BWI Eagle AIR-EAGLE XLT Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE® XLT
900
MHz
RF
Trans
ceiver
MODEL 44
1
-
4
0
4
0
0
-
D
C
DESCRIPTION
The AIR-EAGLE XLT RF TRANSCEIVER IS a four I/O unit designed to
transmit and receive unique signals from one or more transceivers located
up to 2500 feet (or more) away. This model comes equipped with four
contact inputs and four 5amp SPDT relay outputs. This allows the user to
not only transmit information out but receive a confirming signal back that
the operation was performed. The Air-Eagle XLT TRX is user-
programmable for up seven network frequencies to allow multiple systems
to operate simultaneously in the same area and utilizes spread-spectrum
technology to provide the utmost security and reliability even in the
noisiest RF environments. A terminal strip has been provided for
interfacing with external dry contact inputs as well as dry contact relay
outputs. This unit can operate remote machinery such as pumps, gates,
chutes etc.
APPROVALS
United States (FCC) MCQ-XB900HP
Canada (IC) 1846A-XB900HP
INSTALLATION
DISCONNECT DC Power from all equipment before installation.
1. Mount the AIR-EAGLE XLT TRANSCEIVER in a convenient location.
2. Select relay options, repeater mode, channel codes and frequency if
desired (see page 2)
3. Install input & output wiring to the terminal strip
4. Install antenna to TNC connector on the right side of the enclosure.
5. Connect DC power to the proper terminals in your control circuit.
TERMINAL STRIP WIRING
INPUTS OUTPUTS
1 Common Input 1 9 N/O Relay #1 15 N/O Relay #3
2 Input 1 10 C Relay #1 16 C Relay #3
3 Common Input 2 11 N/C Relay #1 17 N/C Relay #3
4 Input 2 12 N/O Relay #2 18 N/O Relay #4
5 Common Input 3 13 C Relay #2 19 C Relay #4
6 Input 3 14 N/C Relay #2 20 N/C Relay #4
7 Common Input 4
8 Input 4
D
C INPUT
Terminal #1 (-) 9-36VDC Input
Terminal #2
(+) 9
-
36VDC Input
GENERAL OPERATION
Contact closures on inputs 1 thru 4 in the control transceiver transmit
to activate relay #1 thru #4 in the remote transceiver. Inputs from the
remote equipment provide closures to remote transceiver that transmit
to energize relays #1 thru #4 in the control transceiver.
INPUT
ACTIVATED
ACTION
"1" Transmits channel 1 command to remote unit
"2" Transmits channel 2 command to remote unit
"3" Transmits channel 3 command to remote unit
"4" Transmits channel 4 command to remote unit
INPUT CODE
RECEIVED
ACTION
"1" Relay #1 energizes, maintained momentary
"2" Relay #2 energizes, maintained momentary
"3" Relay #3 energizes, maintained momentary
"4" Relay #4 energizes, maintained momentary
All manuals and user guides at all-guides.com

AIR-EAGLE® XLT
900MHz
RF
Trans
ceiver
MODEL 4
4
1
-
40
4
0
0
-
D
C
RELAY, REPEATER MODE, CHANNEL
CODES & FREQUENCY SETTINGS
The unit is shipped from the factory with SEL1 switches in the open
positions. The relays will operate as maintained momentary, the unit is
transmitting & receiving channel 1 thru 4 commands, the command
transmitted will not be repeated, and it is operating on frequency 1.
If you wish to change these default settings, follow the instructions on the
table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired relay operation, repeater mode, channel codes
and/or network frequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
RELAY CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN CLOSED
SW1 Relay #1 momentary (default) Relay #1 toggle/latch
Relay #2 momentary (default) Relay #2 toggle/latch
SW2 Relay #3 momentary (default) Relay #3 toggle/latch
Relay #4 momentary (default) Relay #4 toggle/latch
Momentary – Relay mimics button or input – when depressed or
closed, relay will be energized; when released, relay de-energizes
Toggle Latch – Relay changes (and holds) its state each time the
corresponding button or input is
depressed or closed momentarily
CHANNEL CODE SET-UP
SEL1
SWITCH
NUMBER
OPEN CLOSED
SW3
Transmitting & Receiving
Channel Codes 1 thru 4
(default)
Transmitting &
Receiving Channel
Codes 5 thru 8
REPEATER MODE
SEL1
SWITCH
NUMBER
OPEN CLOSED
SW4 Repeater Mode OFF
(
d
efault)
Repeater Mode ON
FREQUENCY SET-UP
SEL1 Network
Frequency
SW5 SW6 SW7
(SW5-7)
1 (default) OPEN OPEN OPEN
2
CLOSED
OPEN
OPEN
3 OPEN CLOSED OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
DOCUMENT DATE: 03/17/2020 / PRODUCT REV. 2
SPECIFICATIONS
D
C Input
9
-
36
VDC @ 10 Watts
Fuse Protected
1 amp
Frequency
900MHz Spread Spectrum
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC per
channel
Transmitter Data
Four
Dry Contact Inputs
RF Output Power
25
0 mW
Transceiver Range
Approximately 2500 feet w/standard antenna
RF Channels
Seven
independent network frequencies
Enclosure
Hinged fiberglass with window / NEMA 3,
3R, 4,
1
2, 13
Operating Temp
-
40
o
F to +185
o
F
DIMENSIONS
REPLACEMENT PARTS & ACCESSORIES
Standard Antenna (Included):
900MHz Portable Antenna (For
distances up to
2500 Ft.)
49
-
1103
Optional Antennas and Accessories:
900MHz Omni Directional Antenna (For
distances up to
2
miles*)
49
-
3101
900MHz 13dB Yagi Antenna
Long Range Operation (For distances up
to
4
miles*)
49
-
3102
Flex Coax Cable w/Connectors
49-4000-XX
(XX = # of Feet)
* = Line of Sight
All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com