Canon Creative Park Paper Aquarium Clown Fish User manual

Front
A 1
Back
1) Cut out A1-A5 and
assemble each part.
As for A1, fold each side inwardly
and glue the back of each side together.
Make four of these.
As for A2-A5, fold the upper side inwardly
and glue the back of each side together.
As for A7, cut along the cut line and fold it
in half after cutting out the designated area.
Then attach the sides together.
Front
Back
Make two each.
2) Assemble A1-A5.
A 1A 1A 1A 1
A 2A 2A 4A 4
A 3A 3A 5A 5
As shown in the diagram, assemble by attaching
both ends of A1 to the glue tabs of A2-A5.
So that it becomes box-shaped, do
the same for the ends of A1 and A4/A5.
Add some glue to the glue tabs and
attach A7 to the upper part of the frame.
Attach A6 to the bottom
with the sand part face up.
Fold A6 and A8 in half and attach the back
of each side together respectively.
*A8 is the lid (upper portion) of the frame.
When everything is complete, put it on the top.
A 5
A 4
A 1
A 5
A 3
Attach A5 to the remaining
A3 glue tabs.
Likewise, attach A4 to A2.
3) Cut out A6-A8 and assemble each part.
A 6
A 8
A 7
A 7
4) Assemble A6 and A7 to the frame
you've already completed.
A 6
Frame
Paper Aquarium : Clown fish [AssemblyInstructions]
You will need
Explanation of symbols
Scissors,glue, ruler, a used ball-point pen, white string
Valley fold (Dashed and dotted line)
Cut line (Solid line)
Mountain fold (Dotted line)
Glue tab
Cut in line (Red solid line)
Cut out
Assembly tip
Trace along the folds with a ruler and a used
pen (no ink) to get a sharper, easier fold.
Caution: This craft requires the use of glue, scissors, and other tools
which may be dangerous to young children. Please keep them out of
reach of children while you work.

Option 1
Option 2
Clown fish Finish
1) Cut out B1-B4 and
assemble each part.
Fold B1-B3 in half, attach the back of
each respective side together,
and cut each piece out.
Fold C1 and C2 in half,
attach the back of each respective
side together, and cut
each piece out.
A space will be created on the
top of C3.
Attach C1 and C2
by putting
the triangular
glue tabs
together.
Insert it into the space on
top of C3
and attach it
on the inside.
As for B4, start assembly by attaching
from the sides. As a final step, put the
remaining piece on the top like a lid.
B 2
B 4
2) Attach B1-B4.
3) Attach D1-D6.
B 4
B 1
B 3B 2
D 1
D 1
D 3
D 3 D 5
D 4
D 2
D 2
1) Cut out C1-C3 and
assemble each part.
C 2
C 3
2) Attach C1-C3.
C 1
C 2
C 3
1) Cut out D1 and D2,
make incisions, and curve them
as indicated by the arrows.
*Do not curve the fin part.
2) Cut out D3-D7 and assemble
each part.
D 6
D 6
D 7
Fold D3-D5 in half and
attach the back of each side
together respectively.
Make a fold on D6.
Fold D7 in half,
attach the back of
each side together,
and make incisions.
*Do not attach this part.
Place D6 between D1 and D2
and attach the back of each
respective side together.
Insert D3 and attach
the glue tabs together.
Cut the string into
an approximately
10cm piece.
Insert D4 and D5 in the hole,
pull out the head to hide
the front part of the hole,
and stabilize it with the glue tab.
4) Attach the string and D7 on the clown fish.
Put one end of the string
between the fin and attach
the sides together to secure it.
As for the other end
of the string, put it in
D7's incision.
Wrap it several times
around D7 so that
it doesn't come off.
D 7
*Do the same for the other fish.
1) Wrap the clown fish's string
around D7 as many times
as you wish to obtain
your desired length.
2) Hook the clown fish
on the hole found in the upper
part of the frame.
3) Arrange Option 1 and
Option 2, put the lid (frame A8)
on top, and you're done!
Frame A8
Option 1
Option 2
Paper Aquarium : Clown fish [AssemblyInstructions]