BWI Eagle AIR-EAGLE XLT 441AN-6000-4-20O-120VAC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Transceiver
MODEL 441AN-6000-4-20O-120VAC
DESCRIPTION
The AIR-EAGLE XLT, MODEL 441AN-6000-4-20-120VAC Is an RF
transceiver capable of transmitting two 4-20mA or 0-5VDC inputs and
receiving two 4-20mA analog signals. Two transceivers are used
together to create a long-range radio frequency system that monitors
electrical apparatus from safe, convenient locations of up to 2500 feet
away. (Or longer with optional antennas) This unit is user-
programmable for up to eight network frequencies to allow multiple
systems to operate simultaneously in the same area without
interference.
INSTALLATION
1. Mount the AIR-EAGLE XLT TRANSCEIVER in a convenient location
2. Install wiring to input/output terminal strip.
3. Designate a “master” unit and set SEL1 Switch #3 accordingly.
4. Install antenna onto TNC connector onside of unit.
5. Plug supplied AC wall plug adapterinto 110VAC outlet.
TERMINAL STRIP WIRING
1
2
3
4
5
6
7
8
9
10
Input 1 4-20mA (-)
Input 1 4-20mA (+)
Input 2 4-20mA (-)
Input 2 4-20mA (+)
Output 1 4-20mA (-)
Output 1 4-20mA(+)
Output 2 4-20mA(-)
Output 2 4-20mA(+)
(-) 12VDC input from included AC wall adapter
(+) 12VDC input from included AC wall adapter
CONTROLS & INDICATORS
OUTPUT
FAULT LEDS
Each Channel has a RED LED that will turn on
when thecurrent output is open
Similar Model Pictured
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
INPUT OPTIONS & FREQUENCY SET-UP
This transceiver is factory setfor4-20mA input, 4mAlink loss andto
operate on frequency #1. If you wish to changethe default settings, follow
the instructions using the table below:
1) Remove power from unit
2) Remove top cover.
3) Select desired input options and/or frequency usingtable below.
4) Reattach cover and apply power.
5) Programming is now complete.
INPUT CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW1
4-20mA Input (default)
0-5VDC Input
SW2
Link Loss 4mA (default)
Link Loss 20mA
SW3
Slave (default)
Master
Note –A dedicated master unit MUST be selected.
SW4
Reserved for future use
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED

AIR-EAGLE®XLT
900 MHz RF Transceiver
MODEL 441AN-6000-4-20O-120VAC
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
Australia
RCM
Brazil
ANATEL 3727-12-1209
SPECIFICATIONS
Inputs
Two 4-20mA (or) 0-5VDC
Outputs
Two 4-20mA
Safety Timer
15 seconds
Update Time
4 samples / second
AC Input
100-240 VAC, 16 W, 50/60 Hz from
supplied wall adapter
Enclosure
Polycarbonate NEMA 4 (IP66)
Frequency
900MHz Spread Spectrum
8 Independent Networks
RF Output Power
250 mW
Transmit Range
Up to 2500 Feet w/standard antenna
Note: Max range figures are estimates, based on free-air terrain with limited sources of
interference. Actual range will vary based on transmitting power, orientation of
transmitter and receiver, height of transmitting antenna, height of receiving antenna,
weather conditions, interference sources in the area, and terrain between receiver and
transmitter, including, but not limited to, indoor and outdoor structures such as walls,
metal objects, trees, buildings, hills, and mountains.
Operating Temperature
-40oF to +185oF
ACCESSORIES
Standard Antenna (Included):
900MHz TNC “Rubber Duck” Antenna
49-1103
Mobile/Base Antennas –
Used to help achieve max range in both non line of sight and line
of sight applications. - Contact BWI Eagle for recommendations
900MHz Thru-Hole Mount Mobile Antenna
49-2101
900MHz Magnet Mount Mobile Antenna
49-2102
900MHz Omni Directional Base Antenna
49-3101
900MHz Yagi Directional Base Antenna
49-3102
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available
in 5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of Feet)
Bulkhead Extensions –
Used to provide an external antenna connection whenmounting
control unit inside another enclosure
TNC Male to TNCBulkhead CableAssembly
- Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
(X = # of Feet)
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants theAir-Eagle Remote Control System, if properly
used and installed, will be free from defects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to includethe
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitnessfor
a particular purpose. BWI Eaglemakes no express warranties beyond
thosestatedhere. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss duringshipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 03/11/2022 / PRODUCT REV. 2
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com

4-20mA Installation
The above diagram shows a 4-20mA sensor hooked to channel 1 input. The 250 Ohm input resistor will
drop a voltage of 1 Volt at 4mA and 5 Volts at 20mA. The sensor may be of any type and voltage that
has a 4-20mA output. Even if the sensor runs on a voltage higher than 5 volts the current is still
maintained between 4 and 20 milliamps so that the voltage drop on the resistor is always between 1 and
5 volts. Remaining voltage is dropped internally in the sensor. Loop powered sensors are not able to be
used on this particular unit.
The above diagram shows the channel 1 output hooked to a 4-20mA receiver or PLC. The input
resistance of the receiver can be up to 500 ohms. Anything higher and the current will be limited to
below 20 mA since the maximum output voltage of the channel outputs is 10 volts.