Capetti Elettronica WSD15TIIDR User manual

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
1/11
1. Description.
The WSD15TIIDR is a datalogger with 3 input channels to acquire, Biaxial inclination, and Outdoor temperature, with storage
functionality of samples acquired.
2. Configuration.
Printed on the external label, the correspondence between the measured axes and the number of recorded measure channels is
reported, by means of the three icons below:
Picture 1 - Product Image
X
X
Picture 2 - WSD15TIIDR - Channels/axes correspondence
X

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
2/11
The front side of the cube corresponds to the labelled side, meanwhile the black one represents the side the drawn rotation refers
to, including versus.
In Picture 6 - Device positioning the WSD15TIIDR’s CH2 measures tilt related to the horizontal axis parallel to the wall, positive in
the frontal sense, meanwhile the CH3 is the side tilt around the axis normal to the surface, positive when measured
counterclockwise.
Fix the FIX-WSD15 support slab searching for the best vertical position.
Issuing TEST command, samples acquired can be forced to be sent to basestation for a quick check. (refer to 2.1 - “ELECTRONIC LEVEL”
feature.)
Working on slab’s regulation, sensor position can be corrected and the device can be placed as vertical as possible.
NOTE: antenna must be facing downwards.
2.1. “ELECTRONIC LEVEL”feature.
Activate the axis reset procedure for channel 2 placing the WineCapKey in the upper left corner and counting 6 amber flashes.
Led will flash based on the measured tilt.
RED flashes or GREEN flashes indicates an off-axis position in one of the two directions.
The flashing rate increases in proximity of the zero point.
Operating on fine tune screws, the zero point can be approached until alternate RED and GREEN flashes are shown. In this
condition, the device is within a range of +/-0.1°.
The electronic level stops automatically after a 2 minutes timeout, or it can be stopped manually with the command 1.
Alternatively, repeat command 6 when the alignment has been reached, thus resetting the instrument to the current position
(refer to 2.2 - “RESET READING” Feature).
Up
2
2
3
3
2
Axes regulation
nuts
3
Picture 3 - FIX-WSD15 Micrometric regulation slab

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
3/11
2.2. “RESET READING” Feature
Issue command 6 twice in a row to activate the measure reset process.
The first command activates the ELECTRONIC LEVEL function, useful in order to improve the tool's position, meanwhile the second
instance of the command stores the current position as initial offset.
In case of an unintentional reset, it is always possible to place again the tool near the mechanical zero (using “ELECTRONIC LEVEL”
feature.), and repeat the reset process.
WineCapManager software shows and if necessary reset the offset stored in the datalogger using a remote radio command.
ELECTRONIC LEVEL and RESET READING features are available and works the same for the second tilt channel (channel 3).
Issue command 7 to use these features on channel 3: the first time for the ELECTRONIC LEVEL, twice for RESET READING.
Picture 4 - “ELECTRONIC LEVEL” feature on CH2
Picture 5 - “ELECTRONIC LEVEL” feature on CH3

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
4/11
3. Device preset and use mode.
Wireless Mode:
No setup operation is needed. Typically the system is configured from factory so the device is already associated to the system
basestation. The device is in STANDBY mode (refer to Picture 9 - Status table - Radio signal quality) for which is necessary to start it
with the TEST command (refer to Installation procedure.).
Otherwise, in case the device is in FACTORY RESET mode (refer to Picture 9 - Status table - Radio signal quality), that means it's ready
for connecting to an existing system, in order to associate it, make reference to the “WineCap System - User Manual R29”software
manual. Is necessary to use the "WineCapManager" software on the PC connected to the basestation that will be coupled with
the device.
USB Logger Mode:
For this operation mode, stand-alone with data downloads through USB, the connection with the PC and the
“WineCapManager” running on it is necessary in order to modify the device 's operation mode. The sampling interval must be
set with the device in "STAND-ALONE" (refer to Stand-alone USB datalogger installation.) mode and automatically, the device 's clock
is aligned with the PC's clock, in order to assure the temporal reference of the sample.
Sampling operations start may be selected disconnecting the USB cable or giving the proper command with the magnetic key.
(refer to Stand-alone USB datalogger installation.). More details on device 's connection/disconnection through the USB cable are
available on the WineCap System - User Manual R29 manual.
On field transition from USB to Wireless datalogger:
This transition is practicable in field, during the sampling period, using the wireless network association command. When the
association is done, the datalogger becomes a wireless datalogger and, besides sending new measures to the basestation,
starts a download process towards the same basestation of the measures acquired during the stand alone period (refer to
Picture 10 - Stand-alone datalogger status).
Picture 6 - Device positioning

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
5/11
4. Wireless device user interface.
The user interface consists of a “virtual” button that can be activated using the WineCapKey and of a two-coloured led.
To give a command, user must approach the WineCapKey to the device’s sensible area and keep it in that position.; the following
picture (Picture 7 - WineCapKey positioning) shows device’s sensible points.
Picture 7 - WineCapKey positioning
LED
WineCapKey

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
6/11
The following COMMAND table describes the available commands:
Flash count
Command
Description
1 flash
STATUS
Shows the device STATUS. As answer the led perform a flash sequence as
reported in the “STATUS” table. If the device is performing the TEST (refer to TEST
command) this command stops it.
2 flashes
TEST
Enter in TEST mode and transmits status and measurements every 5 seconds. If
the device is in STANDBY mode or it is out of radio range, this command forces
the connection procedure to the WSN and the return to the operative mode. The
TEST stops after 120 seconds. During TEST the led continuously shows the
STATUS to monitor the received radio signal quality.
CAUTION: Measures acquired during TEST phase are NOT saved.
3 flashes
ENROLL
Association to the network: must be used when the device has not yet been
included in a network, starts the entry and association procedure to the
basestation (refer to “WineCap System - User Manual R29”).
4 flashes
+ 4 flashes
STANDBY
Temporary device deactivation: the device is stopped. The sampling process and
the radio are/is turned off losing the connection to the network. To reactivate, a
TEST command is necessary. The STANDBY command must be given twice to
confirm it: at the first sequence the led flashes alternating RED and GREEN lights,
waiting for the second confirm sequence within 15 seconds. At the command
execution the led flashes as the STANDBY status (refer to “WIRELESS MODE STATUS
Table”).
5 flashes
+ 5 flashes
FACTORY
RESET
The device performs the memory deleting procedure and goes in STOP status. All
samples, configuration and wireless network data associated are LOST. To
reactivate the device a new association and configuration procedure is necessary
(ENROLL command). Also in this case, the FACTORY RESET command must be given
twice to confirm it. At the command execution the led flashes as the
“PROBE/DATALOGGER NOT ASSOCIATED” status refer to “WIRELESS MODE STATUS
Table”).
5 flashes
+ 3 flashes
LOGGER
NO WSN
As the previous command but performs only the WSN deleting procedure and
disassociate from the basestation. The device enter in LOGGER STAND ALONE
mode: data are kept and the sampling activity CONTINUES with previous setup.
Command must be given with 2 sequences: 5 flashes and then 3 flashes. At the
command execution wait for the device reboot. At the STATUS command,
“LOGGER” will be the answer (refer to “STAND-ALONE MODE STATUS Table”). A new
association (ENROLL command) is possible to a new basestation.
Picture 8 - Commands table

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
7/11
5. Enrolling the device.
Not necessary if performed in factory before delivery.
Enroll the device to the network referring to the “WineCap System - User Manual R29”. In case the device is already enrolled but in
STANDBY status, a TEST command must be issued (refer to Picture 8 - Commands table).
6. Installation procedure.
After installing the basestation in appropriate place in charge, (refer to “WineCap System - User Manual R29”), be sure that the device is
enrolled to the basestation and activated.
Head for the environment to be monitored. On the way, to check the quality of the radio coverage, use the "Field Measurer"
function.
This function is activated issuing the TEST (refer to Picture 8 - Commands table)command: position the WineCapKey in the spot
indicated in Picture 7 - WineCapKey positioning and wait for two AMBER flashes, then remove the WineCapKey from device. The
"Field Measurer" function lasts enabled for two minutes.
To issue commands to the device, place the WineCapKey where indicated.
Once the WineCapKey is detected, the led periodically emits AMBER flashes with a 2 seconds cadence.
For each flash, a different command is associated; to confirm the command the WineCapKey must be removed from the sensible
area immediately after the number of flashes corresponding at the desired command. The TEST corresponds to the second pulse
and activate the "Field Measurer" function.
The device will give back the radio signal quality through led flashes:
WIRELESS MODE STATUS Table
Flash count - Wireless mode
Status/Radio signal quality
5 green flashes
Excellent
4 green flashes
Good
3 green flashes
Fair
2 amber flashes
Sufficient
1 red flash
Insufficient
1 red flash 2” long
OUT OF RANGE
Network searching
2 red flashes 2” long
STANDBY
Short-long-short red
flashes series
FACTORY RESET
Device not enrolled
Optimize reception selecting the best position: small movements can help.
If the signal is absent or insufficient at the install point, a WR12 router should be put between (refer to “WineCap System - User Manual
R29”). The WR12 router itself must be located in a position where the signal level is at least sufficient.
The network will reconfigure itself automatically; the signal will be good again when the device synchronizes with the WR12 router.
The link will not be reconfigured until completely lost by the device. Because of this, in some cases it could be necessary to force
the operation. In such cases, put the device in STANDBY mode, then run the TEST again (refer to “WineCap System - User Manual R29”).
NOTE: The display equipped datalogger (WD04T) is recommended, to verify the signal quality during devices installation.
Picture 9 - Status table - Radio signal quality

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
8/11
7. Stand-alone USB datalogger installation.
Install the datalogger in appropriate place.
If the sampling process has not yet been activated you can start it through the WineCapKey.
Bring it closer to the sensitive point, wait for 2 flashes (TEST) (refer to Picture 8 - Commands table) and remove. The datalogger begins
sampling according to your settings through your PC.
Through the WineCapKey is possible to ask for the current status, bring it close to the datalogger for 1 flash (STATE) and remove it.
STAND-ALONE MODE STATUS Table:
Flash count - Stand-alone mode
STATUS
1 green flash 2 seconds long
ACTIVE
2 red flashes 2 seconds long
STANDBY
Sequence of red flashes: short, 2
seconds long, short
FACTORY RESET
INVALID datalogger clock!
PC connection required
8. Shutting off/Reactivating the device.
If the device is shut off and left unused for a long time, you can issue the STANDBY command (refer to Picture 8 - Commands table). Its
corresponds to the command number 4 and must be issued twice to confirm the operation.
Position the WineCapKey in the spot indicated in Picture 7 - WineCapKey positioning and wait for four AMBER flashes, then remove
the WineCapKey from device.
Verify that the device asks for confirmation of STANDBY command with alternate GREEN/RED flashing, then position again the
WineCapKey and wait for four flashes again. The device will confirm the STANDBY status lighting the RED led for 2 seconds twice.
To reactivate the device the TEST command must be issued.
Picture 10 - Stand-alone datalogger status

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
9/11
9. Technical Information.
Power supply
8.5A/h - 3.6V type “C” lithium internal battery
Battery life (*)
Up to 5years
(samples every 60 minutes and radio signal quality at least sufficient)
Measures acquired (3 input channels
Biaxial inclination
Outdoor temperature
Sampling interval (*)
Selectable from one minute to 24 hours (60 minutes default)
Datalogger capacity
64,000 sample (for each channel)
Working temperature
Operative: -30°C ÷ +60°C
Warehousing: -40°C ÷ +70°C
Radio frequency
ISM 868MHz
Radio coverage
Up to 6Km in line of sight
(can be extended using WR12 battery powered routers)
Sealing
IP67
Dimensions
100x100x80mm
Weight
1,6000g
Case material
Aluminium
Mounting
Wall mounting with ±2° gross setting
Connections
Wireless, USB
Inclination - Transducer type
Uniaxial/Biaxial/Triaxial - MEMS technology - 1°÷15° Dual Range
Automatic Autoscale
Inclination - Measure range
±1°/±15°
Inclination - Measure accuracy
± 0.5% of sample
Inclination - Measure resolution
0.001° (±1° range) - 0.01° (±15° range)
Inclination - Mechanical zero adjustment
±4°
Inclination - Cross-axis sensitivity
4% maximum
Inclination - Temperature variation sensibility
±0.013%/°C Temperature balance
Inclination - Shock resistance
20,000g
Inclination - Measure axis
Abscissa
Outdoor temperature - Transducer type
NTC10KΩ
Outdoor temperature - Measure range
-30°C ÷ +60°C
Outdoor temperature - Measure accuracy
± 0.5°C Range -30°C ÷ 0°C
± 0.2°C Range 0°C ÷ +60°C
Outdoor temperature - Measure resolution
0.01°C
* battery life may be influenced by fieldwork conditions, sampling interval and system configuration.
** radio coverage reachable using up to 32 WR12 routers (maximum 16 for each path) between the device and the basestation.

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
10/11
10. Mechanical dimensions.
Picture 11 - Mechanical dimensions

WSD15TIIDR
User Manual
WA0140E_WSD15TIIDR User Manual_R11
V4.7
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
11/11
11. Reference standards.
EN 61010 -1
For electromagnetic compatibility
EN 61000 - 3 - 2
EN 61000 - 3 - 3
EN 300 220 -2
EN 301 489 - 03
EN 61000 - 6 -1
This symbol indicates that this product is compliant with the European Directive 2011/65/CE that restricts
the use of substances in the manufacturing of electronic devices.
The “WEEE” logo on the label indicates that this product is compliant with the "WEEE" EC Directive.This
symbol (valid only in the European Union countries) indicates that the product it is applied to, MUST NOT
be discarded with ordinary household or industrial waste, but must be sent to an authorized reception
point. The end user should contact the device provider, either the manufacturer or the reseller, in order to
agree a collection and disposal process, after having checked the terms and conditions of sale.
The features shown may be subject to change without notice.
IT190200000111
61