Cannondale Adventure Neo Allroad S 2023 User manual

Applies to 2023 Cannondale Adventure Neo Allroad S. Models C68303U & C68303M.
Adventure Neo
Allroad S
Quick Start Guide

2
Welcome to the Cannondale family.
WARNING
This is a Quick Start Guide, not an
Owner’s manual.
Bicycling is an active sport with
inherent risk. A wide range of injuries
are possible. Due to the nature of
bicycle riding, the situations you
encounter while riding, you will be
exposed to the risk of serious injury,
paralysis or death. This risk cannot
be eliminated. You can minimize the
risk in many ways. Begin by reading
the complete Cannondale Bicycle
Owner’s Manual accompanying
this bike and available online at
cannondale.com/owners-manuals,
particularly sections “IMPORTANT
SAFETY INFORMATION” and “PART
3  ASSEMBLY”.
First up, thank you for buying a new Cannondale electric bike – we’re
excited to have you on board and to get you out riding as soon as possible.
Our Quick Start Guides provides basic use and operation instructions.
This quick start guide is not a replacement for your bicycles Cannondale
Owner’s Manual and other component manuals supplied with your bicycle.
Our guide will take you through charging the battery, battery removal/
installation, turning the bike on/o, using electric pedal assist, controlling
the lights, using the throttle, and using walk assist mode.
If you still have any questions, then our Cannondale rider support sta are
ready to help you. Feel free to Submit Your Question or give us a call at
18002453872 (BIKE USA)
If you haven’t done so already, please don’t forget to Register Your Bike
to activate your Limited Lifetime Warranty. Protect your purchase by
connecting your Cannondale to your name. Stay up to date with upgrades,
repairs and service announcements.

3
Battery
Charging the battery
Remove/Insert the battery
Pedal Assistance
Drive unit remote
Turning bike on/o
Default display information
Adjusting pedal assist
Assist Modes
Controlling the Lights
Using Walk Assistance
USB Charging
7
10
13
14
15
16
17
18
19
20

4

5
Battery
In this guide are basic battery charging and removal/installation
instructions. See the Battery User Manual that came with your
bike or located in the Cannondale Help Center for complete
battery specifications, operating instructions, and troubleshooting.

6
Charging the battery
For your convenience, the battery on the Cannondale
Adventure Neo Allroad bikes can be charged on or o the bike.
For both methods of charging, start by connecting the battery
charger’s power plug directly into a wall outlet.
DO NOT USE EXTENSION CORD.
The charger’s LED light will illuminate Red to indicate the
charger is receiving power and is ready to charge
1.

7
On-bike charging
On the left side of the bike (side opposite from the gears),
locate the rubber dust-plug and pull it open to obtain access
to the charging port
Insert the charging plug into the port
Charger LED will briefly blink upon connection
a. A steady Red LED indicates the battery is charging
b. LED will turn Green when battery has been fully charged
1.
2.
3.
1

8
O-bike charging
If battery is still installed on the bike, see the following
section: “Removing the battery” for instructions on
how to remove the battery
Place battery on a dry surface away from direct heat
Locate the round rubber dust-seal on the underside
of the battery
Pull open the rubber dust-seal and insert the
charging plug into the port
a. A steady Red LED indicates the battery is
charging
b. LED will turn Green when battery has been
fully charged
For optimal battery life, remove the charger from the
battery port.
Always unplug the battery charger from the wall
outlet after battery charging is complete
DO NOT store the bike plugged into an outlet.
50% charge is recommended for long-term storage
1.
2.
3.
4.

9
1
Removing the battery
Power o battery pack on the handlebar display or by
pressing and holding the power button for three seconds.
Insert the battery key and turn counterclockwise.
Lift and remove the battery from the battery cradle.
After removing battery, always turn the key clockwise until
is stops in order to make sure the locking mechanism is in
the proper position for re-installation of the battery. Failure
to have the mechanism in this position can result in the
battery popping out of the cradle and falling while riding.
1.
2.
3.
4.
The Cannondale Adventure Neo Allroad comes with an easy
to remove semi-integrated battery, which oers the freedom
to charge at home, in the oce, or wherever you have power.
To remove the battery
1
2

10
Installing the battery
Insert key into lock core. Turn key clockwise until it
stops. Remove the key and store it safely.
Place battery into the cradle, bottom first.
With your hand on the top part of the battery pack,
push downward until you hear a click.
Pull upward on the battery to ensure it is locked
into the cradle. If the battery releases when pulled,
reinsert the key and double check that it is turned
clockwise all the way, then push downward on the
battery until you hear a click.
1.
2.
3.
4.
1
2
Click