Capetti Elettronica WSD10TII User manual

WSD10TII
User Manual

WSD10TII
User Manual
PAGE 2/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
1. Disclaimer.
•Specifications are subject to change without notice and should not be interpreted as any commitment on the part of Capetti Elettronica
S.r.l.
•Capetti Elettronica S.r.l. assumes no responsibility for any errors that may appear in this document. In no case Capetti Elettronica S.r.l.
will be liable for incidental or consequential damages resulting from the use of this document or the systems described in this
document.
•All Contents published or distributed by Capetti Elettronica S.r.l. are made available for general information purposes.
•It is not permitted to publish or use, in whole or in part, such contents for commercial purposes without the explicit written consent
of Capetti Elettronica S.r.l.
•The reproduction, duplication, modification, sale or resale of this material or part of it is not permitted without the explicit written
consent of Capetti Elettronica S.r.l.
2. General warnings.
•The following information must be read and understood before proceeding with the installation, commissioning and maintenance of
the devices described in this document.
•ATTENTION! Any omission or failure to follow these instructions scrupulously can cause danger.
•ATTENTION! Explosion hazard. In case of batteries substitution, make sure that the type is compatible and complies with the
specifications indicated by the manufacturer.
•In case of batteries substitution, DO NOT disconnect the flat cable which connect the electronic boards without removing batteries
before.
•ALWAYS substitute all the batteries, also in case of one single battery exhausted.
•If the device is powered by a fixed network, make sure you have disconnected the power supply before carrying out any type of
intervention. Failure to comply with this indication can cause damage to people and/or property.
•Follow the manufacturer's suggested warm-up time ( time required to obtain a reliable measurement ) of the transducer.
•Follow the manufacturer's suggested electric wiring of the transducer to measure ( ground shields at a single point, cable length and
section ); voltage measures on distances exceed 15/20 meters are subjected to electromagnetic disturbances. 0÷25mA inputs have a
superior electromagnetic compatibility ( EMC ).
•Avoid passage in cavities with power or high voltage cables.
•The protection and safety measures and the warranty provided by the Manufacturer with the equipment may be compromised if it’s
used in a manner that does not comply with this user manual.
•This equipment complies with CE regulations.
•Modifications or tampering not expressly approved by the Manufacturer could void the user's authorization to operate the equipment.
•This equipment must be installed by qualified personnel and in accordance with national regulations and/or related local requirements.
•Make sure that the object is properly fixed to supports/infrastructures capable of withstanding this load. Make sure proper methods
and materials are used when fixing the equipment to a wall.
•Only service personnel authorized by the manufacturer or personnel expressly authorized by the latter can open the container. There
are no user serviceable parts inside.

WSD10TII
User Manual
PAGE 3/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
3. Description.
The WSD10TII is a datalogger designed to measure 3 input channels to acquire outdoor temperature and inclination, with storage functionality
of samples acquired.
Inclination measurement is performed by a three-axis accelerometer, which allows the device free orientation related to the horizontal surface.
4. Thermometer: working logic.
The value contained in CH1 channel can be sampled every “ Threshold/Following interval ” as the
other channels.
5. Inclinometer: working logic.
a. Measure.
The datalogger furnishes X and Y axis values related to sampled movements after installation and
its position zeroing Such values are reported on channels CH2 and CH3 respectively.
If a value exceeds the maximum or minimum movement range, the measure will be declared as
“invalid”.
Normally these values are the result of a progressive average updated every “ Threshold/Following
interval ”recorded and sent to the gateway every “ Measure interval ”.
For the average to be done correctly, it is necessary that the “ Follower ” function, on CH2 and CH3 channels (active by default), must be enabled.
Otherwise, the average will be performed with the cadence of the " Measure interval ".
The setup of these intervals is configurable and adjustable using WineCapManager software or cloud support.
b. Measure threshold.
Two thresholds for each inclination channel can be setup: two thresholds for CH2 and two thresholds for CH3.
Measure sample will be compared with thresholds values with interval obtained by “ Threshold/Following interval ” value.
c. Value following –Step answer.
Every “ Threshold/Following interval ” will be compared to the “ instant value ” ( average acquired in a time frame of 8 seconds ) with the current
sample.
If the deviation is greater than “ Delta increase ” value or less than “ Delta decrease ” value, configured in setup, measure is placed equal to the
“instant value” and the average initialized again to that value.
This event will be notified with recording and sending the new measure value.
Properly adjusting “ Delta ” values becomes possible manage movements and react to unexpected events without waiting for periods introduced
by average.
The device DOES NOT answer to SHOCK events and cannot be intended able to display dynamic events. An “ unexpected event ” must be
intended as a significant movement related to the quiet position of the device.
d. Installation position zeroing.
After fixing and installation operations, a “6+2” command (refer to Picture 6 - Status table –Wireless mode ) can be issued which performs the
reset of inclination channels.
The command starts a first acquisition which defines the device’s absolute position and, consequently, the axis rotation to align internal
references. At the end of the procedure, the zero value and the axis position will be saved in memory to be recovered in case of device restart.
This procedure lasts around 5 minutes.
Picture 1 - Product image

WSD10TII
User Manual
PAGE 4/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
6. Default configurations.
Device default configurations at the first starting are the following:
•“ Measure interval ” = 60 minutes
•“ Threshold/Following interval ” = 5 minutes
•CH2 and CH3 “ Follower ” = Enabled with “ Delta Increase ” = 6° and “ Delta Decrease ” = 6°
Picture 2 - Device setup (using gateway)
Picture 3 - Channels/Axis correspondance

WSD10TII
User Manual
PAGE 5/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
7. Device pre-set and use mode.
a. Wireless Mode:
No setup operation is needed. Typically, the system is configured in factory, so the device is already associated to the system gateway. The
device is in STANDBY mode ( refer to Picture 5 - Command table ) for which is necessary to start it with the TEST command ( refer to 10 -
Installation procedure. ).
Otherwise, in case the device is in FACTORY RESET mode ( refer to Picture 5 - Command table ), that means it's ready for connecting to an
existing system, in order to associate it, make reference to the “WineCap System - User Manual R30” software manual. It is necessary to use
the WineCapManager software on the PC connected to the gateway that will be linked with the device.
8. Wireless device user interface.
The user interface consists of a “virtual” button that can be activated using the WineCapKey and of a two-colours led.
To give a command, user must approach the WineCapKey to the device’s sensible area and keep it in that position.; the following picture
( Picture 4 - WineCapKey positioning ) shows device’s sensible points.
LED
WineCapKey
Picture 4 - WineCapKey positioning

WSD10TII
User Manual
PAGE 6/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
The following COMMAND table describes the available commands:
WIRELESS MODE COMMAND table
Flash count
Command
Description
1 flash
STATUS
Shows the device STATUS. As answer the led perform a flash sequence
as reported in the STATUS table. If the device is performing the TEST
( refer to TEST command ) this command stops it.
2 flashes
TEST
Enter in TEST mode and transmits status and measurements every 5
seconds. If the device is in STANDBY mode or it is out of radio range,
this command forces the connection procedure to the WSN and the
return to the operative mode. The TEST stops after 120 seconds.
During TEST, the led continuously shows the STATUS to monitor the
received radio signal quality.
CAUTION: Measures acquired during TEST phase are NOT saved.
3 flashes
ENROL
Association to the network: must be used when the device has not yet
been included in a network, starts the entry and association procedure
to the gateway ( refer to “WineCap System - User Manual R30” ).
4 flashes
+ 4 flashes
STANDBY
Temporary device deactivation: the device is stopped. The sampling
process and the radio are/is. turned off losing the connection to the
network. To reactivate, a TEST command is necessary. The STANDBY
command must be given twice to confirm it: at the first sequence the
led flashes alternating RED and GREEN lights, waiting for the second
confirm sequence within 15 seconds. At the command execution the
led flashes as the STANDBY status ( refer to “Picture 6 - Status table –
Wireless mode” ).
5 flashes
+ 5 flashes
FACTORY RESET
The device performs the memory deleting procedure and goes in
STOP status. All samples, configuration and wireless network data
associated are LOST. To reactivate the device a new association and
configuration procedure is necessary ( ENROL command ). Also in this
case, the FACTORY RESET command must be given twice to confirm
it. At the command execution the led flashes as the
“PROBE/DATALOGGER NOT ASSOCIATED” status ( refer to “Picture 6 -
Status table –Wireless mode” ).
6 flashes
+ 2 flashes
CH2 AND CH3
ZEROING
The device performs the inclination channels X and Y axis zeroing
procedure, fixing the device’s absolute position and the consequent
AXIS ROTATION aligning the internal references and saving the ZERO
position.
6 flashes
+ 6 flashes
ZEROING
CANCELLATION
The device performs the cancellation procedure of zeroing operations
on channels 2 and 3. All the initial values are restored.
Picture 5 - Command table

WSD10TII
User Manual
PAGE 7/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
9. Device enrolment.
Not necessary if performed in factory before delivery.
Enrol the device to the wireless network (868MHz/915MHz) referring to the “WineCap System - User Manual R30” . In case the device is already
enCH2ed but in STANDBY status, a TEST command must be issued (refer to Picture 5 - Command table ) .
10. Installation procedure.
After installing the gateway in appropriate place in charge, ( refer to “WineCap System - User Manual R30 ”), be sure that the device is enCH2ed
to the gateway and activated.
Head for the installation point. On the way, to check the quality of the radio coverage, use the "Field Measurer" function.
This function is activated issuing the TEST (refer to Picture 5 - Command table) command: position the WineCapKey in the spot indicated in
Picture 4 - WineCapKey positioning and wait for two AMBER flashes, then remove the WineCapKey from device. The "Field Measurer" function
lasts enabled for two minutes.
To issue commands to the device, place the WineCapKey where indicated.
Once the WineCapKey , is detected, the led periodically emits AMBER flashes with a 2 second cadence.
For each flash, a different command is associated; to confirm the command the WineCapKey must be removed from the sensible area
immediately after the number of flashes corresponding at the desired command. The TEST corresponds to the second pulse and activate the
"Field Measurer" function.
The device will give back the radio signal quality through led flashes:
WIRELESS MODE STATUS Table
FLASH COUNT –WIRELESS MODE
STATUS/RADIO SIGNAL QUALITY
5 green flashes
ACTIVE - Radio signal: Excellent
4 green flashes
ACTIVE - Radio signal: Good
3 green flashes
ACTIVE - Radio signal: Fair
2 amber flashes
ACTIVE - Radio signal: Sufficient
1 red flash
ACTIVE - Radio signal: Insufficient
1 red flash 2” long
OUT OF RANGE
Network searching
2 red flashes 2” long
STANDBY
Radio off - No Logging
Short-long-short red
flashes series
FACTORY RESET
Device not enCH2ed –No logging
Picture 6 - Status table –Wireless mode
Optimize reception selecting the best position: small movements can help.
If the signal is absent or insufficient at the install point, a repeater WR12 should be put between ( refer to “WineCap System - User Manual
R30 ”). The repeater WR12 itself must be in a position where the signal level is at least sufficient.
The network will reconfigure itself automatically; the signal will be good again when the device synchronizes with the repeater WR12 .
The wireless communication will not be reconfigured until completely lost by the device. Because of this, in some cases it could be necessary
to force the operation. In such cases, put the device in STANDBY mode, then run the TEST again ( refer to “WineCap System - User Manual
R30 ”).
NOTE: The display equipped datalogger (WD04T) is recommended, to verify the signal quality during devices installation.

WSD10TII
User Manual
PAGE 8/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
11. Shutting off/Reactivating the device.
If the device is shut off and left unused for a long time, you can issue the STANDBY command (refer to Picture 5 - Command table) . It
corresponds to the command number 4 and must be issued twice to confirm the operation.
Position the WineCapKey in the spot indicated in ( Picture 4 - WineCapKey positioning ), and wait for four AMBER flashes, then remove the
WineCapKey from device. Verify that the device asks for confirmation of STANDBY command with alternate GREEN/RED flashing, then position
again the WineCapKey and wait for four flashes again. The device will confirm the STANDBY status lighting the RED led for 2 seconds twice. To
reactivate the device the TEST command must be issued.

WSD10TII
User Manual
PAGE 9/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
12. Technical Information
Power supply
19Ah - 3,6V type “D” lithium internal battery ( BAT3 )
Battery life (*)
Up to 5years
(samples every 60 minutes and radio signal quality at least
sufficient)
Measures acquired (3 input channels)
•Temperature
•Biaxial inclination
Sampling interval (*)
Selectable from one minute to 24 hours (60 minutes default)
Datalogger capacity
64,000 samples ( for each channel )
Working temperature
•Operative: -30°C ÷ +60°C
•Warehousing: -40°C ÷ +70°C
Radio frequency
ISM 868MHz
Radio coverage
Up to 6Km in line of sight
(can be extended using WR12 battery powered repeaters)
Sealing
IP68
Dimensions
150x150x60mm
Weight
990g
Case material
ABS, Galvanized iron bracket
Mounting
•4 holes - 9mm diameter
•Gluing using optional bracket FIX-WSD10TII
•Magnetic using FIX-MAG-WSD10TII with 28Kg total traction
force
Connections
Wireless
Inclination –Transducer type
Three-axis accelerometer
Inclination –Measure range
+/-6,5000° in all the installation positions.
Automatic zeroing using command issued with WineCapKey
Inclination –Measure resolution
0.0002°
Inclination –Repeatability
±0.0005°
Temperature - Transducer type
NTC10KΩ
Temperature - Measure range
-30°C ÷ +60°C
Temperature –Measure accuracy
•± 0,5°C Range -30°C ÷ 0°C
•± 0,2°C Range 0°C ÷ +60°C
Temperature - Measure resolution
0.01°C
* battery life may be influenced by fieldwork conditions, sampling/measuring interval and system configuration.
** radio coverage can be extended using up to 32 WR12 repeaters (maximum 16 for each path) between the device and the gateway.

WSD10TII
User Manual
PAGE 10/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
13. Mechanical dimensions.
Picture 7 - Mechanical dimensions

WSD10TII
User Manual
PAGE 11/11
WA0425_WSD10TII_User Manual_R02 V6.0
www.capetti.it
14. Reference standards.
EN 61010 -1
For electromagnetic compatibility
EN 61000 - 3 - 2
EN 61000 - 3 - 3
EN 300 220 -2
EN 301 489 - 03
EN 61000 - 6 -1
This symbol indicates that this product is compliant with the European Directive 2011/65/CE that restricts
the use of substances in the manufacturing of electronic devices.
The “WEEE” logo on the label indicates that this product is compliant with the "WEEE" EC Directive. This
symbol (valid only in the European Union countries) indicates that the product it is applied to, MUST
NOT be discarded with ordinary household or industrial waste, but must be sent to an authorized
reception point. The end user should contact the device provider, either the manufacturer or the reseller,
to agree a collection and disposal process, after having checked the terms and conditions of sale.
IT1902000001116
1