BWI Eagle AIR-EAGLE XLT PLUS 461-40800-DC User manual

AIR-EAGLE XLT PLUS
461-40800-DC
900 MHz RF Transceiver
Document Date: 8/5/2022
Product Rev: 4

461-40800-DC
1
WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free
from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to
include the repair or replacement of defective equipment. This warranty does not cover damage due to
external causes, including accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited
warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of
the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty
replaces all other warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a
particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation
may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.
When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during
shipping and is responsible for the shipping costs incurred.
SIGNAL RANGE
Max range statements are estimates based on a clear line of sight with few interferences. Actual range will
vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and
receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including
but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).
WIRELESS STOP SYSTEMS WORK IN CONJUCTION WITH
HARD-WIRED SYSTEMS.
Wireless Stop and E-Stop devices must work in conjunction with a hard-wired
system. A wireless system should never be considered a primary life-saving device.
At least one hard-wired switch must be available in the event the wireless signal is
lost. Failure to comply may result in serious injury or death to personnel and
damage to equipment.

461-40800-DC
2
INTRODUCTION
The AIR-EAGLE XLT PLUS RF TRANSCEIVER provides two-way wireless control of electronic equipment and
apparatus at distances up to 1 mile away (longer ranges can be achieved with external antennas). This
model comes equipped with eight dry contact inputs and eight relay outputs. This allows the user to not
only transmit information out but receive a confirming signal back that the operation was performed A
terminal strip has been provided for interfacing with external dry contact inputs as well as dry contact
relay outputs. The Air-Eagle XLT TRX is user-programmable for up eight network frequencies to allow
multiple systems to operate simultaneously in the same area.
INSTALLATION
1. DISCONNECT power from all equipment before proceeding with installation.
2. Mount the transceiver in a convenient location.
3. Install input and output wiring to terminal strip.
4. Attach rubber duck antenna or coax from external antenna to connector on side of enclosure.
5. Connect supplied power input cable to your external power source.
APPROVALS
United States (FCC)
MCQ-XBPSX
Canada (IC)
1846A-XBPSX
Australia
RCM
Brazil
ANATEL 05774-16-01209

461-40800-DC
3
GENERAL OPERATION
Contact closures on inputs 1 thru 8 in the control transceiver transmit to activate relays #1 thru #8 in the
remote transceiver. Inputs from the remote equipment provide closures to remote transceiver that
transmit to energize relays 1 thru 8 in the control transceiver.
Input Activated
Action
1
Transmits Channel 1 command to remote unit.
2
Transmits Channel 2 command to remote unit.
3
Transmits Channel 3 command to remote unit.
4
Transmits Channel 4 command to remote unit.
5
Transmits Channel 5 command to remote unit.
6
Transmits Channel 6 command to remote unit.
7
Transmits Channel 7 command to remote unit.
8
Transmits Channel 8 command to remote unit.
Input Code Received
Action
1
Relay #1 energizes, maintained momentary.
2
Relay #2 energizes, maintained momentary.
3
Relay #3 energizes, maintained momentary.
4
Relay #4 energizes, maintained momentary.
5
Relay #5 energizes, maintained momentary.
6
Relay #6 energizes, maintained momentary.
7
Relay #7 energizes, maintained momentary.
8
Relay #8 energizes, maintained momentary.

461-40800-DC
4
TERMINAL STRIP WIRING
Relay Outputs
Terminal 1
N/O Relay #1
Terminal 10
N/O Relay #4
Terminal 19
N/O Relay #7
Terminal 2
C Relay #1
Terminal 11
C Relay #4
Terminal 20
C Relay #7
Terminal 3
N/C Relay #1
Terminal 12
N/C Relay #4
Terminal 21
N/C Relay #7
Terminal 4
N/O Relay #2
Terminal 13
N/O Relay #5
Terminal 22
N/O Relay #8
Terminal 5
C Relay #2
Terminal 14
C Relay #5
Terminal 23
C Relay #8
Terminal 6
N/C Relay #2
Terminal 15
N/C Relay #5
Terminal 24
N/C Relay #8
Terminal 7
N/O Relay #3
Terminal 16
N/O Relay #6
Terminal 8
C Relay #3
Terminal 17
C Relay #6
Terminal 9
N/C Relay #3
Terminal 18
N/C Relay #6
Contact Inputs
Terminal 1
Common Input 1
Terminal 7
Common Input 4
Terminal 13
Common Input 7
Terminal 2
Input 1
Terminal 8
Input 4
Terminal 14
Input 7
Terminal 3
Common Input 2
Terminal 9
Common Input 5
Terminal 15
Common Input 8
Terminal 4
Input 2
Terminal 10
Input 5
Terminal 16
Input 8
Terminal 5
Common Input 3
Terminal 11
Common Input 6
Terminal 17
Not Used
Terminal 6
Input 3
Terminal 12
Input 6
Terminal 18
Not Used
AC Power Inputs
Terminal 1
100-250VAC
Terminal 2
100-250VAC

461-40800-DC
5
RELAY & FREQUENCY SETUP
The unit is shipped from the factory
with SEL1 switches in the open
positions. All eight relays will operate
as maintained momentary and unit is
receiving commands on frequency
one. If you wish to change these
default settings, follow the instructions
below:
1. *IMPORTANT*
Disconnect power from unit.
2. Remove top cover.
3. Select desired relay operation
and/or frequency using the
table.
4. Reattach cover.
5. Reconnect power to unit.
6. Programming is complete.
RELAY CONFIGURATION
SEL1
SW#
OPEN (default)
CLOSED
SW1
Relays #1 - #8
maintained momentary
Relays #1 - #8
toggle latch
Maintained Momentary –Relay mimics button or input –
when depressed or closed, relay will be energized; when
released, relay de-energizes.
Toggle Latch –Relay changes and holds its state each time
the corresponding button or input is depressed or closed.
SW3
Main
Secondary
Important! When using more than one transceiver, they will
function better if one is set to Main and the other to
Secondary.
SW4
Repeater Mode OFF
Repeater Mode ON
FREQUENCY SETUP
NETWORK
FREQUENCY
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
Note –SW2 & SW9 not used on this model

461-40800-DC
6
SPECIFICATIONS
Power Supply
9-36 VDC, 10W
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC per channel
Fuse Protected
2 amp
Frequency
900 MHz Spread Spectrum
Transmitter Data
Eight Dry Contact Inputs
Transceiver Range
Up to 1 mile with Rubber Duck antenna.
Up to 10 miles with external antenna. *
RF Networks
Eight Independent Network Frequencies
RF Output Power
1W
Operating Temperature
-40oF to +185oF
Enclosure
Hinged fiberglass with window (NEMA 3, 3R, 4, 12, 13)
*Note: Max range statements are estimates based on a clear line of sight with few
interferences. Actual range will vary based on transmitting power, orientation of
transmitter and receiver, height of transmitting and receiving antennas, weather
conditions, electronic interference, terrain, and physical obstacles, including but not
limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills,
mountains).
ACCESSORIES
STANDARD ANTENNA (INCLUDED)
900MHz TNC Portable “Rubber Duck” Antenna
49-1103
MOBILE/BASE ANTENNAS (OPTIONAL)
Used to help achieve max range in non-line-of-sight and line-of-sight applications.
Contact BWI Eagle for recommendations.
900MHz Thru-Hole/Bracket Mount Mobile Antenna
49-2101
900MHz Magnet Mount Mobile Antenna
49-2102
900MHz Omni Directional Base Antenna
49-3101
900MHz Yagi Directional Base Antenna
49-3102
HIGH QUALITY COAX CABLE
Used to connect external antennas to control unit.
Flex Coax Cable w/Connectors
(Available in 5’, 15’, 25’, 30’, 40’, 60’, 80’, and 100’ lengths)
49-4000-XX
(XX = length in feet)
BULKHEAD EXTENSION
Used to provide an external antenna connection when mounting control unit
inside another enclosure.
TNC Male to TNC Bulkhead Cable Assembly
(Available in 2’, 4’, and 7’ lengths)
49-5004-X-ISO
(X = length in feet)

461-40800-DC
7
DIMENSIONS