Calibre Fitness CF-PC User manual

POWER CAGE
Owner’s Manual
CF-PC

2
Important Safety Information 3
7-4ylbmessA
8tsiLstraP
9weiVdedolpxE
01noitamrofnIytnarraW
Table of Contents

Important Safety Information
3
Prior to assembly, remove components from the box and verify that all the listed parts were
supplied.
WARNING!
Before using this unit or starting any exercise program, consult your
physician. This is especially important for persons over the age of
35 and/or persons with pre-existing health problems. The
Products LP assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
It is the owner’s responsibility to ensure that all users of this unit
have read the Owner’s Manual and are familiar with safety informa-
tion and precautions.
SAFETY PRECAUTIONS
• This unit should only be used on a level surface and is intended for
indoor use only. We recommends an equipment mat be
placed under the unit to protect the floor or carpet and for easier
cleaning.
• Wear comfortable, good-quality walking or running shoes and
appropriate clothing. Do not use this unit with bare feet, sandals,
socks or stockings!
• Always examine your unit before using to ensure all parts are in
working order.
• Do not leave children unsupervised near or on the unit.
NOTE:Hand tighten bolts and nylon nuts until machine is fully assembled.
Read all precautions and instructions in this manual before using this equipment.
!CAUTION

Assembly
4

STEP 1
Attach Rubber Pads (15) to underside of Base Frame (10).
Attach Uprights (1,2,3,4) to Base Frame (10) using:
8 x (21) Bolt M12x75
16 x (24) Washer M12
8 x (23) Nylon Lock Nut M12
Note: Numbers on Uprights should face inward toward center
of unit.
5
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly

STEP 2
Assemble Slide Holders (6,7,8,9) onto uprights as shown
above. Do not move on to STEP 3 before the Slide Holders
are attached correctly.
6
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly

Connect Top Frame to Uprights using:
2 x (12) Steel Plate
4 x (20) Bolt M12x100
4 x (21) Bolt M12x75
2 x (22) Bolt M12x95
20 x (24) Washer M12
10 x (23) Nylon Lock Nut M12
STEP 3
7
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly

8
Ref # Part # description Qty
1 223-00902 LEFT FRONT UPRIGHT 1
2 223-00903 RIGHT FRONT UPRIGHT 1
3 223-00904 RIGHT REAR UPRIGHT 1
4 223-00905 LEFT REAR UPRIGHT 1
5 223-00906 TOP FRAME 1
6 223-00907 REAR WEIGHT SLIDE HOLDER 2
7 223-00908 FRONT WEIGHT SLIDE HOLDER 2
8 223-00909 LEFT SLIDE CROSS WEIGHT HOLDER 1
9 223-00910 RIGHT SLIDE CROSS WEIGHT HOLDER 1
10 223-00911 BASE FRAME 1
11 219-00181 DIP BAR 2
12 219-00586 STEEL PLATE 2
13 210-00258 POP PIN 8
14 206-00327 PLASTIC SLEEVE, 63.5X88.9-50.8X76.2 16
15 206-00129 RUBBER PAD 4
16 206-00394 PLUG, 50.8X76.2 SERIES 2
17 206-00391 SQUARE PLUG, 50.8 SERIES 3
18 206-00389 HAND GRIP 2
19 219-00073 CLIP 2
20 202-00654 SCREW, BUTTON HEAD SOCKET CAP M12X100 4
21 202-00655 SCREW, BUTTON HEAD SOCKET CAP M12X75 12
22 202-00656 SCREW, BUTTON HEAD SOCKET CAP M12X95 2
23 202-00092 NYLON NUT, M12 18
24 202-00127 WASHER, 13*24*1.5 36
Parts List

9
Exploded View