Capetti Elettronica WSD00T User manual

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
1/8
WSD00T / WSD00T_LD
User Manual
1. Description.
The WSD00T and the WSD00T_LD are dataloggers with one input channels to acquire indoor temperature, with storage
functionality of samples acquired.
2. Device preset and use mode.
a. Wireless Mode:
No setup operation is needed. Typically the system is configured from factory so the device is already associated to the system
basestation. The device is in STANDBY mode for which is necessary to start it with the TEST command (refer to chapter 5 -
Installation procedure.).
Otherwise, in case the device is in FACTORY RESET mode, that means it's ready for connecting to an existing system, in order to
associate it, make reference to the “WineCap System - User Manual R28 - chapter 4.3.1 Probe/datalogger association procedure.”
software manual. Is necessary to use the "WineCapManager" software on the PC connected to the basestation that will be
coupled with the device.
b. USB Logger Mode:
For this operation mode, stand-alone with data downloads through USB, the connection with the PC and the
“WineCapManager” running on it is necessary in order to modify the device 's operation mode. The sampling interval must be
set with the device in "STAND-ALONE" mode and automatically, the device 's clock is aligned with the PC's clock, in order to
assure the temporal reference of the sample.
Sampling operations start may be selected disconnecting the USB cable or giving the proper command with the magnetic key.
(refer chapter 6- Stand-alone USB datalogger installation.). More details on device 's connection/disconnection through the USB
cable are available on the WineCap System - User Manual R28 manual.
c. On field transition from USB to Wireless datalogger:
This transition is practicable in field, during the sampling period, using the wireless network association command. When the
association is done, the datalogger becomes a wireless datalogger and, besides sending new measures to the basestation,
starts a download process towards the same basestation of the measures acquired during the stand alone period.
Picture 1 - Product Image

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
2/8
WSD00T / WSD00T_LD
User Manual
3. Wireless device user interface.
The user interface consists of a “virtual” button that can be activated using the WineCapKey and of a two-coloured led.
To give a command, user must approach the WineCapKey to the device’s sensible area and keep it in that position.; the following
picture (Pic. 3) shows device’s sensible points.
Picture 2 - Device positioning
Picture 3 - WineCapKey positioning
WineCapKey
LED
WineCapKey
LED

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
3/8
WSD00T / WSD00T_LD
User Manual
The following COMMAND table describes the available commands:
Flash count
Command
Description
1 flash
STATUS
Shows the device STATUS. As answer the led perform a flash sequence as
reported in the “STATUS” table. If the device is performing the TEST (refer to TEST
command) this command stops it.
2 flashes
TEST
Enter in TEST mode and transmits status and measurements every 5 seconds. If
the device is in STANDBY mode or it is out of radio range, this command forces
the connection procedure to the WSN and the return to the operative mode. The
TEST stops after 120 seconds. During TEST the led continuously shows the
STATUS to monitor the received radio signal quality.
CAUTION: Measures acquired during TEST phase are NOT saved.
3 flashes
ENROLL
Association to the network: must be used when the device has not yet been
included in a network, starts the entry and association procedure to the
basestation (refer to “WineCap System - User Manual R28 - chapter 4.3.1 Probe/datalogger
association procedure”).
4 flashes
+ 4 flashes
STANDBY
Temporary device deactivation: the device is stopped. The sampling process and
the radio are/is turned off losing the connection to the network. To reactivate, a
TEST command is necessary. The STANDBY command must be given twice to
confirm it: at the first sequence the led flashes alternating RED and GREEN lights,
waiting for the second confirm sequence within 15 seconds. At the command
execution the led flashes as the STANDBY status (refer to “Picture 5 - Status table -
Radio signal quality”).
5 flashes
+ 5 flashes
FACTORY
RESET
The device performs the memory deleting procedure and goes in STOP status. All
samples, configuration and wireless network data associated are LOST. To
reactivate the device a new association and configuration procedure is necessary
(ENROLL command). Also in this case, the FACTORY RESET command must be given
twice to confirm it. At the command execution the led flashes as the
“PROBE/DATALOGGER NOT ASSOCIATED” status (refer to “Picture 5 - Status table -
Radio signal quality”).
5 flashes
+ 3 flashes
LOGGER
NO WSN
As the previous command but performs only the WSN deleting procedure and
disassociate from the basestation. The device enter in LOGGER STAND ALONE
mode: data are kept and the sampling activity CONTINUES with previous setup.
Command must be given with 2 sequences: 5 flashes and then 3 flashes. At the
command execution wait for the device reboot. At the STATUS command,
“LOGGER” will be the answer (refer to “Picture 6 - Stand-alone datalogger status”). A
new association (ENROLL command) is possible to a new basestation.
4. Enrolling the device.
Enroll the device to the network referring to the “WineCap System - User Manual R28”. In case the device is already enrolled but in
STANDBY status, a TEST command must be issued.
5. Installation procedure.
After installing the basestation in appropriate place in charge, (refer to “WineCap System - User Manual R28”), be sure that the device is
enrolled to the basestation and activated.
Head for the environment to be monitored. On the way, to check the quality of the radio coverage, use the "Field Measurer"
function.
This function is activated issuing the TEST command: position the WineCapKey in the spot indicated in Picture (Picture 3) and wait for
two AMBER flashes, then remove the WineCapKey from device. The "Field Measurer" function lasts enabled for two minutes.
To issue commands to the device, place the WineCapKey where indicated.
Picture 4 - Commands table

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
4/8
WSD00T / WSD00T_LD
User Manual
Once the WineCapKey is detected, the led periodically emits AMBER flashes with a 2 seconds cadence.
For each flash, a different command is associated; to confirm the command the WineCapKey must be removed from the sensible
area immediately after the number of flashes corresponding at the desired command. The TEST corresponds to the second pulse
and activate the "Field Measurer" function.
The device will give back the radio signal quality through led flashes:
STATUS Table
Flash count - Wireless mode
Status/Radio signal quality
5 green flashes
Excellent
4 green flashes
Good
3 green flashes
Fair
2 amber flashes
Sufficient
1 red flash
Insufficient
1 red flash 2” long
OUT OF RANGE
Network searching
2 red flashes 2” long
STANDBY
Short-long-short red
flashes series
FACTORY RESET
Device not enrolled
Optimize reception selecting the best position: small movements can help.
If the signal is absent or insufficient at the install point, a WR12 router should be put between (refer to "WineCapManager User
Manual). The WR12 router itself must be located in a position where the signal level is at least sufficient.
The network will reconfigure itself automatically; the signal will be good again when the device synchronizes with the WR12 router.
The link will not be reconfigured until completely lost by the device. Because of this, in some cases it could be necessary to force
the operation. In such cases, put the device in STANDBY mode, then run the TEST again (refer to “WineCap System - User Manual R28”).
NOTE: The display equipped datalogger (WD04T) is recommended, to verify the signal quality during devices installation.
Picture 5 - Status table - Radio signal quality

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
5/8
WSD00T / WSD00T_LD
User Manual
6. Stand-alone USB datalogger installation.
Install the datalogger in appropriate place.
If the sampling process has not yet been activated you can start it through the WineCapKey.
Bring it closer to the sensitive point, wait for 2 flashes (TEST) and remove. The datalogger begins sampling according to your
settings through your PC.
Through the WineCapKey is possible to ask for the current status, bring it close to the datalogger for 1 flash (STATE) and remove it.
STATUS Table:
Flash count - Stand-alone mode
STATUS
1 green flash 2 seconds long
ACTIVE
2 red flashes 2 seconds long
STANDBY
Sequence of red flashes: short, 2
seconds long, short
FACTORY RESET
INVALID datalogger clock!
PC connection required
7. Shutting off/Reactivating the device.
If the device is shut off and left unused for a long time, you can issue the STANDBY command. Its corresponds to the command
number 4 and must be issued twice to confirm the operation.
Position the WineCapKey in the spot indicated in Picture 3 and wait for four AMBER flashes, then remove the WineCapKey from
device.
Verify that the device asks for confirmation of STANDBY command with alternate GREEN/RED flashing, then position again the
WineCapKey and wait for four flashes again. The device will confirm the STANDBY status lighting the RED led for 2 seconds twice.
To reactivate the device the TEST command must be issued.
Picture 6 - Stand-alone datalogger status

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
6/8
WSD00T / WSD00T_LD
User Manual
8. Technical Information.
Power supply
WSD00T: 2.4A/h - 3.6V type “AA” lithium internal battery
WSD00T_LD: 8.5A/h - 3.6V type “C” lithium internal battery
Battery life (*)
WSD00T: Up to 5 years
WSD00T_LD: Up to 12 years
(samples every 10 minutes and radio signal quality at least sufficient)
Measures acquired (1 channel)
Indoor temperature
Sampling interval (*)
Selectable from one minute to 24 hours (10 minutes default)
Datalogger capacity
128,000 samples (for each channel)
Working temperature
Operative: -30°C ÷ +60°C
Warehousing: -40°C ÷ +70°C
Radio frequency
ISM 868MHz
Radio coverage (**)
Up to 6Km in line of sight
(can be extended using WR12 battery powered routers)
Sealing
IP30
Dimensions
WSD00T: 80 x 80 x 25mm
WSD00T_LD: 120 x 80 x 33.5mm
Weight
WSD00T: 100g
WSD00T_LD: 224g
Case material
ABS
Mounting
Fix on 2/4 points
Connections
Wireless/USB
Temperature - Transducer type
NTC10KΩ
Temperature - Measure range
-10°C ÷ +60°C
Temperature - Measure accuracy
±0.2°C in whole range
Temperature - Measure resolution
0.01°C
* battery life may be influenced by fieldwork conditions, sampling interval and system configuration.
** radio coverage reachable using up to 32 WR12 routers (maximum 16 for each path) between the device and the basestation.

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
7/8
WSD00T / WSD00T_LD
User Manual
9. Mechanical dimensions.
Picture 7 - Mechanical dimensions

WA0123E_WSD00T/WSD00T_LD_User Manual_R10
CAPETTI ELETTRONICA s.r.l. - Strada Stratta 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
8/8
WSD00T / WSD00T_LD
User Manual
10. Reference standards.
EN 61010 -1
For electromagnetic compatibility
EN 61000 - 3 - 2
EN 61000 - 3 - 3
EN 300 220 -2
EN 301 489 - 03
EN 61000 - 6 -1
This symbol indicates that this product is compliant with the European Directive 2011/65/CE that restricts
the use of substances in the manufacturing of electronic devices.
The “WEEE” logo on the label indicates that this product is compliant with the "WEEE" EC Directive.This
symbol (valid only in the European Union countries) indicates that the product it is applied to, MUST NOT
be discarded with ordinary household or industrial waste, but must be sent to an authorized reception
point. The end user should contact the device provider, either the manufacturer or the reseller, in order to
agree a collection and disposal process, after having checked the terms and conditions of sale.
The features shown may be subject to change without notice.