BWI Eagle AIR-EAGLE XLT 44-10100-120I-AC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 44-10100-120I-AC
DESCRIPTION
The AIR-EAGLE XLT TX Is an R.F. transmitter capable of sending a
single 120VAC input command to an Air-Eagle XLT Receiver located
up to 2500 feet away. Any number of transmitters and receivers can be
combined to create a medium range radio frequency system that
operates hazardous or hard-to-reach electrical apparatus from safe,
convenient locations. Seven user-selectable frequencies allow multiple
systems to operate simultaneously in the same area without
interference.
APPROVALS
United States (FCC)
MCQ-XB900HP
Canada (IC)
1846A-XB900HP
INSTALLATION
DISCONNECT AC Power from all equipment before installation.
1. Mount the AIR-EAGLE XLT TRANSMITTER in a convenient location.
2. Install wiring to input terminal strip
3. Install antenna. The unit has an antenna connector located on the
right side on the enclosure. Attach the supplied portable antenna to
this connector.
4. Connect AC power to the proper terminals in your control circuit.
TERMINAL STRIP WIRING
TER 3
DRY CONTACT
INPUT
TER 2
RELAY OUTPUT
TER 1
AC/DC POWER INPUT
1
120VAC N
1
Not Used
1
100-250 VAC
2
120VAC H
2
Not Used
2
100-250 VAC
3
Not Used
3
Ground
GENERAL OPERATION
When 120VAC appears on the input the unit transmits to energize relay 1
(or another relay as selected by the channel code transmitted) in any
receiver within transmit range. The signaltransmits continuously as long
as thevoltageis present and ceases whenvoltageis removed.
Dimensions (with mounting plate) 7.07L x 3.57W x 1.62H
CONTROLS AND INDICATORS
Power –LED1
Illuminates green when unit is powered
TX –LED2
Illuminates red when unit is transmitting
Relay –LED3
Not used on this model
RF1
RF module that sends data to the remote
receiver
SEL1
Seven dip switches forselecting options and
network frequency
TER3
120VAC input
TER2
Relay output
TER1
Power Input

AIR-EAGLE®XLT
900 MHz RF Transmitter
MODEL 44-10100-120I-AC
CHANNEL CODE & FREQUENCY SET-UP
The unit is shipped from the factory with all SEL1 switches in the open
positions. By default it is transmitting Channel #1code and operating on
Frequency #1. If you wish to transmit a different channel code or and/or
change the frequency, follow the instructions on the table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired channel code and/orfrequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
CHANNEL SELECTION SET-UP
SEL1 (SW1-4)
Channel
Code To Be
Transmitted
SW1
SW2
SW3
SW4
1 (default)
OPEN
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
OPEN
3
OPEN
CLOSED
OPEN
OPEN
4
CLOSED
CLOSED
OPEN
OPEN
5
OPEN
OPEN
CLOSED
OPEN
6
CLOSED
OPEN
CLOSED
OPEN
7
OPEN
CLOSED
CLOSED
OPEN
8
CLOSED
CLOSED
CLOSED
OPEN
9
OPEN
OPEN
OPEN
CLOSED
10
CLOSED
OPEN
OPEN
CLOSED
11
OPEN
CLOSED
OPEN
CLOSED
12
CLOSED
CLOSED
OPEN
CLOSED
13
OPEN
OPEN
CLOSED
CLOSED
14
CLOSED
OPEN
CLOSED
CLOSED
15
OPEN
CLOSED
CLOSED
CLOSED
16
CLOSED
CLOSED
CLOSED
CLOSED
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
SPECIFICATIONS
AC Input
100-250VAC, 5 W, 50/60 Hz
Transmitter Frequency
900 MHz Spread Spectrum
RF Output Power
250 mW
Transmit Range
Approximately 2500 Feet
Transmit Data
120VAC Input
Transmitter Channels
7 Independent Network Frequencies
Antenna Connection
TNC Female Connector
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate NEMA 4, 12, 13 –IP66
Weight
Approx 2 lbs.
DIMENSIONS
REPLACEMENT PARTS & ACCESSORIES
PC Board (Main)
44-10102-120I-AC
Standard Antenna (Included):
900MHz Portable Antenna (For distances up
to 2500 feet*)
49-1103
Optional Antennas and Accessories:
900MHz Omni Directional Antenna (For
distances up to 2 miles*)
49-3101
900MHz 13dB Yagi Antenna
Long Range Operation (For distances up to
4 miles*)
49-3102
Flex Coax Cable w/Connectors
49-4000-XX
(XX = # of Feet)
2 Ft. Bulkhead Assembly (Used when
mounting unit inside another enclosure)
49-5004-2-ISO
* = Line of Sight
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and
installed, will be free from defects in material and workmanship for a period of 1 year
after date of purchase. Said warranty to include the repair or replacement of defective
equipment. This warranty does not cover damage due to external causes, including
accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, andany implied warranties that may exist under state
law, apply only to the original purchaser of the equipment, and last only for as long as
such purchaser continues to own the equipment. This warranty replaces all other
warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express
warranties beyond those stated here. BWI disclaimswithout limitation, implied
warranties of merchantability and fitness for a particular purpose. Some jurisdictions
do not allow the exclusion of implied warranties so this limitation may not apply to
you. To obtain warranty service, contact BWI Eagle for a return material
authorization. When returning equipment to BWI Eagle, the customer assumes the
risk of damage or loss during shipping and is responsible for the shipping costs
incurred.
DOCUMENT DATE: 08/05/19 / PRODUCT REV. 6