Cal-Royal 801 Series User manual

801 SERIES DOOR CLOSER
SUPER RIGID PARALLEL ARM
INSTALLATION INSTRUCTION FOR CAL-ROYAL 801 SERIES DOOR CLOSER
(HOLD-OPEN & NON HOLD-OPEN TYPE)
Model No. SPAS/900 (NON HOLD-OPEN)
HOSRPS/900 ( HOLD-OPEN)
DOOR SELECTION
PULL SIDE
PUSHSIDE
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
PARALLEL ARM MOUNTING (Push Side)
Hinge Edge of Door
LEFT HAND DOOR-LH
RIGHT HAND REVERSE-RHR
RIGHT HAND DOOR-RH
LEFT HAND REVERSE-LHR
Hinge Edge of Door
GENERAL DESCRIPTIONS:
The 801 series closer are non-handed for right or left hand doors
designed to meet entrance accessibility requirements. The 801 series
are spring power adjustable for all exterior/interior door up to 58"
(1470mm) wide doors and up to 330 Lbs (150Kg.) weight.
Adjust the spring power before installing the door closer according to
the "POWER ADJUSTMENT CHART FOR DOOR SELECTION" as
shown on page. 4
The 801 series closer are installed BACK CHECK function as a standard
which is essential to the proper operation of the SUPER RIGID
PARALLEL ARM. Use just enough to prevent arm striking stop
with impact.
The delayed action (optional) function can not be used for this arm
because this arm permits maximum 100° door open angle.
Closing Speed Control
Back Check Control
Standard Closing Cycle
CLOSED
Starting Point
T
o
B
A
C
K C
H
E
C
K
C
l
o
s
i
n
g
L
a
t
c
h
O
P
E
N
I
N
G
':*'&*0263APR

STOP
PARALLEL ARM (PUSH SIDE) MOUNTING
LEFT HAND DOOR SHOWN
8-916" (217mm)
1-14"
(32mm)
12"
(304.8mm)
2-1516"
(75mm)
STOP
FACE
DOOR
EDGE
BRACKET
CLOSING
LATCH
SPRING
I
n
c
r
e
a
s
e
D
e
c
r
e
a
s
e
4mm
Hex
Power
Adjustment
Nut
FILLER
PLUG
BRACKET
5/16"or 8mm
HEX
WRENCH
ARM STOP
Power Adjustment Chart
MAXIMUM DOOR WIDTH
TURNS
REQUIRED
6 TURNS C.C.W.
INTERIOR
DOORS
8.5 lb-f
EXTERIOR
DOORS
34"(864)
8.5 lb-f 3 TURNS C.C.W.
PRESET
3 TURNS C.W.
7 TURNS C.W.
12 TURNS C.W.
38"(962)
48"(1219)
54"(1372)
60"(1524)
30"(762)
36"(914)
42"(1067)
48"(1219)
DOOR
34"(19mm)
1-1116"(43mm)
1-116"(27mm)
716"(11mm)
25 32"(20mm)
FILLER
PLUG
BRACKET
5/16"or 8mm
HEX
WRENCH
ARM STOP STOP
8-916" (217mm)
1-14"
(32mm)
12"
(304.8mm)
2-1516"
(75mm)
STOP
FACE
DOOR
EDGE
BRACKET
CLOSING
LATCH
SPRING
DOOR
34"(19mm)
1-1116"(43mm)
1-116"(27mm)
716"(11mm)
25 32"(20mm)
1
2
Slow
Fast
L
Slow
Fast
Increase
Decrease
Slow
Fast
C
DB
PARALLEL ARM (PUSH SIDE) MOUNTING
RIGHT HAND DOOR SHOWN
INSTALLATION INSTRUCTIONS
CUSH ARM, CUSH HOLD OPEN ARM
':*'&*0262/3APR

5/16 OR 8mm
HEX WRENCh
THE HAND MUST BE CORRECT BEFOR THE BRACKET IS MOUNTED
TO THE DOOR STOP (TOP JAMB).
Refer to page 1.
FOR LEFT HAND DOORS:
All bracket are shipped assembled for LEFT HAND DOOR. Insert 5/16"
(8mm) hex wrench into ARM STOP and turn anti-clockwise to seat as tightly
as possible.
Push filler plug in firmly.
FOR RIGHT HAND DOORS:
Push filler plug out of bracket
Using a 5/16" (8mm) hex wrench turn ARM STOP clockwise to remove from
bracket insert in hole marked "R". Turn hex wrench clockwise to seat ARM
STOP as tightly as possible. Push filler into other hole.
BRACKET
ARM STOP
FILLER PLUG
INTERCHANGEBLE FOR DOOR HANDING
CAUTION
IMPROPER INSTALLATION OR REGULATION
MAY RESULT IN PERSONAL INJURY OR
PROPERTY DAMAGE. FOLLOW ALL
INSTRUCTIONS CAREFULLY.
HOLD OPEN CONTROL
HANDLE (HOLD OPEN ARM)
stud
FOREARM
MAIN ARM
COVER
SHAFT
SCREW
DELAYED
VALVE
CLOSING SPEED
VALVE
INSTALLATION SEQUENCE
LEFT HAND DOOR SHOWN - RIGHT HAND DOOR OPPOSITE
IMPORTANT REMARK
1. Using template dimensions shown above, mark FOUR (4) HOLES
ON DOOR for door closer and THREE (3) HOLES
ON FRAME for parallel bracket.
2. Mount closer on door using screws provided. SPEED ADJUSTING
VALVE MUST POSITIONED TOWARD AWAY FROM HINGE
EDGE.
3. Adjusting spring power to match door width or weight as indicated
by Power Adjustment Chart shown on page 2.
4. Mount closer on door to dimensions shown on page 2.
ADJUSTABLE BACK CHECK FUNCTION
Do not allow door to slam into frame.
A normal standard closing time from 90º open position is 5 to 7
second evenly divided between main closing (sweep) speed and
latching speed Adjust the CLOSING speed first, then adjust the
LATCHING speed.
This function is essential to the proper operation of the SUPER
RIGID PARALLEL ARM. Use just enough to prevent arm to striking
stop with impact. See page 2.
ATTACH COVER
Install cover securely using screw provided.
HOW TO HOLD-OPEN (90° STOP)
A quarter turn on the HOLD-OPEN CONTROL HANDLE engages or
disengages hold-open.
HOLD
OPEN
LATCHING
SPEED
VALVE
BACKCHECK
VALVE
INSTALLATION INSTRUCTIONS:
':*'&*0263/3APR