BWI Eagle AIR-EAGLE SR PLUS Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR PLUS
2.4 GHz RF Transceiver
MODEL 36-6000-DC
DESCRIPTION
The AIR-EAGLE SRPLUSRF TRANSCEIVER IS a dual I/O unitdesigned to
transmit and receive unique signals from another transceiver located upto
600 feet away. This modelcomes equipped with three contact inputs and
two high current SPDT relay outputs. This allows the user to not only
transmit information out but receive a confirming signal back that the
operation was performed. The Air-Eagle SR PLUS TRX is user-
programmable for up to eight network frequencies to allow multiple
systems to operate simultaneously in the same area and utilizes spread-
spectrum technology and provides the utmost security andreliabilityeven
in the noisiest RF environments.
INSTALLATION
DISCONNECT Power from all equipment before installation.
1. Mount the control unit in a convenient location.
2. Install control wiring to terminalstrip.
3. Make desired relay,channel code and frequency selections using
instructions on page 2.
4. Attach antenna to TNCconnector located on the right side on the
enclosure.
5. Connect DC power tothe proper terminals in your control circuit.
PC BOARD SET-UP INFORMATION
Make the following connections on the PC Board Terminal Strip (TER1)
TERMINAL STRIP WIRING (TER1)
Terminal 1
Negative (-) 9-36VDC INPUT
Terminal 2
Positive (+) 9-36VDC INPUT
Terminal 3
CH1 Dry Contact Input (Common)
Terminal 4
CH1 Dry Contact Input
Terminal 5
CH2 Dry Contact Input (Common)
Terminal 6
CH2 Dry Contact Input
Terminal 7
CH3 Dry Contact Input (Common)
Terminal 8
CH3 Dry Contact Input
Terminal 9
CH1 Relay N/O
Terminal 10
CH1 Relay C
Terminal 11
CH1 Relay N/C
Terminal 12
CH2 Relay N/O
Terminal 13
CH2 Relay C
Terminal 14
CH2 Relay N/C
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS & INDICATORS
POWER/TX LED
Illuminates Green when power is applied,
changes to Red when transmitting.
LED1
Green LED illuminates continuously while relay
#1 is energized
LED2
Green LED illuminates continuously while relay
#2 is energized
CH1 –CH3 Dry
Contact Inputs
Transmit individual RF codes to the remote
transceiver
REL1 & REL2
Two SPDT output control relays
RF1
RF Module that transmits/receives data for
corresponding unit

AIR-EAGLE®SR PLUS
2.4 GHz RF Transceiver
MODEL 36-6000-DC
RELAY, CHANNEL CODES & FREQUENCY
SETTINGS
The unit is shipped from the factory with SEL1 switches in the open
positions. The relays will operate asmaintained momentary,the unit is
transmitting & receiving channel 1 & 2 commands and it is operating on
frequency 1. If you wish to change these default settings, follow the
instructions on the table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired relay operation, channel codes to be sent & received
and network frequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
RELAY CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW1
Relay #1 momentary (default)
Relay #1 toggle/latch
SW2
Relay #2 momentary (default)
Relay #2 toggle/latch
Maintained Momentary –Relay mimics button or input –when
depressed or closed, relay will be energized; when released, relay de-
energizes
Toggle Latch –Relay changes (and holds) its state each time the
corresponding button or input is depressed or closed.
CHANNEL CODE SET-UP
SEL1
(SW3-4)
Channel Codes To
Be Transmitted &
Received
SW3
SW4
1 & 2 (default)
OPEN
OPEN
3 & 4
CLOSED
OPEN
5 & 6
OPEN
CLOSED
7 & 8
CLOSED
CLOSED
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
DIMENSIONS
APPROVALS
United States (FCC)
OUR-XBEEPRO
Canada (IC)
4214A-XBEEPRO
Europe (CE)
ETSI
SPECIFICATIONS
DC Input
9 –36 VDC @ 10Watts
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC
Fuse Protected
1 amp
Transceiver Frequency
2.4 GHz Spread Spectrum
RF Output Power
60 mW
Transceiver Range
Approximately 600 feet
Transceiver Channels
8 Independent Network Frequencies
Antenna Connection
TNC Bulkhead
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
Weight
Approx 2 lbs.

AIR-EAGLE®SR PLUS
2.4 GHz RF Transceiver
MODEL 36-6000-DC
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
36-6002-DC
Standard Antenna (Included):
2.4GHz TNC Portable Antenna
49-1201
Optional Antennas and Accessories –
Used to increase range in both non line of sight and line of sight
applications. - Contact BWI Eagle for recommendations
2.4GHz Thru-Hole Mount Mobile Antenna
49-2201
2.4GHz Magnetic Mount Mobile Antenna
49-2202
2.4GHz Omni Directional Antenna
49-3201
2.4GHz 13dB Yagi Antenna
49-3202
Flex Coax Cable w/Connectors –Connects
external antenna(s) to base unit(s).
49-4000-XX
(XX = # of Feet)
2 Ft. Bulkhead Assembly (Used when
mounting receiver inside another enclosure)
49-5004-2-ISO
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly
used and installed, will be free fromdefects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to includethe
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair, improperinstallation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply onlyto the original purchaser of the equipment, and
last only for as long as such purchasercontinues to own the equipment.
This warranty replaces all other warranties, express orimplied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eaglemakes no express warranties beyond
those stated here. BWI disclaims without limitation, impliedwarranties of
merchantability and fitness for a particular purpose.Some jurisdictionsdo
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss during shipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 06/28/2019 / PRODUCT REV. 6
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com