Canvas 068-7826-4 User manual

MODEL NO. 068-7826-4
ASSEMBLY INSTRUCTIONS
Toll-free 1-888-670-6684
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
ANDERSON CABINET

2
IMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS
Warning! To reduce the risk of serious injury, read the following safety
instructions before assembling and using the dining table.
• This product is intended for domestic indoor use only.
• The product should be placed on a flat horizontal surface.
• Arrange necessary manpower when assembling or moving the product.
• Do not push furniture, especially on a carpeted floor. Have someone help you lift heavy items and set it
in place.
• Check all screws periodically for tightness. When required, tighten them again.
Important Safety Instructions 2
Parts List 3-6
Assembly 7-25
Warranty 26
Needed for Assembly
MODEL NO. 068-7826-4
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size

3
PARTS LIST
A
Right End - 1
Left End - 1
B
Top Molding - 1
C
Top - 1
D
Small Shelf - 1
E
Shelf - 1
F
Large Shelf - 1
G
Brace - 1
H
Right Front/Left Rear Foot - 2
J
Bottom - 1
I

4MODEL NO. 068-7826-4
K
Left Front/Right Rear Foot - 2
Bottom Brace - 2
L
Left Drawer Side - 2
M
Drawer Back - 2
N
Right Drawer Side - 2
O
Drawer Bottom - 2
P
Drawer Brace - 2
Q
Back - 1
S
PARTS LIST
Drawer Front - 2
R

5
PARTS LIST
Large Hidden Cam- 36
3
Small Hidden Cam - 12
4
Long Wood Dowel - 30
7
Short Wood Dowel - 4
8
Cover Card - 1
9
Knob - 2
10
Long File Glide - 2
11
Short File Glide - 4
12
Angled Head Cam Screw - 36
5
Angled head
Straight Head Cam Screw - 12
6
Straight head
Extension Rail - 4
1
Extension Slide - 4
2
Extension Set
shown separated

6MODEL NO. 068-7826-4
Front File Glide - 2
13
Black 2-9/16" Bolt - 8
18
Black 1-1/8" Flat Head Screw - 3
20
Black 1-1/2" Flat Head Screw - 12
19
Black 7/8" Machine Screw - 2
21
Black 1/2" Pan Head Screw - 32
22
Furniture Tipping Restraint Kit - 1
99
Flat Washer - 8
15
File Hanger - 4
14
Ballast - 2
16
Nail - 50
17
PARTS LIST

7
ASSEMBLY
D
E
Step 1
Requires C, D, E, 7, 20
Fasten the TOP MOLDING (C) to the TOP (D). Use three BLACK 1-1/8" FLAT HEAD
SCREWS (20).
Insert eight LONG WOOD DOWELS (7) into the exact holes shown in the short edges of
the TOP (D) and SMALL SHELF (E).
Rounded edge
Rounded edge
7
7
7
7
C
7
20
ASSEMBLY
20

8
ASSEMBLY
MODEL NO. 068-7826-4
G
F
Step 2
Requires F, G, 7
Insert eight LONG WOOD DOWELS (7) into the into the exact holes shown in the short
edges of the SHELVES (F and G).
7
7
7
7
Rounded edge
Rounded edge
7

9
ASSEMBLY
Step 3
Requires I, 5, 7
Turn eight ANGLED CAM SCREWS (5) into the small holes in the BOTTOM (I).
Insert four LONG WOOD DOWELS (7) into the edges of the BOTTOM (I).
I
Angled head
7
7
Angled head
5 7
Finished
Edge
5

10
ASSEMBLY
MODEL NO. 086-7826-4
Step 4
Requires J, K, L, 3, 5, 7
Turn two ANGLED HEAD CAM SCREWS (5) into the FEET (J and K).
Insert two LONG WOOD DOWELS (7) into the FEET (J and K) and one into the long
edge of the BOTTOM BRACE (L).
Insert two LARGE HIDDEN CAMS (3) into the holes in the BOTTOM BRACE (L) as shown.
Fasten the FEET (J and K) to the BOTTOM BRACE (L). Tighten two LARGE HIDDEN CAMS.
Repeat this step for the other FEET (J and K) and BOTTOM BRACE (L).
321
The arrow must
point toward the
edge of the board.
3
Angled head
5 73
7
77
5
5
3
J
K
L
Angled head