CAME DIW 01 User manual

DIW 01
DIW 03-DIW04
INSTALLATION MANUAL
CORDLESS PHOTOCELL
Thissymbol indicates sectionstobe readwithparticular care.
Thissymbol indicates sectionsconcerningsafety
Thissymbol indicates notesto communicateto users.
with the following standards:
EN 12978, UNI EN 954-1, CEI EN 60335-1, UNI EN 12453.
“IMPORTANTSAFETY INSTRUCTIONSFORINSTALLATION”
“CAUTION:IMPROPERINSTALLATION MAY CAUSE
SERIOUSDAMAGE,FOLLOW ALLINSTALLATIONINSTRUC-
TIONSCAREFULLY”
“THISMANUALIS ONLY FORPROFESSIONALINSTALLERS
ORQUALIFIEDPERSONS”
Legend of symbols
Reference Standards
Description of devices
Designed and manufactured by CAME CANCELLI AUTOMATICI
S.p.A. in compliance with the safety regulations in force.S.p.A.
DIW01
Protection deviceMade up of two units:
-12/24v AC/DC Infrared receiver.
1 led to signal that battery is run down (when the led on the receiver
flashes, this means that the batteries’ charge will completely run
down in about a month)
-Battery powered infrared transmitter (works on four 1.5V AAA
batteries)
DIW04
- Infrared repeater, made up of a central photodiode receiver and
two lateral, transmitting photodiodes, with dip switches for selecting
the emitting side.
Battery powered (works on four 1.5V AAA batteries)
DIW03
- Infrared repeater, made up of a central transmitter photodiode and
two lateral receiver photodiodes, with dip switches for selecting
receiving side.
Battery powered (works on four 1.5 AAA batteries)
TX
TX RX
RX
RX TX
GB
GB

DIW01 (TX)
Description/Electrical connections and DIP switch
functions
1-Signalpresentwarningled
2-DipSwitch
DipSwitchfunction
Dipswitch1 in ON position=
12VAC/DCpower supply
Dipswitch1 in OFF position=
24VAC/DCpower supply
Dipswitch2 in OFF position=
Excludes testing of service
function
(tobeusedwhen
TS??Is not connected)
3- Low battery/open contact
warningled
4-Terminal board for con-
nections
DIW01 (RX)
Contatto N.O.
C1/C2/C3/C4
10
2
TS
2
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10 11 12
05 06 07 08 09 V1 V2 V3
05 06 07 08 09 V1 V2 V3
1,5V AAA
1,5V AAA
+
+
-
-
+
+
-
-
-
-
+
+
-
-
+
+
1,5V AAA
1,5V AAA
K
K
K
K
K
K
R13
R13
R15
R15
R22
R22
R23
R23
1
2
1-Battery housing
(four 1.5V AAA batteries)
2-Infrared led
-+-+
NO
NC
C
1
2
3
4
Before installing you must:
• Make sure that the line voltage is disconnected.
• See that the point, to which the equipment will be mounted,
is in an area protected from any impacts, that the mounting
surface is solid, and that the mounting on to the surface is
carried out with the proper hardware (bolts, pins, etc).
•Provide for proper electrical cable conduits making sure that
they are free from any mechanical damage.
InstallationTechnical data
Receiver/Transmitter/Repeater





Dimensions and holes pitch
DIW01 (TX)
Power supply: (4 1.5V AAA batteries)
Draw: 70 µA
Degree of protection: IP 54
Material: PC-ABS UL94V0 / Policarbonato / Marpram mar TPA1 65 NT
Working temperature:
#
#
DIW 01 (RX)
Power supply: 12/ 24 V A.C. - D.C.
Draw: 48 mA
Degree of protection: IP 54
Material: PC-ABS UL94V0 / Policarbonato / Marpram mar TPA1 65 NT
Working temperature: #
#
Ripetitore DIW04
Power supply: (4 1.5V AAA batteries)
Draw: 70 µA
Degree of protection: IP 54
Material: PC-ABS UL94V0 / Policarbonato / Marpram mar TPA1 65 NT
Working temperature:
#
#
RipetitoreDIW03
Power supply: (4 1.5V AAA batteries)
Draw: 70 µA
Degree of protection: IP 54
Material: PC-ABS UL94V0 / Policarbonato / Marpram mar TPA1 65 NT
Working temperature:
#
#
Fig.B
Fig.A

Example of a standard installation and relati-
ve Dip Switch configuration DIW01(TX)
Does NOT
require
configuration
DIW04 Repeater
DIW03 Repeater
1-Battery housing
(Four 1.5V AAA batteries)
2-Infrared led,
selectable through the DIP
switch
3-Low battery warning led
4-Dip switch for selecting
transmission led
WhenDipswitch1ON,left-hand
led is active
When Dip switch 2 ON, right-
hand led is active
1-Battery housing
(Four 1.5V AAA batteries)
2-Infrared led,
selectable through the DIP
switch
3-Low battery warning led
4-Dip switch for selecting
transmission led
When Dipswitch1ON,left-hand
led is active
When Dipswitch 2 ON, right-
hand led is active
+
+
-
-
+
+
-
-
-
-
+
+
-
-
+
+
K
K
K
K
K
K
2
1
1
4
2
3
+
+
-
-
+
+
-
-
-
-
+
+
-
-
+
+
K
K
K
K
K
K
2
1
1
2
4
3
DIW01(RX)
Does NOT
require
configuration
DIW04
Dip 1 set to ON
Dip 2 set to OFF
DIW03
Dip 1 set to OFF
Dip 2 set to ON
DIW01(RX)
DIW01(TX)
DIW01(TX)*
DIW01(RX)**
DIW04*
DIW03*
Assembly
Make sure that the distance between the two photocells is not
greater than 10 metres, and that they are perfectly aligned,
before installing. Now mount the bases of the photocells,
using proper screws that suit the attachment structure
(max.Ø 6 mm). Insert the batteries (you will need four 1.5V
AAAs) into the transmitter and the repeaters making sure
the polarity matches that shown on the card. Set the leds to
(ON/OFF) depending on the make up of the system. Fasten the
transmitters/repeater using the screws provided.
Carry out the connections for the receiver/s as shown in fig. B.
Note: When using DIW01, DIW03 and DIW04, as explained in
the two preceding configurations, remember to remove the
bridge on DIW01 (TX)
*With DB-L/DB-LN columns
**With G02802 photocell support
DIW04*
DIW03*
*With DB-L/DB-LN columns
DIW01(TX)
Does NOT
require
configuration
DIW01(RX)
Does NOT
require
configuration
DIW04
Dip 1 set to ON
Dip 2 set to OFF
DIW03
Dip 1 set to OFF
Dip 2 set to ON

Problems
- The led on the receiver is flashing: the transmitter battery is
run down
- The led on the receiver stays on: signal is interrupted due to
transmitter malfunction.
Demolition and disposal
Manufacturer’s declaration
Declaration of conformity
la CAME Cancelli Automatici S.p.A.
via Martiri della Libertà, 15
31030 Dosson di Casier - Treviso - ITALYtel
([phone] - fax [phone]
internet: www.came.it - e-mail: [email protected]
Declare under their own responsibility that the following
products for gate and garage door automation called:
Are compliant with essential requirements and with pertinent
regulations established by the following directives and to the
applicable parts of the standards listed below:
Electromagnetic compatibility directive 89/336/EEC - 92/31/EEC
Electrical equipment designed for use within certain voltage
limits directive 73/23/EEC - 93/68/EEC
Machinery directive 98/37/EC
EN 61000-6-2
EN 61000-6-3
EN 12978
EN 60529
EN 954-1
DIW01- DIW03-DIW04
L’amministratore delegato
Sig. Andrea Menuzzo
CAME CANCELLI AUTOMATICI S.p.A.
VIA MARTIRI DELLA LIBERTÀ 15
31030 DOSSON DI CASIER - TV - ITALY
www.came.it
Per assistenza e informazioni tecniche
.5-%2/6%2$%

Product disposal
Our products are made up of various types of materials. Most of
them (aluminium, plastics, iron,
electrical wires, etc.) may be disposed of in normal garbage
collection bins and can be recycled by disposing of in specific
recyclable material collection bins and disposal in authorized
centres.
Other components (electrical boards, remote control batteries,
etc.), however, may contain polluting substances.
They should therefore be removed and given to qualified service
companies for proper disposal.
Prior to disposal, it is always advisable to check specific
regulations in force in the place of disposal.
PLEASE DISPOSE OF PROPERLY!
Connecting DIW01 with DIR/DOC
Rx
TX 210 2 TX CNC
-
02C1
10 2C1
Tx
Rx
Tx
DIR DIR
24 0 TS CNC
-
DIW NO
DIW
24 0
02C1
10 2C1
Tx
Rx
Tx
DOC
24 0 TS CNC
-
DIW NO
DIW
24 0 N0 CNC
Rx
DIW01 with DIR
DIW01 with DOC
119RT88 v2