BWI Eagle 36-1400-BAT User manual

AIR-EAGLE SR PLUS
36-1400-BAT
2.4 GHz RF Transmitter
Document Date: 7/11/2023
Product Rev: 6

36-1400-BAT
1
WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and installed, will be free
from defects in material and workmanship for a period of 1 year after date of purchase. Said warranty to
include the repair or replacement of defective equipment. This warranty does not cover damage due to
external causes, including accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper testing. This limited
warranty, and any implied warranties that may exist under state law, apply only to the original purchaser of
the equipment, and last only for as long as such purchaser continues to own the equipment. This warranty
replaces all other warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express warranties beyond
those stated here. BWI disclaims without limitation, implied warranties of merchantability and fitness for a
particular purpose. Some jurisdictions do not allow the exclusion of implied warranties so this limitation
may not apply to you. To obtain warranty service, contact BWI Eagle for a return material authorization.
When returning equipment to BWI Eagle, the customer assumes the risk of damage or loss during
shipping and is responsible for the shipping costs incurred.
SIGNAL RANGE
Max range statements are estimates based on a clear line of sight with few interferences. Actual range will
vary based on transmitting power, orientation of transmitter and receiver, height of transmitting and
receiving antennas, weather conditions, electronic interference, terrain, and physical obstacles, including
but not limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills, mountains).
WIRELESS STOP, ASTOP, and E-STOP SYSTEMS
Wireless E-STOP systems should never be considered a primary life-saving device.
At least one hard-wired switch must be available in the event the wireless system is
not operational. Failure to comply may result in serious injury or death to personnel
and damage to equipment.
Wireless STOP and ASTOP transmitters are not failsafe emergency stop controls.
They are NOT to be used as a life-saving device. They are designed for wireless
control of equipment or vehicle remote operation. Failure to use as intended may
result in serious injury or death to personnel and damage to equipment.

36-1400-BAT
2
INTRODUCTION
The Air-Eagle SR Plus is an RF system designed for short to medium range wireless remote control of
electrical apparatus in a variety of industrial applications. Systems can consist of any number of receivers
and handheld or contact input transmitters working together to create a short to medium range radio
frequency system that operates hazardous or hard-to-reach equipment from safe, convenient locations.
Eight user selectable frequencies allow multiple systems to be used in the same area without
interference.
This transmitter is equipped to send four independent dry-contact input commands to an Air-Eagle SR
Plus receiver located up to 600 feet away. Longer ranges can be achieved with external antennas (See
ACCESSORIES section). The Air-Eagle SR Plus transmitter utilizes spread-spectrum technology and
provides the utmost in security and reliability.
INSTALLATION
1. Remove batteries from unit.
2. Mount the transmitter in a convenient location.
3. Install input control wiring to the terminal strip. (See TERMINAL STRIP WIRING section.)
4. Attach rubber duck antenna or coax from external antenna to connector on side of enclosure.
5. Install 2 AA lithium batteries.
GENERAL OPERATION
A closure on any input transmits its channel command to activate the corresponding relay in the remote
receiver. The transmission continues as long as the input is closed and ceases when the input opens.

36-1400-BAT
3
TERMINAL STRIP WIRING
Terminal 1
CH1 Dry Contact Input (Common)
Terminal 2
CH1 Dry Contact Input
Terminal 3
CH2 Dry Contact Input (Common)
Terminal 4
CH2 Dry Contact Input
Terminal 5
CH3 Dry Contact Input (Common)
Terminal 6
CH3 Dry Contact Input
Terminal 7
CH4 Dry Contact Input (Common)
Terminal 8
CH4 Dry Contact Input
Terminal 9
Not used on this model.
Terminal 10
APPROVALS
United States (FCC)
MCQ-XBEE3
Canada (IC)
1846A-XBEE3
Europe (CE)
ETSI
Australia
RCM
Brazil
ANATEL 06329-18- 01209

36-1400-BAT
4
FREQUENCY & DIGITAL ADDRESS SET-UP
The unit is shipped from the factory
with all SEL1 and SEL2 switches in
the open positions. It is operating
on Frequency 1 and Digital
Address 1. To change default
settings, follow the instructions
below:
*Note –only change the digital
address if using with a digitally
addressable receiver. Otherwise,
the digital address must be kept at
the default of Digital Address 1.
1. *IMPORTANT*
Disconnect power from
unit.
2. Remove top cover.
3. Select desired frequency
and/or digital address
using the table.
4. Reattach cover.
5. Reconnect power to unit.
6. Programming is complete.
FREQUENCY SETUP (SEL1)
NETWORK
FREQUENCY
SW1
SW2
SW3
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
Note - SEL1 SW4 not used on this model. Leave in OPEN
position
DIGITAL ADDRESS SETUP (SEL2)
DIGITAL
ADDRESS
SW1
SW2
SW3
SW4
1 (default)
OPEN
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
OPEN
3
OPEN
CLOSED
OPEN
OPEN
4
CLOSED
CLOSED
OPEN
OPEN
5
OPEN
OPEN
CLOSED
OPEN
6
CLOSED
OPEN
CLOSED
OPEN
7
OPEN
CLOSED
CLOSED
OPEN
8
CLOSED
CLOSED
CLOSED
OPEN
9
OPEN
OPEN
OPEN
CLOSED
10
CLOSED
OPEN
OPEN
CLOSED
11
OPEN
CLOSED
OPEN
CLOSED
12
CLOSED
CLOSED
OPEN
CLOSED
13
OPEN
OPEN
CLOSED
CLOSED
14
CLOSED
OPEN
CLOSED
CLOSED
15
OPEN
CLOSED
CLOSED
CLOSED
16
CLOSED
CLOSED
CLOSED
CLOSED
Note - SEL2 SW5-7 not used on this model. Leave in OPEN
position

36-1400-BAT
5
CONTROLS & INDICATORS
POWER/TX
LED1
Dual color LED illuminates red while unit is booting up, changes to green
when boot-up is successful and unit is ready to operate.
If this LED fails to turn green, power unit off for 15-20 seconds, then
reapply power.
Input Channels
1-4
Transmits individual RF codes to the receiver.
SEL1
Dip switch bank for frequency selection.
SEL2
Dip switch bank for digital address selection.
RF2
RF module that transmits data.

36-1400-BAT
6
SPECIFICATIONS
Power Supply
3.0 VDC
Battery Type
(2) 1.5V lithium or alkaline AA, total 3.0VDC nominal
Battery Life (active use)
Approximately 3 months
Battery Life (idle)
Up to 1 year
Transmit Data
Four Independent Dry Contact Inputs
Frequency
2.4 GHz Spread Spectrum
RF Output Power
60 mW
Range
Up to 600 feet *
RF Networks
Eight Independent Network Frequencies
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
*Note: Max range statements are estimates based on a clear line of sight with few
interferences. Actual range will vary based on transmitting power, orientation of
transmitter and receiver, height of transmitting and receiving antennas, weather
conditions, electronic interference, terrain, and physical obstacles, including but not
limited to; walls, building structures, trees (foliage), metal objects, and landscape (hills,
mountains).
ACCESSORIES
STANDARD ANTENNA (INCLUDED)
2.4GHz TNC Portable “Rubber Duck” Antenna
49-1201
MOBILE/BASE ANTENNAS (OPTIONAL)
Used to help achieve max range in non-line-of-sight and line-of-sight applications.
Contact BWI Eagle for recommendations.
2.4GHz Thru-Hole/Bracket Mount Mobile Antenna
49-2201
2.4GHz Magnet Mount Mobile Antenna
49-2202
2.4GHz Omni Directional Base Antenna
49-3201
2.4GHz Yagi Directional Base Antenna
49-3202
HIGH QUALITY COAX CABLE
Used to connect external antennas to control unit.
Flex Coax Cable w/Connectors
(Available in 5’, 15’, 25’, 30’, 40’, 60’, 80’, and 100’ lengths)
49-4000-XX
(XX = length in feet)
BULKHEAD EXTENSION
Used to provide an external antenna connection when mounting control unit
inside another enclosure.
TNC Male to TNC Bulkhead Cable Assembly
(Available in 2’, 4’, and 7’ lengths)
49-5004-X-ISO
(X = length in feet)

36-1400-BAT
7
DIMENSIONS