Capetti Elettronica MWDG-GSM User manual

V3.0
Technical Assistance:
eMail ufficiot[email protected]
Phone [phone]
Mobile [phone]
Quick Guide
MWDG-GSM
Whatsapp
Telegram
Capetti Uff. Tecnico
Contatto Telegram

V3.0
System Components
Notes
2
LED
Indicators
12/24V
GSM Antenna
WSN Antenna
ANT-EXT
SIM Card
USB Cable
WineCapManager
HHDR1524 Power supply

V3.0
Service Center Connection
1. Insert a working SIM and configure the provider APN
and related PIN using WineCapManager.
2. GSM LED (green):
a. 1 flash/sec: network searching
b. 1 flash/4sec: signal ok
3. Connection test: issue to basestation command 4using
WinecapKey. CCS Status LED turns on (green), at the
end of the upload process, LED turns off
4. To verify on Service Center website: www.winecap.it
(valid account needed)
Terminal Blocks
J3
Vin + Serial
J10
Battery Backup
1
NC
1
BATT_12V
2
MB A+
2
GND
3
MB B-
4
GND
5
P.E.
6
GND
7
12/24Vdc
10
3
1
1
1
1
J3
J10
Approach WinecapKey in
this point, wait for 4 amber
flashes of the System LED
then remove

V3.0
Led Description
System
System indicator:
•slow flash = OK
•rapid flash = probe/datalogger enrolling
Logger
Memory status
CCS
Service Center connection:
•switched on (green) = connection in progress
•switched on (red) = connection error
•flashing = GSM signal test
GSM
GSM communication:
•rapid flash (green) = looking for signal
•flashing (green - 1 flash/4sec) = GSM network OK
•flashing (red/green) = GSM error
WSN
Wireless Sensor Network
•green = measure reception
•red = transmission in progress
WineCapManager
1. Launch Setup.exe from the WineCapManager folder ed
run the installation.
2. Launch WineCapManager and select “Local Connection”.
3. Wait for MWDG device detection.
4. Create a new database, insert a referring name, and click
on “open”.
5. Insert licence file located in the CD (menu
Basestation/Insert licence)
6. Wait for the automatic alignment of the list and the status
of sensors from MWDG to PC.
4
9

V3.0
USB Driver
1. Connect USB cable to PC.
2. Access to Control Panel/Device Manager then click
on MWDG device.
3. Manually install the USB driver (MWDG_CDC.inf)
available on CD.
4. Click “continue” when requested
5. Note for WINDOWS 8.1: in case of troubles follow
the “Win8.x Installare Drivers USB R01.pdf” manual
available on CD.
At the end of the installation process, a new COM port
will be installed: “WineCap MWDG (CDC)”
Start Sensors
1. Connect MWDG as shown before, power up and
verify Led “System” flashing
2. Activate the probe/datalogger:
a. approach WinecapKey
b. wait for 2 flashes (test)
c. remove WinecapKey
3. Verify LED:
Flash count - Wireless mode
Status/Radio signal
quality
5 green flashes
Excellent
4 green flashes
Good
3 green flashes
Fair
2 amber flashes
Sufficient
1 red flash
Insufficient
1 red flash 2” long
OUT OF RANGE
Network searching
2 red flashes 2” long
STANDBY
Short-long-short red
flashes series
FACTORY RESET
Device not enrolled
8
5

V3.0
How to Install
Guidelines to follow during the system installation
process
1. Position to the selected location and power on the
MWDG
a. select, if possible, a central position among to the
wireless plant
b. avoid metal obstructions and reinforced concrete
structures
c. verify the GSM signal
WSN and GSM antennas distance
must be >50cm
2. Move the probe/datalogger to the
measure location
a. verify received signal
important: small movement can improve the
radio signal quality
b. outdoor probes must be placed upward and north
oriented to avoid tampering
3. Adding repeaters to improve radio coverage
a. couple a repeater to the systema and write down
assigned address
b. position it upward among obstacles and people
c. select a “strategic” point among the plant
4. Using the WD04T tester probe
a. couple the probe to the system
b. activated the test, the probe displays the percentage
of the radio signal level
c. Declares the radio reference in a specific point: router
address or zero for MWDG
Manual: Refer to “WINECAP User Manual.pdf” located on
CD for further instructions regarding the network and the
installation process.
6
7