Canon imageRUNNER ADVANCE-series User manual

7654321
REVISION 1
Updater V1.0
Service Manual

Application
This manual has been issued by Canon Inc. for qualied persons to learn technical theory,
installation, maintenance, and repair of products. This manual covers all localities where the
products are sold. For this reason, there may be information in this manual that does not
apply to your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements
or changes in products. When changes occur in applicable products or in the contents of this
manual, Canon will release technical information as the need arises. In the event of major
changes in the contents of this manual over a long or short period, Canon will issue a new
edition of this manual.
The following paragraph does not apply to any countries where such provisions are
inconsistent with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks
of the individual companies.
Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may
not be copied, reproduced or translated into another language, in whole or in part, without the
written consent of Canon Inc.
(C) CANON INC. 2009
Caution
Use of this manual should be strictly supervised to avoid disclosure of condential
information.

Explanation of Symbols
The following symbols are used throughout this Service Manual.
Symbols Explanation Symbols Explanation
Check. Remove the claw.
Check visually. Insert the claw.
Check the noise. Use the bundled part.
Disconnect the connector. Push the part.
Connect the connector. Plug the power cable.
Remove the cable/wire
from the cable guide or wire
saddle.
Turn on the power.
Set the cable/wire to the
cable guide or wire saddle.
Remove the screw.
Tighten the screw.
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specic functions and the
relationship between electrical and mechanical systems with reference to the timing of
operation.
In the diagrams, represents the path of mechanical drive; where a signal name
accompanies the symbol, the arrow indicates the direction of the electric
signal.
The expression "turn on the power" means ipping on the power switch, closing the
front door, and closing the delivery unit door, which results in supplying the machine with
power.
2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is
"High", while '0' is used to indicate "Low". (The voltage value, however, differs from
circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked
in the eld. Therefore, the operations of the microprocessors used in the machines
are not discussed: they are explained in terms of from sensors to the input of the DC
controller PCB and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product
improvement or other purposes, and major changes will be communicated in the form of
Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service
Manual and all relevant Service Information bulletins and be able to identify and isolate faults
in the machine.

Regarding Product Names used in this service manual
In this service manual, the following product names are used.
Content Delivery System
It is abbreviated to CDS in this service manual.
Universal Gateway
It is abbreviated to UGW in this service manual.
Service Management Service
It is abbreviated to SMS in this service manual.
Embedded RDS
It is abbreviated to eRDS in this service manual.
License Management System
It is abbreviated to LMS in this service manual.
Abbreviation of Service Support Tool
It is abbreviated to SST in this service manual.
•
•
•
•
•
•

Contents
1Functional Overview
Overview ------------------------------------------------------------------------1-2
Installing Firmware ---------------------------------------------------------------- 1-2
Installing MEAP Application/System Option--------------------------------- 1-3
System Conguration --------------------------------------------------------1-4
List of Functions ---------------------------------------------------------------1-4
Distribution Flow---------------------------------------------------------------1-5
Firmware Installation Flow------------------------------------------------------- 1-5
MEAP Application/System Option Installation Flow----------------------- 1-5
Limitations and Cautions ----------------------------------------------------1-6
Limitations --------------------------------------------------------------------------- 1-6
Cautions------------------------------------------------------------------------------ 1-6
2Preparation
Overview of Preparation-----------------------------------------------------2-2
Setting Sales Company’s HQ ----------------------------------------------2-2
Network Settings --------------------------------------------------------------2-3
Connecting to External Network ----------------------------------------------- 2-3
Conrming URL Setting of Distribution Server ----------------------------- 2-3
Communication Test -------------------------------------------------------------- 2-5
Enabling UGW Link-----------------------------------------------------------2-6
Enabling [Update Firmware] Button of User Mode -------------------2-7
Enabling [Install Application/Options] Button of User Mode--------2-7
Enabling [Manual Update] Button of User Mode (Remote UI)-----2-8
3Operations
Firmware Operations---------------------------------------------------------3-2
Downloading and Updating Firmware ---------------------------------------- 3-2
a. UGW-linked Download and Update (Full-remote Update)-------------------- 3-2
b. UGW-linked Download (Remote Distribution Update) ------------------------- 3-3
c. Manual Download and Update (On-site Update from Service Mode)------ 3-5
Deleting Firmware Distribution Schedule ----------------------------------- 3-11
Updating Downloaded Firmware (Applying Firmware) ------------------3-12
Deleting Downloaded Firmware-----------------------------------------------3-13
System Management Operations --------------------------------------- 3-14
Various Setting --------------------------------------------------------------------3-14
Setting URL of Distribution Server ----------------------------------------------------3-14
Setting Log Level --------------------------------------------------------------------------3-15
Displaying Logs -------------------------------------------------------------------3-16
Update Logs --------------------------------------------------------------------------------3-16
System Logs --------------------------------------------------------------------------------3-17
Communication Test -------------------------------------------------------------3-19
4Maintenance
Upgrading Updater -----------------------------------------------------------4-2
Formatting Hard Disk --------------------------------------------------------4-2
How to Replace Controller Boards ---------------------------------------4-3
How to Replace Devices ----------------------------------------------------4-3
5FAQ
FAQ on Installing Firmware-------------------------------------------------5-2
FAQ on Installing MEAP Application/System Option-----------------5-3
FAQ on General Matters of Updater -------------------------------------5-4
6Troubleshooting
Troubleshooting on Firmware Installation-------------------------------6-2
Information required for Reports ------------------------------------------6-3
Information required for Service Technicians to Obtain on Site-------- 6-3
Information to Report ------------------------------------------------------------- 6-3
Debug Logs---------------------------------------------------------------------6-4
Obtaining Log Files---------------------------------------------------------------- 6-4
7Error Messages
Error Messages----------------------------------------------------------------7-2
Error Codes---------------------------------------------------------------------7-6
How to read an error code------------------------------------------------------- 7-6
Error Code --------------------------------------------------------------------------- 7-6

Appendix
Conrming the version of Updater ------------------------------------ App-II
Glossary --------------------------------------------------------------------- App-II

1
1Functional Overview
Functional Overview
Overview
System Conguration
List of Functions
Distribution Flow
Limitations and Cautions
■
■
■
■
■

1
1
1-2
1-2
Functional Overview > Overview > Installing Firmware
Functional Overview > Overview > Installing Firmware
Overview
Updater provides functions that enable network communication with Content Delivery System
V1.0 (hereinafter CDS) to install rmware, MEAP applications and system options.
Firmware Installation
Updater function enables users to distribute rmware through CDS via Internet. Particularly
on e-Maintenance/UGW (called NETEYE in Japan)-enabled devices, rmware can be
updated remotely, which effectively slashes costs incurred in eld services.
MEAP Application/System Option Installation
By linking devices to CDS and License Management System (providing the function to
manage licenses; hereinafter LMS), applications can be installed in devices via Updater,
regardless of those not embedded (MEAP application) or embedded (system options) in
devices.
Installing Firmware
With link to Updater, service technicians provide rmware install services in the following 3
methods.
Distribution Method
Download
Commanded
by:
Update
Timing
Downloadable Firmware Versions
Previous
Ver
Current
Ver
Newer
Ver
a. UGW-linked Download / Update
(Full-remote update)
UGW Auto No Yes Yes*1
b. UGW-linked Download
(Remote Distribution / Update)
UGW Manual Yes Yes Yes
c. Manual Download / Update
(On-site Update via Service mode)
Local UI Auto No Yes Yes*1
Manual Yes Yes Yes
*1:You can select the version allowed Remote Update.
•
•
T-1-1T-1-1
a. UGW-linked Download and Update (Full-Remote Update)
If the device is linked to UGW and the distribution schedule and update setting
are registered on UGW in advance, full remote rmware update is available on an
imageRUNNER ADVANCE-series device. Upon downloaded from CDS, the rmware is
updated on the device.
UGW 1) Set up customers,
device types, distribution
schedule and the
command for download
3) Give a firmware distribution
command to e-ROS.
Firmware Upload
4) Download
firmware
5) Writing process is
automatically started upon
download completed.
2) Notify distribution
information to CDS.
Canon Inc.
CDS
Firmware
UGW Operator
Sales Company
/ Partner
imageRUNNER
ADVANCE
e-RDS
Updater
b. UGW-linked Download (Remote Distribution / Update)
If the device is linked to UGW and the distribution schedule is registered on UGW in
advance, rmware can be distributed to an imageRUNNER ADVANCE-series device before
a service technician actually visits the customer site. This allows the service technician to
update the rmware manually immediately after completing device inspection.
UGW 1) Set up customers,
device types, distribution
schedule and the
command for download
3) Give a firmware distribution
command to e-ROS.
Firmware Upload
4) Download
firmware
5) Writing process is started by
manually executing Updater.
2) Notify distribution
information to CDS.
Canon Inc.
CDS
Firmware
UGW Operator
Sales Company
/ Partner
imageRUNNER
ADVANCE
e-RDS
Updater
Service
Technician
F-1-1F-1-1
F-1-2F-1-2

1
1
1-3
1-3
Functional Overview > Overview > Installing MEAP Application/System Option
Functional Overview > Overview > Installing MEAP Application/System Option
c. Manual Download and Update (On-site Update via Service Mode)
If an imageRUNNER ADVANCE-series device has connection with the external network,
a service technician can gain access to CDS via Service mode to download and update
rmware. This allows service technicians to update the rmware as needed on the
customer site even without PCs.
Firmware Upload
1) Manually execute
Updater.
2) Firmware distribution
Canon Inc.
CDS
Firmware
imageRUNNER
ADVANCE
Updater
Service
Technician
NOTE:
“External network” here means the network connecting the device to CDS via Internet.
NOTE:
Users are able to gain rmware distribution in the following 3 methods by introducing
CDS. See User Manual for detailed information.
Distribution Method
Download
Commanded
by
Update
Timing
Downloadable Firmware Versions
Previous Ver Current Ver Newer Ver
Manual download/
update via Local UI Local UI Auto No No Yes *1
Manual No No Yes *1
Manual download/
upload via Remote UI Remote UI Auto No No Yes *1
Manual No No Yes *1
Special download/
upload via Remote UI Remote UI - Specic version only (Obtain it separately)
*1: Only the latest version of Remote update-enabled version is downloadable.
Installing MEAP Application/System Option
The following is the installation method of MEAP application/system option which is enabled
by applying CDS.
a. LMS-linked MEAP Application/System Option Installation
If an imageRUNNER ADVANCE-series device is connected to the external network, user or
service technician can gain access to CDS from User mode to install a MEAP application
or a system option.
F-1-3F-1-3
Installing MEAP Application
CDS
Application
LAN
LAN
imageRUNNER
ADVANCE
1) Enter LAN
4) Transmit MEAP
Application/LF
If a customer enters LAN
purchased from the sales company
to an imageRUNNERADVANCE-
series device, MEAP application/LF
can be installed.
LAN: License Access Number
LF: License File
(DSN: Device Serial Number,
automatically sent to CDS upon LAN
entered.)
5) Manuals, etc.
LMS
LAN
MEAP
Application
3) Create LF
2) License
Authentication
Canon Inc.
Sales
Company
Manual
Upload
User
Installing System Option
CDS
Application
User
LAN
LAN
imageRUNNER
ADVANCE
1) Enter LAN
4) Transmit LF
If a customer enters LAN
purchased from the sales company
to an imageRUNNERADVANCE-
series device, a LF can be installed.
LAN: License Access Number
LF: License File
(DSN: Device Serial Number,
automatically sent to CDS upon LAN
entered.)
5) Manuals, etc.
LMS
LAN
3) Create LF
2) License
Authentication
Canon Inc.
Sales
Company
Manual
Upload
F-1-4F-1-4
F-1-5F-1-5

1
1
1-4
1-4
Functional Overview > List of Functions
Functional Overview > List of Functions
System Conguration
The gure below schematically shows the system conguration.
Internet
CDS
CDS
CDS
CDS
MEAP application
Manual
LMS
LMS
LMS
LMS
User
UGW
UGW
UGW
UGW
Firmware
Application/License
Sales
Company
Business
Group
QA
Service
Technician
License
Access No.
Updater
eRDS
Dealer
Canon Inc.
Manual
Readme
Command for Firmware Distribution
Application
Firmware
F-1-6F-1-6
List of Functions
The matrix below shows the list of functions provided by Updater.
Category Function Service
Mode
User
Mode
Remote
UI
UGW-
linked
Firmware
Checking rmware compatibility Yes - - -
Checking special rmware Yes - - -
Checking latest rmware
version - Yes Yes -
Registering/deleting rmware
distribution schedule Yes Yes Yes -
Conrming and downloading
rmware Yes Yes Yes Yes
Updating downloaded rmware Yes Yes Yes -
Cancelling downloaded
rmware Yes Yes Yes -
Acquiring rmware distribution
information registered from
UGW
- - - Yes
Notifying rmware version
information - - - Yes
MEAP application/
system option
Inquiring license for MEAP
application/system option - Yes Yes -
Installing MEAP application /
system option - Yes Yes -
System
Management
Settings Yes - - -
Testing communications Yes Yes Yes -
Displaying update logs Yes Yes Yes -
Displaying system logs Yes Yes Yes -
Internal system
error notication
Notifying internal system error
occurrence to distribution server Yes Yes Yes Yes
T-1-2T-1-2

1
1
1-5
1-5
Functional Overview > Distribution Flow > MEAP Application/System Option Installation Flow
Functional Overview > Distribution Flow > MEAP Application/System Option Installation Flow
Distribution Flow
Firmware Installation Flow
Service technicians provide rmware install services in the following 3 methods.
a: UGW-linked download and update
b: UGW-linked download
c: Manual download and update
: Operator of each company : User operation
Firmware
Market Release
UGW setting
for distribution
(UGW-linked)*1
Automatic download
Distribution setting &
Download
Via Service mode
(Local UI)
Automatic update
Apply (Update)
Via Service mode
(Local UI)
Distribution setting &
Download
Via User mode
(Local UI)
Distribution setting &
Download
Via User mode
(Remote UI)
Apply (Update)
Via User mode
(Local UI)
Apply (Update)
Via User mode
(Remote UI)
b
c
a
Download via SST
Update via SST
Firmware acquisition
*1: Schedules for UGW-linked distribution are maintained on CDS.
F-1-7F-1-7
MEAP Application/System Option Installation Flow
MEAP application/system option installation method using service mode is not provided.
Be sure to use the user mode to install.
: Operator of each company : User operation
License Access
Number Acquisition
(packaged with the
product)
Device Serial No.
Acquisition
(from the device)
Application
Market Release
License File
Acquisition
(from LMS)
License Key
Acquisition
(from LMS)
Install
Via User mode
(Local UI)
Install distributed
application
Via User mode
(Remote UI)
System Option
Install
Via User mode
(Local UI)
MEAP Application
Manual Install
Via User mode
(Remote UI)
System Option
Manual Install
Via User mode
(Remote UI)
F-1-8F-1-8

1
1
1-6
1-6
Functional Overview > Limitations and Cautions > Cautions
Functional Overview > Limitations and Cautions > Cautions
Limitations and Cautions
Limitations
Changing Date/Time on Device
When a user changes the date/time setting on the device (including change of the setting
according to daylight saving time), the rmware distribution may not be performed as
scheduled.
But there is not the problem if it is time adjustment of several minutes with NTP servers.
Change of Setting from Service mode
Any settings from Service mode will be enabled after restarting the device.
Cautions
Concurrent use of Updater functions
Multiple users cannot use Updater functions on a device concurrently by using it together with
Remote UI.
Coexistence of Remote UI and other tools
Users logged in SMS (Service Management Service) are unable to use Update functions
from Remote UI.
Using Updater function from Remote UI
Upon the following operations done, Updater functions are suspended from Remote UI for
certain duration.
When a user exits Web browser without clicking [Portal] or [Log Out] button in the setting of
Remote Login Service via SMS
When a user exits Web browser without clicking [Portal] button in the setting of not to use
Remote Login Service via SMS.
When a user exits Web browser without clicking [Log out from SMS] or [To Remote UI]
button.
Wait for EOJ (end of job) Function
Firmware update will be triggered only after the following jobs are completed.
This is the Updater-specic specication.
•
•
•
Job/Function
type
Receiving Printing Queued print
jobs
Sending Queued send
jobs
COPY -Wait for EOJ *1 Wait for EOJ *1 - -
PRINT Wait for EOJ
(end of job)*1
Wait for EOJ *1 Wait for EOJ *1 - -
FAX Wait for EOJ *1 Wait for EOJ *1 Wait for EOJ *1 Wait for EOJ *1 Wait for EOJ *1
I-FAX Receipt Cancel
processing to
trigger update
*1
Wait for EOJ *1 Wait for EOJ *1 - -
SCAN *2 -Wait for EOJ *1 ---
Report Print -Wait for EOJ *1 Wait for EOJ *1 - -
*1: Soon after receipt, Print and FAX jobs are not recognized as jobs.
*2 SCAN jobs are recognized as EOJ upon scanning completed.
Even during transfer, Pull SCAN job processing is cancelled soon after scanning is
completed.
Firmware update is cancelled if the jobs are not completed within 10 minutes. If this occurs,
the error code, 8x001106, will be returned (different numbers will be shown for x depending
on the execution modes).
Firmware update is executed if the jobs stated above are not in the queue.
Follow the shutdown sequence to reboot the device after the rmware is updated.
The following rmware versions do not support Wait for EOJ Function.
iR-ADV V5000 series: V40.17 or earlier
iR-ADV V7000/9000 series: V40.18 or earlier
For the versions above, triggering rmware update will cancel all COPY/PDL jobs
submitted and/or queued. Only jobs with power-off safeguard (Fax/ I-Fax/ Auto-Report
Print) are recovered after reboot.
•
•
T-1-3T-1-3

2
2Preparation
Preparation
Overview of Preparation
Setting Sales Company’s HQ
Network Settings
Enabling UGW Link
Enabling [Update Firmware] Button of User Mode
Enabling [Install Application/Options] Button of User
Mode
Enabling [Manual Update] Button of User Mode (Remote
UI)
■
■
■
■
■
■
■

2
2
2-2
2-2
Preparation > Setting Sales Company’s HQ
Preparation > Setting Sales Company’s HQ
Overview of Preparation
The following should be prepared before using Updater.
For updating of rmware
Installation
Method
Setting
Sales
Company’s
HQ
Network
Settings
Enabling
UGW Link
Enabling [Update
Firmware] Button
of User Mode
Enabling [Manual
Update] Button
of User Mode
(Remote UI)
UGW-linked
Download and
Update
Yes Yes Yes - -
UGW-linked
Download Yes Yes Yes - -
Manual Download
and Update Yes Yes - - -
Manual Download
and Update via
Local UI
Yes Yes - Yes -
Manual Download
and Update via
Remote UI
Yes Yes - Yes -
Special Download
and Update via
Remote UI
Yes - - - Yes
For Install of Application
Installation Method Network SettingsEnabling [Install Application/
Options] Button of User Mode
LMS-linked Installation Yes -
LMA-linked installation via Local UI Yes Yes
LMS-linked installation via Remote UI Yes Yes
•
•
T-2-1T-2-1
T-2-2T-2-2
Setting Sales Company’s HQ
When using devices input in the markets listed below, the default setting of Sales Company’s
HQ should be changed before obtaining rmware distributed from CDS. Unless the setting is
changed properly, the desired rmware may not be able to be selected.
Market Default Setting of Sales
Company's HQ
Setting of Sales Company's
HQ after Change
Canada US CA
Latin America US/SG LA
Hong Kong SG HK
Go to the following screen to change the setting of Sales Company's HQ.
Service
Technician
Setting of Device Service Mode
(Level 1)
COPIER > FUNCTION > INSTALL > CDS-CTL
NOTE:
The list below shows the setting of Sales Company’s HQ for CDS-CTS by market.
Check and adhere to the appropriate setting for your market.
<List of Sales Company’s HQ and the settings for CDS-CTL>
Japan = JP China = CN
USA = US Hong Kong = HK
Singapore = SG Australia = AU
Europe = NL Canada = CA
Korea = KR Latin America= LA
T-2-3T-2-3

2
2
2-3
2-3
Preparation > Network Settings > Conrming URL Setting of Distribution Server
Preparation > Network Settings > Conrming URL Setting of Distribution Server
Network Settings
Connecting to External Network
The method of connecting to external network is similar to a normal network connection
method. Refer to user manual of the device for details.
NOTE:
See User Manual for how to connect the device to the external network.
Before using UGW link or User mode, see the sections below to prepare as required.
“Enabling UGW Link”
“Enabling [Update Firmware] Button of User Mode”
“Enabling [Install Application/Options] Button of User Mode”
•
•
NOTE:
“External Network” here means the network connecting the device to CDS via Internet.
Conrming URL Setting of Distribution Server
This section describes how to conrm the URL setting of the distribution server.
1. Start [Service Mode] at Level 1.
1). Press [Setting/Registration (User Mode)] button on the control panel.
2). Press [2] and [8] buttons at a time on the control panel.
3). Press [Setting/Registration (User Mode)] button on the control panel.
4). [Service Mode] screen is shown.
2. Press [Updater] button.
F-2-1F-2-1

2
2
2-4
2-4
Preparation > Network Settings > Conrming URL Setting of Distribution Server
Preparation > Network Settings > Conrming URL Setting of Distribution Server
3. Press [Software Management Settings] button.
4. Press [Settings] button.
F-2-2F-2-2
F-2-3F-2-3
5. Ensure to enter “https://device.c-cdsknn.net/cds_soap/updaterif” in the eld beside the
[Delivery Server URL] button.
If the URL is not entered or a wrong URL is entered in the eld, click [Delivery Server URL]
button to show the virtual keypad. Check the URL and enter the correct one.
6. Press [OK] to set the entered items. Now the URL of the distribution server is successfully
set.
F-2-4F-2-4

2
2
2-5
2-5
Preparation > Network Settings > Communication Test
Preparation > Network Settings > Communication Test
Communication Test
This section describes how to check if the communication is normally done to the distribution
server and/or the le server.
1. Start [Service Mode] at Level 1.
1). Press [Setting/Registration (User Mode)] button on the control panel.
2). Press [2] and [8] buttons at a time on the control panel.
3). Press [Setting/Registration (User Mode)] button on the control panel.
4). [Service Mode] screen is shown.
2. Press [Updater] button.
F-2-5F-2-5
3. Press [Software Management Settings] button.
4. Press [Test Communication] button.
F-2-6F-2-6
F-2-7F-2-7

2
2
2-6
2-6
Preparation > Enabling UGW Link
Preparation > Enabling UGW Link
5. Press [Yes] button.
Obtain the download le information for communication test from the distribution server
(to execute the communication test to the distribution server).
Using the download le information for communication test, the contents for test are
downloaded from the le server (for the communication test to the le server).
6. Upon the communication test completed, the communication test result screen is shown.
Press [OK] button to exit this operation.
F-2-8F-2-8
F-2-9F-2-9
Enabling UGW Link
When installing the rmware in the method of “UGW-linked Download and Update” or “UGW-
linked Download”, the following should be set before actually using UGW link.
Service Technician
Setting of Device
Service Mode
(Level 1)
COPIER >OPTION >FNC-SW >CDS-UGW
(0 -> 1)
Setting of UGW
WebPortal
In [Customer Management] screen, set [Do not
distribute rmware] to [Distribute rmware].
Sales Company's HQ Setting of Authorities on
UGW WebPortal
See "Analysis>Firmware Distribution
Information" to grant the appropriate authorities
to each account.
NOTE:
See “imageWARE Remote Operator’s Manual / e-Maintenance Business Operation
Manual“ for how to operate UGW WebPortal.
[Distribute Firmware] should be set on [Customer Management] screen for staff in charge
of setting for [Enter customer information] or [Command for rmware distribution] in order
to allow them to select the desired device on [Firmware Distribution Information] screen.
If [Distribute Firmware] is not shown on [Customer Management] screen of UGW
WebPortal, appropriate authorities may not be set to each account in Firmware
Distribution Information. Contact the Sales Company HQ concerned for conrmation.
•
•
•

2
2
2-7
2-7
Preparation > Enabling [Install Application/Options] Button of User Mode
Preparation > Enabling [Install Application/Options] Button of User Mode
Enabling [Update Firmware] Button of User Mode
To allow users to install rmware using Updater, the setting of rmware installation should be
set to ON for users in advance.
Service
Technician
Setting of Device Service Mode
(Level 1)
COPIER >OPTION >FNC-SW >CDS-FIRM
(0 -> 1)
User Mode screen for Updater when the setting is not enabled (CDS-FIRM(0)):
User Mode screen for Updater when the setting is enabled (CDS-FIRM(1)):
•
•
F-2-10F-2-10
F-2-11F-2-11
Enabling [Install Application/Options] Button of User
Mode
To allow users to install applications using Updater, the setting of application installation
should be set to ON for users in advance.
Service
Technician
Setting of Device Service Mode
(Level 1)
COPIER >OPTION >FNC-SW >CDS-MEAP
(0 -> 1)
User Mode screen of Updater when the setting is not enabled (CDS-MEAP(0)):
User Mode screen of Updater when the setting is enabled (CDS-MEAP(1)):
•
•
F-2-12F-2-12
F-2-13F-2-13

2
2
2-8
2-8
Preparation > Enabling [Manual Update] Button of User Mode (Remote UI)
Preparation > Enabling [Manual Update] Button of User Mode (Remote UI)
Enabling [Manual Update] Button of User Mode
(Remote UI)
To allow users to install rmware from Updater using the le on Local PCs, the setting of
rmware installation should be set to ON for users in advance.
Service
Technician
Setting of Device Service Mode
(Level 1)
COPIER >OPTION >FNC-SW >LOCLFIRM
(0 -> 1)
Remote UI screen of Updater when the setting is not enabled (LOCLFIRM (0)):
Remote UI screen of Updater when the setting is enabled (LOCLFIRM (1)):
•
•
F-2-14F-2-14
F-2-15F-2-15