Capetti Elettronica MWLI-MB User manual

Technical Assistance:
eMail [email protected]
Phone [phone]
Mobile [phone]
WA0326E-MWLI-MB_Quick Guide_R05
MWLI-MB
Quick Guide
www.capetti.it

System Components Notes
MWLI-MB
Power Supply
WSN
Antenna
(ANT-EXT)
WineCapKey
USB
Cable
SW WineCapManager
LED
Indicators
12/24V
+ -
2
CAUTION: power up only AFTER
connections are done

Notes Terminal Block
J1
Vin
1
P.E.
2
GND
3
12/24 Vdc
J6
Modbus
1
N.C.
2
MB A+
3
MB B-
4
GND
J6
1
1
J1
3
10

Led Description WineCap Manager
1.Launch Setup.exe in the folder
WineCapManager and run the
installation.
2.Run WineCapManager and select
“Local Connection”.
3.Wait for the MWDG-MB
recognition
4.Create a new database, insert a
database name and press “open”.
5.Insert the license file available
on CD, menu Basestation Insert
license
Wait for the automatic
synchronization of the sensor list
and status from Basestation to PC.
LED
System
System indicator:
slow flash=ok
rapid flash=probe enrolling
Logger
Not used
CCS
Not used
COM
Not used
WSN
Wireless Sensor Network
Green=receiving measures
Red= ongoing transmission
4
9

USB Driver
1.Connect to PC using USB cable.
2.Access to Control Panel Device
Manager and click on MWDG-MB
device.
3.Install USB driver manually
located on CD. File
“MWDG_CDC.inf”
4.Click on “continue” when requested
5.Note for WIN8.1: in case of
malfunctions look at the manual
“Win8.x Installare Drivers USB
R01.pdf” located on CD.
6.At the end of the installation
process, a new COM por twill be
installed: “WineCap MWDG (CDC)”
Start Sensors
1. Connect the MWDG-MB as shown
2. Power on the MWDG-MB and verify
the “System”Led: green flashing
3. Activate the probe
a. Approach the WineCapKey
b. Wait for 2 flashes (test)
4. Remove the Key
5. Verify the LED:
LED FLASHES
RADIO SIGNAL
QUALITY
5 green
flashes
Excellent
4 green
flashes
Good
3 green
flashes
Fair
2 amber
flashes
Sufficient
1 red flash
Insufficient
1 red flash, 2
seconds long
Out of range –
network search
8
5
Temperature
Probe
WSD00T
WineCapKey

How To Install
guide lines to follow during the
system installation process
1. Position at the intended location
and power on the MWDG-MB
a. If possible, choose a central
position among to the wireless
plant
b. Avoid metal obstructions and
reinforced concrete structures
c. Verify the GSM signal
WSN and GSM antennas
distance must be >50cm
2. Move the probe in the selected
location
a. verify the quality of radio signal:
important: small movements can
help
b. outdoor probes must be placed
upward and north oriented to
avoid tampering
3. Adding routers to extend the
radio signal
a. Couple a router to the system
and write down the assigned
address
b. Position the router upward among
obstacles and people
c. Select a “strategic” point among
the plant
4. Using the WD04T tester probe
a. Couple the probe to the system
b. Activated the test, the probe
displays the percentage of the
radio signal level
c. Declares the radio reference in a
specific point: router address or
zero for MWDG-MB
4. Manual: Refer to “WINECAP User
Manual.pdf” located on CD for
further instructions regarding
the network and the installation
process.
6
7