BWI Eagle AIR-EAGLE SR PLUS 36-6000-DC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR PLUS
2.4 GHz RF Transceiver
MODEL 36-6000-DC
DESCRIPTION
The AIR-EAGLE SRPLUS TRX is an R.F. transceiver capable of
transmitting and receiving commands from up to 600 feet away. This
model comes equipped with three dry contact inputs and two 5amp
relay outputs. When combined with another transceiver this allows the
user to transmit information out and receive a confirming signal back
that the operation was performed. This unit has eight user-selectable
network frequencies to allow multiple systems to operate
simultaneously in the same area without interference.
INSTALLATION
DISCONNECT Power from all equipment before installation.
1. Mount the control unit in a convenient location.
2. Install control wiring to terminalstrip.
3. Make desired relay,channel code and frequency selections using
instructions on page 2.
4. Attach antenna to TNCconnector located on the right side on the
enclosure.
5. Connect supplied power input cable to your external source.
PC BOARD SET-UP INFORMATION
Make the following connections on the PC Board Terminal Strip (TER1)
TERMINAL STRIP WIRING (TER1)
Terminal 1
Negative (-) 9-36VDC INPUT
Terminal 2
Positive (+) 9-36VDC INPUT
Terminal 3
CH1 Dry Contact Input (Common)
Terminal 4
CH1 Dry Contact Input
Terminal 5
CH2 Dry Contact Input (Common)
Terminal 6
CH2 Dry Contact Input
Terminal 7
CH3 Dry Contact Input (Common)
Terminal 8
CH3 Dry Contact Input
Terminal 9
CH1 Relay N/O
Terminal 10
CH1 Relay C
Terminal 11
CH1 Relay N/C
Terminal 12
CH2 Relay N/O
Terminal 13
CH2 Relay C
Terminal 14
CH2 Relay N/C
CONTROLS & INDICATORS
POWER/TX LED
Illuminates Green when power is applied,
changes to Red when transmitting.
LED1
Green LED illuminates continuously while relay
#1 is energized
LED2
Green LED illuminates continuously while relay
#2 is energized
CH1 –CH3 Dry
Contact Inputs
Transmit individual RF codes to the remote
transceiver
REL1 & REL2
Two SPDT output control relays
RF1
RF Module that transmits/receives data for
corresponding unit

AIR-EAGLE®SR PLUS
2.4 GHz RF Transceiver
MODEL 36-6000-DC
RELAY, CHANNEL CODES & FREQUENCY
SETTINGS
The unit is shipped from the factory with SEL1 switches in the open
positions. The relays will operate as maintained momentary, the unit is
transmitting & receivingchannel 1 & 2 commands, and it is operating on
frequency 1. If you wish to change these default settings, follow the
instructions on the table below.
1) Remove power from unit.
2) Remove top cover.
3) Select desired relay operation, channel codes to be sent & received
and network frequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
RELAY CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW1
Relay #1 momentary (default)
Relay #1 toggle/latch
SW2
Relay #2 momentary (default)
Relay #2 toggle/latch
Maintained Momentary –Relay mimics button or input –when
depressed or closed, relay will be energized; when released, relay de-
energizes
Toggle Latch –Relay changes (and holds) its state each time the
corresponding button or input is depressed or closed.
CHANNEL CODE SET-UP
SEL1
(SW3-4)
Channel Codes To
Be Transmitted &
Received
SW3
SW4
1 & 2 (default)
OPEN
OPEN
3 & 4
CLOSED
OPEN
5 & 6
OPEN
CLOSED
7 & 8
CLOSED
CLOSED
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
DIMENSIONS
APPROVALS
United States (FCC)
OUR-XBEEPRO
Canada (IC)
4214A-XBEEPRO
Europe (CE)
ETSI
SPECIFICATIONS
Power Input
9 –36 VDC @ 10 Watts
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC
Fuse Protected
1 amp
Transceiver Frequency
2.4 GHz Spread Spectrum
RF Output Power
60 mW
Transceiver Range
Up to 600 feet
Note: Max range figures are estimates, based on free-air terrain with limited sources of
interference. Actual range will vary based on transmitting power, orientation of transmitter
and receiver, height of transmitting antenna, height of receiving antenna, weather
conditions, interference sources in the area, and terrain between receiver and transmitter,
including, but not limited to, indoor and outdoor structures such as walls, metal objects,
trees, buildings, hills, and mountains.
RF Networks
Eight Independent Frequencies
Antenna Connection
TNC Bulkhead
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
Weight
Approx 2 lbs.

AIR-EAGLE®SR PLUS
2.4 GHz RF Transceiver
MODEL 36-6000-DC
ACCESSORIES
Standard Antenna (Included):
2.4GHz TNC “Rubber Duck” Antenna
49-1201
High Gain Antennas –
Used to help achieve max range in both non line of sight and line
of sight applications. - Contact BWI Eagle for recommendations
2.4GHz Thru-Hole Mount Omni Directional Antenna
49-2201
2.4GHz Magnet Mount Omni Directional Antenna
49-2202
2.4GHz Omni Directional Antenna
49-3201
2.4GHz Yagi Antenna
49-3202
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available
in 5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of Feet)
Bulkhead Extensions –
Used to provide an external antenna connection when mounting
control unit inside another enclosure
TNC Male to TNCBulkhead Cable Assembly
- Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
(X = # of Feet)
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants theAir-Eagle Remote ControlSystem, if properly
used and installed, will be free from defects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improperinstallation, or improper
testing. This limitedwarranty, and any implied warranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitnessfor
a particular purpose. BWI Eaglemakes noexpress warranties beyond
thosestated here. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss duringshipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 10/25/2020 / PRODUCT REV. 6
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com