Canon Super G3 FAX Board-T1 Operating and maintenance manual

Super G3 FAX Board-T1
Installation Procedure
PUB No.F-IM-6467-000 PRINTED IN JAPAN or CHINA
Follow the instructions herein when installing the Super G3 FAX Board-T1
to its host machine. E N G L I S H

2
1.1 Unpacking and Checking the Components
1.1.1 Checking the Contents
In addition to this unit, you will need a fax panel unit (Fax Panel-A1) to enable the iR machine's fax functions.
MEMO:
If the machine is already equipped with an optional Inner 2-Way Tray-E1, you may skip the steps given for the
mounting of the full state sensor unit.
F-1-1
[1] Fax Unit 1 pc. [10] Edge Saddle (black) 1 pc.
[2] Modem PCB 1 pc. [11] Wire Saddle (white) 2 pc.
[3] Full state Sensor Unit 1 pc. [12] Stamp Ink Cartridge 1 pc.
[4] LAN Cover (EUR, AU, KR only) 1 pc. [13] Screw (M3X8) 10 pc.
[5] Telephone Cord 1 pc. [14] Fax Approval Label (EUR only) 1 pc.
Telephone Cord (EUR only) 4 pc. A-TICK Label (AU only) 1 pc.
[6] NCU-PSU Cable 1 pc. [15] Facsimile Guide (US only) 1 pc.
[7] Modem-NCU Cable 1 pc. [16] Facsimile Guide CD-ROM (out side US) 1 pc.
[8] IP-Modem Cable 1 pc. [17] FAX Driver CD-ROM (out side TW) 1 pc.
[9] Modem-NCU Cable 1 pc. FAX Driver CD-ROMt (TW only) 2 pc.
[1] [2] [3] [4]
[6] [7]
[14] [15] [16] [17]
[10][9]
[13]
[11] [12]
[8]
[5]

3
1.2 Installation Procedure
1.2.1 Installation Proce-
dure
1) Turn off the main power switch, and disconnect the
power plug from the power outlet.
2) Remove the machine's rear cover [1].
- 2 screws [2]
F-1-2
3) Remove the machine's rear left cover [1].
- 3 screws [2].
F-1-3
MEMO:
If a LAN cover exits,
1) Remove the LAN cover [1].
- 4 screws [2].
F-1-4
4) Mount the modem PCB [1].
- 1 connector [2].
- 3 screws (M3X8) [3]
F-1-5
[2]
[1]
[2]
[1]
[2]
[2] [1]
[2]
[3]
[1]

4
5) Fit the edge saddle [1] in place.
F-1-6
6) Fit the IP modem cable [1] in place.
- 2 connectors [2]
- 1 edge saddle [3]
F-1-7
7) Mount the fax unit [1].
- 3 screws (M3X8) [2]
F-1-8
8) Fit the modem-NCU FFC [1] in place.
- 2 connectors [2].
9) Connect the modem-NCU cable [3].
- 2 connectors [4]
10) Connect the harness [5] of the speaker.
- 1 connector [6]
F-1-9
11) Mount the LAN cover [1].
- 4 screws (M3X8) [2]
MEMO:
If you have previously removed the LAN cover, use
that cover.
F-1-10
[1]
[1] [2]
[3]
[2]
[1] [2]
[1] [2]
[2] [3]
[4]
[4]
[5][6]
[2]
[1]
[2]

5
When mounting the LAN cover [1], be sure to take
care not to break the grounding plate [3] by the LAN
port [2]. Also, after mounting the cover, check to be
sure that the grounding plate is fully in contact with
the LAN port.
F-1-11
12) Slide out the cassette [1], and open the front cover
[2].
F-1-12
13) Detach the lower cover [1] while shifting it in the
direction of the arrow.
- 5 screws [2]
14) Remove the upper right cover [3].
- 1 screw [4]
F-1-13
15) Turn the developing assembly release lever [1]
clockwise to open the left door [2].
F-1-14
16) Remove the drum unit.
Cover the drum unit with several sheets of copy paper
to protect it from light; then, place it in a safe place.
[1]
[2]
[3]
[1]
[2]
[2]
[2]
[4]
[3]
[1]
[2]
[1]

6
17) Remove the delivery tray [1].
- 2 screws [2]
F-1-15
18) Fit the 2 wire saddles (white) [1] to the machine.
F-1-16
19) Connect the NCU-PSU cable [1] (on the NCU
PCB side).
- 1 connector [2]
- 6 wire saddles [3]
F-1-17
20) Lead the other NCU-PSU cable [2] through the
machine's guide assembly [2].
F-1-18
21) Connect the NCU-PSU cable [1] (on the power
supply side).
- 1 connector [1]
- 1 wire saddle (white) [2]
F-1-19
[2] [1]
[1]
[3]
[2][1]
[1]
[2]
[1] [2]

7
1.2.2 Mounting the Full
State Sensor Unit
If a full state sensor unit already exits, you may skip
the following steps:
1) Remove the front left cover [1] and the delivery
cover [2].
- 2 screws [3]
F-1-20
2) Remove the upper delivery cover [1].
- 1 screw [2]
3) Remove the rear cover [3].
- 1 screw [4]
F-1-21
4) Mount the full state sensor unit [1] to the delivery
assembly [2].
F-1-22
5) Route the harness [1] of the full state sensor unit
through the harness guide [2].
F-1-23
6) Connect the harness of the full state sensor unit to
the connector [1], and arrange the harness as
shown.
F-1-24
[1]
[2]
[3]
[3]
[1] [3] [4][2]
[1]
[1]
[2]
[2]
[1] [2]
[1]

8
1.2.3 After the Work
1) Cut of the area [2] of the rear cover [1] as shown us-
ing nippers.
F-1-25
2) Cut of the area [2] of the machine's rear cover [1] as
shown using nippers.
F-1-26
3) Put back the covers by reversing the steps used to
remove them.
MEMO:
If you have mounted a full sensor unit, put back the
covers identified as 3-1) through 3-3).
3-1) Rear Cover
3-2) Delivery Upper Cover
3-3) Delivery Cover
3-4) Front Left Cover
3-5) Delivery Tray
While mounting the delivery tray, be sure to take care
not to damage the full state sensor lever [1] and the pa-
per retainer [2].
F-1-27
F-1-28
[1]
[2]
[2]
[1]
[2]
[1]
[2]
[1]

9
3-6) Upper Right Cover
3-7) Lower Right Cover
3-8) Machine Rear Left Cover
3-9) Machine Rear Cover
4) Mount the drum unit to the machine.
5) Turn the developing assembly locking lever coun-
terclockwise.
6) Close the left door, cassette, and front cover.
7) Connect one end of the telephone cord to the wall
modular jack and the other end to the iR machine's
modular jack (LINE).
1.2.4 Mounting the Stamp
If the machine is equipped with a DADF, you will have
to fit a stamp ink cartridge.
1) Open the pickup assembly cover and the jam access
cover; then, fit the stamp in place using tweezers.
Make sure that the stamp faces upward.
Be sure to push in the stamp until a click is felt, as the
presence of a gap can cause jams.
F-1-29
2) Close the jam access cover and the pickup assembly
cover.
1.2.5 Attaching the Fax
Approval label (EUR
only)
1) Attach the Fax Approval label [1] firmly by posi-
tioning it against the indicated location of the ma-
chine's rear cover.
F-1-30
1.2.6 Attaching the A-
TICK label (AU only)
1) Attach the A-TICK label [1] firmly by positioning it
against the indicated location of the machine's rear
cover.
F-1-31
[1]
[1]

10
1.3 Checking the Operation
1.3.1 Setting the Type
1) Connect the iR machine's power plug to the power outlet, and turn on its main power switch.
2) In service mode, check to make sure that the type setting is set to the country or the region in which the machine
will be used; i.e.,
2-1) Start service mode as follows:
User Mode key > 2 > 8 > User Mode key
[#SSSW] appears.
2-2) Press [ ] 3 times; when [#CLEAR] appears, press [OK].
2-3) Press [ ] 4 times; when [TYPE] appears, press [OK].
2-4) Press [ ] or [ ] to bring up the desired country or region; then, press [OK].
1.3.2 Basic Settings
The following settings are a minimum set of settings you must make to enable fax communications:
- User Telephone Number
User Mode key > [fax setup] > [basic settings] > [set user telephone number] > user telephone number
- Telephone Line Type
User Mode key > [fax setup] > [basic settings] > [select line type] > select line type
1.3.3 Communications Test
Conduct a communications test to make sure that the fax functions operate normally.
1) Press [fax] and then [on-hook] in sequence to see that a dial tone is heard. If not, check to make sure that the tele-
phone cord is correctly connected to the machine and the wall modular jack.
2) When a dial tone has been heard, type in an appropriate telephone service number (e.g., time service) to make sure
that a connection is made normally. If the attempt fails, check to make sure that the type of the line you selected
in user mode and the type of the actual line match.
3) Type in a telephone number that you can use for communications testing, and send a test original to it to see that
transmission is normal.
4) Have an original sent to the machine to make sure that reception is normal.