Calibre Fitness CF-FID User manual

MULTI-ANGLE BENCH
Owner’s Manual
CF-FID

2
Important Safety Information 3
7-4ylbmessA
8tsiLstraP
9weiVdedolpxE
Table of Contents

Important Safety Information
3
Prior to assembly, remove components from the box and verify that all the listed parts were
supplied.
WARNING!
Before using this unit or starting any exercise program, consult your
physician. This is especially important for persons over the age of
35 and/or persons with pre-existing health problems. The
Products LP assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit
have read the Owner’s Manual and are familiar with safety informa-
tion and precautions.
SAFETY PRECAUTIONS
• This unit should only be used on a level surface and is intended for
indoor use only. We recommends an equipment mat be
placed under the unit to protect the floor or carpet and for easier
cleaning.
• Wear comfortable, good-quality walking or running shoes and
appropriate clothing. Do not use this unit with bare feet, sandals,
socks or stockings!
• Always examine your unit before using to ensure all parts are in
working order.
• Do not leave children unsupervised near or on the unit.
NOTE:Hand tighten bolts and nylon nuts until machine is fully assembled.

Assembly
4

NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
STEP 1 Connect Main Frame (1) to U Front Base (2) with Bolts
(19), Washers (13) and Nylon Lock Nuts (14).
Connect Main Frame (1) to Rear Base (3) with Bolts (15),
Washers (13) and Nylon Lock Nuts (14).
Screw Knob (26) into Main Frame (1) underside. This
Knob is used to tighten down any attachment used in your
Bench.
Assembly
5

NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
STEP 2
STEP 3
STEP 4
Connect Seat Pad (9) to Seat Support Frame (4) using
Bolts (17) and Washers (18).
Slide Pin (10) down into Main Frame (1) and secure with
Washer (13) and Nylon Lock Nut (14). Connect Spring
(24) between Main Frame (1) and Pin (10).
Connect Seat Support Frame (4) to Main Frame (1) using
Bolt (12), Washers (13) and Nylon Lock Nut (14). Seat
can then be adjusted by pulling Pin (10) toward rear of
unit.
Assembly
6

NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
STEP 5
STEP 6
STEP 7
Connect Back Pads (8 and 41) to Back Pad Support Frame (5)
using Bolts (17) and Washers (18). Connect Back Pad Support
Frame (5) to Main Frame (1) using Bolt (12), Washers (13 ) and
Nylon Lock Nut (14).
Connect Adjustable Back Pad Frame (6) to Back Pad Support
Frame (5) using Bolt (12), Washers (13) and Nylon Lock Nut (14).
Slide Bolt (12) through Adjustable Back Pad Frame (6) secure
Plastic Sleeve (7) with Washers (13) and Nylon Lock Nut (14).
Slide Roller Pad Tube (31) into Leg Support (29). Place
Upholstered Roller Pad (32) on each side of Roller Pad Tube (31)
- secure with Big Plugs (33). Attach Leg Support (29) to Main
Frame (1) using L Pin (34).
Assembly
7

Parts List
8
Ref # Part # Description Qty
202-00659 SCREW, BUTTON HEAD SOCKET CAP M8*25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
41
42
43
1
1
1
1
1
1
1
1
1
1
6
4
17
9
2
2
6
6
2
2
1
2
1
1
2
1
1
3
1
3
1
2
2
1
1
4
2
2
2
1
12
12
223-00879
223-00880
223-00881
223-00882
223-00883
223-00884
206-00400
228-00202
228-00203
210-00009
202-00026
202-00639
202-00222
202-00092
202-00640
206-00462
202-00637
202-00641
202-00657
206-00401
206-00052
206-00006
206-00400
202-00118
206-00036
210-00025
206-00114
206-00398
223-00908
206-00391
219-00537
206-00395
206-00390
210-00145
206-00278
202-00235
202-00091
202-00658
206-00402
PIN
SPRING
WHEEL
KNOB
MAIN FRAME
U FRONT BASE
REAR BASE
FRAME, SEAT PAD SUPPORT
FRAME, BACK PAD SUPPORT
FRAME, ADJUSTABLE BACK PAD
PLASTIC SLEEVE
BACK PAD, UPPER
SEAT PAD
IRON BUSHING, 25X12.2X8
SCREW, M12X125 BUTTON HEAD SOCKET CAP
WASHER, 13X26X2
NYLON NUT, M12
SCREW, M12X75 BUTTON HEAD SOCKET CAP
LEFT FOOT CAP 1, 50.8X76.2
SCREW, M10X70 BUTTON HEAD SOCKET CAP
WASHER, FLAT 23x11x2
SCREW, BUTTON HEAD SOCKET CAP M12X80
LEFT FOOT CAP 1, 50.8
SMALL GRIP
PLUG 40*80
BALL HEAD FOR PIN
PLASTIC SLEEVE, 50.8x44.5
PLUG 50.8X76.2
FRONT WEIGHT SLIDE HOLDER
SQUARE PLUG, 50.8 SERIES
FOAM TUBE, SERIES
FOAM PADDING, 100X22X180 SERIES
PLUG, ROLLER PAD TUBE CAP, SERIES
L PIN
RUBBER PAD
WASHER, 11X20X1.5
NYLON NUT, M10
SCREW, BUTTON HEAD SOCKET CAP M10X45
RIGHT FOOT CAP 2, 50.8
40200-822 DAPKCABREWOL
49000-202 6.1*61*9REHSAWTALF

Exploded View
9