregulationsforelectricalequipment.
Burn hazard and re hazard that are due to hot surface of the
product.
▶Do not touch the hot surface with bare hands.
▶Wearsafetyglovestotouchtheproduct.
▶Keeptheproductawayfromanyhighlyammablematerials
oruids.
Risk of injury that is due to escape of the uid.
▶Observeallapplicableaccidentprotectionandallapplicable
safetyregulationsrelatingtotheoperatinguidused.
Various dangerous situations.
Toavoidpersonalinjury,obeythefollowinginstructions:
▶Donotoperatetheproductwithoutitsmeshlter.
▶Onlyoperatetheproductintheinstallationpositiongivenon
thecalibrationplate.
▶MakesurethattheoperatingpressureoftheMFMisnot
higherthanthemaximumcalibrationpressurethatisgiven
onthecalibrationplate.
▶MakesurethattheoperatingpressureoftheMFCisnot
higherthanthetightsealingpressureofthecontrolvalve.
▶Onlyusetheproductfortheuidspeciedastheoperating
uidinthecalibrationprotocol.
▶Onlyuseagentsthatarestablewiththeproductmaterialsfor
cleaning and decontamination
Findthecompatibilitychartonourhomepage:
country.burkert.com
Intheeventofanyambiguitypleasecontactyourlocalsales
oce.
▶Donotmakeanymodicationstotheproductanddonot
subjecttheproducttomechanicalstress.
▶Protecttheinstallationandtheproductfromaccidental
actuation.
▶Onlytrainedpersonnelmayperforminstallationworkand
maintenancework.
▶Afteraninterruptionintheelectricalsupplyorintheuid
supply,ensureacontrolledrestartoftheprocess.
▶Observebestindustrypractice.
English

10
General information
Type 8745 Ethernet, 8745 Analogue
NOTICE
Components or assemblies at risk from electrostatic
charges.
Theproductcontainselectroniccomponentswhicharesuscep-
tibletoelectrostaticdischarge(ESD).Contactwithelectrostati-
callychargedpersonsorobjectsendangersthesecomponents.
Intheworstcase,theywillbecomedefectiveimmediatelyorwill
fail when energised.
•To minimise or even avoid any damage caused by an elec-
trostaticdischarge,takealltheprecautionsdescribedinthe
EN61340-5-1.
•Donottouchanyoftheliveelectricalcomponents.
4 GENERAL INFORMATION
4.1 Contact
Thenameofthemanufacturerisdisplayedasinsetwritingonthe
coverandthehousingoftheproduct.
Tocontactthemanufactureroftheproduct,usethefollowing
address:
BürkertSAS
Rue du Giessen
F-67220TRIEMBACH-AUVAL
Theaddressesofourinternationalsalesocesareavailableon
the internet at: country.burkert.com
4.2 Warranty
Thewarrantyisconditionaloncompliantuseoftheproductin
observanceoftheoperatingconditionsspeciedintheOper-
atingInstructions.
4.3 Information on the Internet
OperatingInstructionsanddatasheetsfortheproductcanbefound
online at: country.burkert.com
English

11
Description
Type 8745 Ethernet, 8745 Analogue
5 DESCRIPTION
5.1 Product variants
5.1.1 MFM Ethernet
6
7
10 9
8
1
3
4
2
5
1. Electricalconnections:
-3 removable terminal connections that are delivered with
theproduct
-2xRJ45ports
2. StatusLEDsfortheconnectiontotheEthernetnetwork
3. Possibleuidconnections:
-G-internal-threaded connections according to
DINISO228/1
-NPT-internal-threadedconnectionsaccordingtoASME/
ANSIB1.20.1
-angeconnection
4. M4 screw for functional earth connection
5. Baseblock
6. Flow direction
7. Productstatusindicator.Theindicatoroperatesaccording
toNAMURNE107.
8. StatusLEDfortheeldbuscommunication
9. büSinterfacefortheBürkertCommunicatorsoftware
10.Slot for the memory card
Fig. 1: Product variants of an MFM Ethernet
English

12
Description
Type 8745 Ethernet, 8745 Analogue
5.1.2 MFM Analogue
5
6
87
2
3
1
4
1. Possible electrical connection:
-D-subDE-9maleconnector
-6 removable terminal connections that are delivered with
theproduct
2. Possibleuidconnections:
-G-internal-threaded connections according to
DINISO228/1
-NPT-internal-threadedconnectionsaccordingtoASME/
ANSIB1.20.1
-angeconnection
3. M4 screw for functional earth connection
4. Baseblock
5. Flow direction
6. Productstatusindicator.Theindicatoroperatesaccording
toNAMURNE107.
7. büSinterfacefortheBürkertCommunicatorsoftware
8. Slot for the memory card
Fig. 2: Product variants of an MFM Analogue
English

13
Description
Type 8745 Ethernet, 8745 Analogue
5.1.3 MFC Ethernet with proportional valve
7
8
11 10
9
1
3
4
2
56
1. Electricalconnections:
-3 removable terminal connections that are delivered with
theproduct
-2xRJ45ports
2. StatusLEDsfortheconnectiontotheEthernetnetwork
3. Possibleuidconnections:
-G-internal-threaded connections according to
DINISO228/1
-NPT-internal-threadedconnectionsaccordingtoASME/
ANSIB1.20.1
-angeconnection
4. M4 screw for functional earth connection
5. Baseblock
6. Flow direction
7. Proportionalvalve
8. Productstatusindicator.Theindicatoroperatesaccording
toNAMURNE107.
9. StatusLEDfortheeldbuscommunication
10.büSinterfacefortheBürkertCommunicatorsoftware
11. Slot for the memory card
Fig. 3: Product variants of an MFC Ethernet with proportional valve
English

14
Description
Type 8745 Ethernet, 8745 Analogue
5.1.4 MFC Analogue with proportional valve
5
7
98
2
3
1
4
6
1. Possible electrical connection:
-D-subDE-9maleconnector
-6 removable terminal connections that are delivered with
theproduct
2. Possibleuidconnections:
-G-internal-threaded connections according to
DINISO228/1
-NPT-internal-threadedconnectionsaccordingtoASME/
ANSIB1.20.1
-angeconnection
3. M4 screw for functional earth connection
4. Baseblock
5. Flow direction
6. Proportionalvalve
7. Productstatusindicator.Theindicatoroperatesaccording
toNAMURNE107.
8. büSinterfacefortheBürkertCommunicatorsoftware
9. Slot for the memory card
Fig. 4: Product variants of an MFC Analogue with proportional valve
English

15
Description
Type 8745 Ethernet, 8745 Analogue
5.1.5 MFC Ethernet with motor valve
9
7
12
11
10
1
5
8
3
4
2
6
1. Electricalconnections:
-3 removable terminal connections that are delivered with
theproduct
-2xRJ45ports
2. StatusLEDsfortheconnectiontotheEthernetnetwork
3. StatusLEDofthemotorvalve
4. Motor valve
5. Possibleuidconnections:
-G-internal-threaded connections according to
DINISO228/1
-NPT-internal-threadedconnectionsaccordingtoASME/
ANSIB1.20.1
-angeconnection
6. Baseblock
7. Productstatusindicator.Theindicatoroperatesaccording
toNAMURNE107.
8. M4 screw for functional earth connection
9. Flow direction
10.StatusLEDfortheeldbuscommunication
11. büSinterfacefortheBürkertCommunicatorsoftware
12. Slot for the memory card
Fig. 5: Product variants of an MFC Ethernet with motor valve
English

16
Description
Type 8745 Ethernet, 8745 Analogue
5.1.6 MFC Analogue with motor valve
8
6
1
4
7
2
3
5
10
9
1. Possible electrical connection:
-D-subDE-9maleconnector
-6 removable terminal connections that are delivered with
theproduct
2. StatusLEDofthemotorvalve
3. Motor valve
4. Possibleuidconnections:
-G-internal-threaded connections according to
DINISO228/1
-NPT-internal-threadedconnectionsaccordingtoASME/
ANSIB1.20.1
-angeconnection
5. Baseblock
6. Productstatusindicator.Theindicatoroperatesaccording
toNAMURNE107.
7. M4 screw for functional earth connection
8. Flow direction
9. büSinterfacefortheBürkertCommunicatorsoftware
10.Slot for the memory card
Fig. 6: Product variants of an MFC Analogue with motor valve
5.2 Product status indicator
Theproductstatusindicatorchangesitscolourbasedonthe
NAMURrecommendationNE107.Thecolouroftheproduct
statusindicatorgivesthefollowingpiecesofinformation:
•Whetherproductdiagnosticsareactiveornot.Diagnosticsare
activeontheproductandcannotbedeactivated.
•Ifproductdiagnosticsareactive,thentheproductstatusindi-
cator shows whether diagnostics events have been generated
ornot.Ifseveraldiagnosticseventshavebeengenerated,then
theproductstatusindicatorshowsthediagnosticseventwith
English

17
Description
Type 8745 Ethernet, 8745 Analogue
thehighestpriority.Referto Tab. 1.
Iftheproductstatusindicatorashes,thentheproductisselectedinaman-machineinterfacesuchastheBürkertCommuni-
cator software.
Tab. 1: Product status indicator in accordance with NAMUR NE107, edition 2006-06-12, for active diagnostics
Colour
according to
NE107
Colour code
(for a PLC)
Diagnostics event
according to NE107
Meaning
Red 5 Failure,errororfault MFM:Duetoamalfunctionoftheproductoritsperiphery,themeasuredvaluesarenot
valid.
MFC:Duetoamalfunctionoftheproductoritsperiphery,themeasuredvaluesarenot
validandtheproductcannotregulateanymore.
Orange 4 Checkfunction Theproductisbeingworkedon.
•MFM:Theoutputsignalistemporarilyinvalid.
•MFC:Theproductcannotregulatetemporarily.
Yellow 3 Outofspecication Theambientconditionsorprocessconditionsfortheproductareoutsidethespecied
ranges.
Productinternaldiagnosticspointtoproblemsintheproductorwiththeprocess
properties.
Blue 2 Maintenance required →Dotherequiredmaintenanceoperation.
MFM:Theproductcontinuestomeasure.
MFC:Theproductcontinuestoregulate,butafunctionistemporarilyrestricted.
Green 1 - Diagnostics are active and no diagnostics event has been generated.
TheMFCproductvariantoperatesinthenormaloperatingmodeorinStored set-point
valueoperatingmode.Refertochpt.10.7Normaloperatingmode(MFC)andchpt.10.9
Choosethesourcegivingtheset-pointvalue(MFC).
→Tosolveaproblemthatisindicatedbytheproductstatusindicator,refertochpt.12.1.
English

18
Description
Type 8745 Ethernet, 8745 Analogue
5.3 Motor valve status LED
ThecolourandstatusofthemotorvalvestatusLEDgivethefol-
lowingpiecesofinformation:
•Whetherthemotorvalvefacesaproblemornot.
•Whetherthemotorvalveiscompletelyopenorclosed.
Tab. 2: Status of the motor valve depending on the colour of the status
LED
Colour of
the LED
Status of the LED Status of the motor valve
-LEDout Motor valve is not energised
white LEDlit Motorvalveoperatesnormally
yellow LEDlit Motorvalveiscompletelyopen
LEDashing.The
colour alternates
with the colour
that indicates the
positionofthe
motor valve.
The ambient conditions or the
processconditionsforthemotor
valveareoutsidethespecied
ranges. The ambient conditions
ortheprocessconditionsforthe
motorvalveareoutsidethespec-
iedranges.
green LEDlit Motor valve is closed
red LEDashing.The
colour alternates
with the colour
that indicates the
positionofthe
motor valve.
Error
5.4 Status LEDs specic to a product
variant Ethernet
5.4.1 Status LEDs for the connection to the
Ethernet network
EachRJ45portofaproductvariantEthernetvarianthas2LEDs
toshowthestatusoftheconnectiontothenetwork.
Link/ActLED(green) LinkLED(yellow)
Fig. 7: Location of the LEDs for the connection to the Ethernet network
Tab. 3: Description of the Link/Act LED
Link/Act LED Meaning
ON,fastashing Connectiontotheparentprotocollayerisestab-
lished. Data is being exchanged.
ON,slow
ashing
Noconnectiontotheprotocollayer.
Happensabout20secondsafterrestartofthe
product.
OFF Noconnectiontothenetwork.
Tab. 4: Description of the Link LED
Link LED Meaning
ON Connectiontothenetworkisestablished.
OFF Noconnectiontothenetwork.
English

19
Description
Type 8745 Ethernet, 8745 Analogue
5.4.2 Status LED for the eldbus
communication (product variant
Ethernet)
AproductvariantEthernethasanLEDtoshowthestatusofthe
communicationbetweentheproductandthePLC(Program-
mable Logical Controller).
Tab. 5: Description of the communication LED
Communication
LED
Description Meaning
Green RUN Cyclic data is being exchanged
betweentheproductandtheeldbus
master
Red ERROR No cyclic data is being exchanged
betweentheproductandtheeldbus
master
5.5 Memory card
NOTICE
Ifthememorycardisdefectiveorlost,buyanewmemorycard
atyourBürkertsalesoce.
Theproductis deliveredwith a memorycardthatisinsertedin
theproduct.
Whentheproductisenergised,therearetwopossibilities:
•Ifproduct-specicdataisstoredontheinsertedmemorycard,
theproductadoptsthedata.Atproductdelivery,thememory
cardcontainsproduct-specicdata.Togetalistofthestored
data,refertotheHelpfortheInitiationlethatcanbedown-
loaded from country.burkert.com.
•Iftheinsertedmemorycardisempty,theproductloadsits
owndataonthememorycard.Anewmemorycardisempty.
The data on the memory card can be transferred to another
productwiththesamearticlenumber.Forexample,thedatacan
betransferredfromadefectiveproducttoanewproduct.
5.6 büS-interface
ThebüS-interfaceisusedforshort-termservicingoftheproduct
withtheBürkertCommunicatorsoftware.
→ToconnecttheproducttotheBürkertCommunicator
software,refertochpt.10.4.
5.7 Control valve of an MFC
TheMFCisequippedwithoneofthefollowingcontrolvalvetypes:
•Adirectacting,normally-closedproportionalvalve.
•Amotor-drivenvalvethatiscalledmotorvalve.Ifde-energised,
themotorvalveremainsinitslatestposition.
Thecontrolvalveprovidesthesealingfunctionwhenthefol-
lowing conditions are met:
•Theproductisusedwithinthespeciedpressurerange.
•Theproductisequippedwithavalveseatsealthatismadeof
asoftmaterialsuchasFKMorEPDM.
English

20
Technical data
Type 8745 Ethernet, 8745 Analogue
NOTICE
If the valve seat seal is made of a hard material such as
PCTFE, then the control valve may not be tight.
Productswithanominalvalvediameterof0.05mmor0.1mm
have a valve seat seal made of a hard material.
6 TECHNICAL DATA
6.1 Conformity
TheproductcomplieswiththeEUdirectivesaccordingtotheEU
declarationofconformity(ifapplicable).
6.2 Standards
Theappliedstandards,whichverifyconformitywiththeEUdirec-
tives,canbefoundontheEUtypeexaminationcerticateand/or
theEUdeclarationofconformity(ifapplicable).
6.3 Operating conditions
WARNING
Risk of injury from malfunction due to outdoor use.
▶Donotusetheproductinoutdoorareas.
WARNING
Risk of injury caused by pressure, uid escape.
Importantproduct-specicdataisindicatedontheTypelabel
andcalibrationplate.
▶Onlyusetheproductforthespeciedoperatinguid.
▶Donotexceedthespeciedcalibrationpressure.
English