Cannondale Topstone Neo Lefty User manual

Topstone Neo w/ Lefty
Quick Start Guide
Applies to: Topstone Neo w/ Lefty

Welcome to the Cannondale family.
WARNING
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK
This is a Quick Start Guide, not an
Owner’s manual.
Bicycling is an active sport with
inherent risk. A wide range of injuries
are possible. Due to the nature of
bicycle riding, the situations you
encounter while riding, you will be
exposed to the risk of serious injury,
paralysis or death. This risk cannot
be eliminated. You can minimize
the risk in many ways. Begin by
reading the complete Charge Bicycle
Owner’s manual accompanying
this bike and available online at
www.chargebikes.com, particularly
section “IMPORTANT SAFETY
INFORMATION”.
First up, thank you for buying a new Cannondale bike – we’re excited to
have you on board and to get you out riding as soon as possible. Our new
assembly process is easy-to-follow – using methods outlined in this guide
to assemble your new Cannondale at home, plus it’s even easier to do so
with a friend. Our guide will take you through the simple steps from start
to nish – you can also follow along with a how-to video, as you build your
bike, just visit: [email protected]
If you still have any questions, then our Cannondale rider support sta are
ready to help you. Feel free to give us a call at
Also, when your new bike is all assembled and ready to ride, we’d love to
check it out – please don’t forget to tag #ridecannondale in your social
media. Enjoy the ride!

SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK

1.
Install your
handlebars

Install your
front wheel

Install your
pedals



This video applies to one Cannondale Platform:
• Topstone Neo with Lefty
Tools Needed:
• Flat-Head Screwdriver
• Phillips-Head Screwdriver
• Box Cutter
• Scissors
Tools Included:
• Torque Wrench
• Allen Keys
• Pedal Wrench
Gently lift your bike out of the box and set
it on top of the box. Make sure the attached
wheel is facing upwards
Use a at head screwdriver to carefully open the upper ap of the
box.
Prior to assembling your bike, review the pre-ride checklist and
Assembly Instruction Guide.
Conrm that a builder has completed the checklist.
Carefully lift the bike out of the box and set it onto the top of the box.
Remove the front wheel from the bike by carefully removing the zip
ties or Velcro, then remove all packaging from the wheel and set it
aside.
Remove all additional packaging from the bike.
A.

C.
D.

F.
D
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK

Lift the entire bike up o the box and set the
rear end into the standing box.
The front fork should rest over the edge of the
box.

Gently let the handlebar hang from the frame. Carefully lift and rotate
the bike, lowering it gentlyback into the boxwiththefork overhanging
the side of the box.
Inside the small box, you’ll nd parts essential for assembly, necessary
tools, component documentation and manuals.
Once the bike is assembled, but before you ride, please read the
owner’s manual.
Locate and remove the warrantycard and set it aside withthe owner’s
manual.
G.
H.
I.
J.
G
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK

 A
B
D
E
Using the included hex wrench, loosen and remove the bolts and
faceplate from the stem. The stem connects the handlebar to the
fork. Set the bolts and faceplate aside together, so you don’t lose
anything.
Place the handlebar into the stem and verify the brake hoses and
shift cables wrap around the frame cleanly, without visible kinks in
the lines.
Loosely reattach the faceplate to the stem. Take care to not tighten
one bolt more than another. The goal is a consistent gap between the
stem and faceplate.
Center the handlebar in the stem using the markings on the bar, then
roll the bars back into a comfortable position.
Hand-tighten the stem bolts using the 4mm hex wrench, ensuring
there’s an even gap between the stem body and faceplate at both
the top and bottom of the stem. You will fully tighten these later.
A.

C.
D.

SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK


Remove the disc brake pad spacer from the front caliper. Take care
not to pull the front brake lever while either the pad spacer or disc
brake rotor is not present in the caliper.
To install the front wheel, the brake caliper must be removed. Locate
the brake caliper on the Lefty Oliver, then locate the Stop Lock lever
in-front of the caliper (in the ‘closed’ position, as indicated by the
lock icon).
Flip the lever open, exposing the unlock symbol. The brake caliper is
now unlocked and can be removed.
Remove the brake caliper from the Lefty Oliver caliper mount.
Slide the Lefty front wheel on to the Lefty Oliver hub axle.
Using the included 5mm hex wrench, begin to tighten the wheel onto
the Lefty hub axle.
A.

C.
D.

F.
C
D
E
F
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK


Very rmly tighten the front wheel onto the Lefty Oliver. The wrench
should leave an imprint in your hand.
Install the front brake by rst locating the pins on the caliper. Guide
the pins onto the Lefty Oliver caliper mount. Ensure the brake rotor
is centered between the brake pads.
Lock the brake caliper into place by closing the Stop Lock lever.
Carefully lift and remove the bike from the box.
Remove the e-bike charger from the larger bicycle box and set it
aside. We’ll come back to it later.
Remove any additional packaging from the rear of the bicycle.
G.
H.
I.
J.

L.
H
I
I
J
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK


Pedals are left- and right-specic. Locate the left and right markings
on the pedal spindles prior to installation.
Locate the bag of grease and carefully insert the threaded portion of
the pedal spindle into the bag.
Insert the right pedal (marked with R) into the right/drive side crank
arm and tighten with your ngers. Repeat with the left pedal (with an
L on it). Please note: Both pedals tighten in the direction of the front
wheel.
Tighten both pedals down very rmly.
A.

C.
D.
A
B
C
D
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK

 A
B
 Ensure the front reector points straight ahead,
perpendicular to the ground.
The rear reector must point straight back.
Gently pull the wheel reectors toward the rim to ensure they are
braced by the spokes.
Adjust seat height by loosening the seatpost collar.
Standing next to the bike, position the saddle so it’s the same height
as your hip.
Align the saddle with the frame and tighten the seatpost clamp
When riding, you should have a slight bend in your knee when the
pedal is at the bottom of its rotation.
A.

C.
D.

F.
G.
D
G
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK


 Select the correct bit for the stem bolts and install it
into the torque wrench.
Look for the torque specication markings on the front and back
of the stem, as well as the seatpost. If these markings are absent,
torque all stem, seatpost and seat collar bolts to 7 Nm.
Tighten the stem bolts in an ‘X’ pattern and ensure the gap is even
between the stem and faceplate at all four bolts.
 Secure the front wheel between your legs and turn the
handlebar. If the handlebar and wheel move independently, the stem
bolts are not tight enough. Use the torque wrench and correct bit to
properly torque the bolts.
Attempt to rotate the handlebar forward and backward in the stem. If
it moves, the stem faceplate bolts are nottight enough. Usethe torque
wrench and correct bit to torque the faceplate bolts to specication,
using the same “X” pattern as before.
Grab the front and rear of the seat and attempt to tilt it on the seat
post head. It should not move.
H.
I.
J.

L.
M.
I
K
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK
L
J


  Conrm the Lefty front wheel is secure.
Reinstall the 5mm hex wrench and ensure the bolt is very tight ––
enough to denitely leave a mark in your hand.
Conrm the front and rear brakes engage when the
levers are squeezed.
The brake lever and handlebar should not come into contact with the
brakes fully engaged.
Tire Pressure. Inate the tires to the manufacturer’s recommended
tire pressure, marked on the tire sidewall.
N.
O.
P.
Q.
N
O
P
Q
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK


 Unbox the e-bike charger and remove any additional
packaging from the charger itself.
Read the instructions included with the charger, then assemble the
charger.
Prior to charging, conrm your e-bike is powered o and is propped
up against a stable surface or wall in a dry place.
Open the charge port, located near the head tube at the front of the
bike.
Carefully insert the charging cord into the charge port. Take care to
properly align the cord and port contacts.
A charging icon will appear on the handlebar display to conrm it is
charging.
R.

T.

V.
W.
S
U
V
W
SET-UP STEP 2STEP 1 STEP 3 PRE-RIDE CHECK

Welcome to the family.
@ridecannondale