Capetti Elettronica WineCap WSD15IIDIST User manual

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
1. Description.
The WSD15IIDIST is a datalogger with 4 channels to acquire biaxial inclination, absolute distance, or temperature (selectable during
installation) and relative distance with storage functionality of samples acquired.
2. Inclinometer: operating logic.
a. Measure.
The datalogger provides the roll and pitch values relating to the displacements suffered after installation and the relative zeroing of
the position and reports them in the channels CH1 and CH2 respectively. If the value exceeds the maximum and minimum
displacement range, the measurement is declared "invalid".
Normally these values are the result of a progressive average updated at each "Threshold / Tracking time", recorded and sent to the
gateway at each "Measurement time". For the average to be carried out correctly, the “Follower” function on the pitch and roll
channel (active by default) must be enabled. Otherwise, the average will be performed with the cadence of the "Measurement
time".
The setting of these times is configurable and modifiable through the WineCapManager software or through the cloud.
b. Measure thresholds.
Two thresholds can be set for each slope measurement channel: two thresholds for rolling and two thresholds for pitching.
The value of the measurement will be compared with the values of these thresholds with a time interval obtained from the
“Threshold / Tracking time” value.
c. Value following –Step response.
At each “Threshold / Tracking time” the “instantaneous value” (average of the acquired values in a window lasting 8 seconds) will
be compared with the current measurement value.
If the difference is greater than the "Delta Increment" value or less than the "Delta Decrement" value, present in the settings, the
measurement is set equal to the "instantaneous value" and the average is reinitialized to that value.
This event will be notified with the recording and sending of the new measurement value.
Picture 1 - Product Image

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
By appropriately adjusting the “Delta” values, it is therefore possible to manage movements and react to sudden events without
waiting for the times introduced by the average.
The device does NOT respond to SHOCK events and cannot be intended for dynamic event displays. By "sudden event" is meant as
significant displacement related to the position of rest in which the instrument is working.
d. Reset installation position.
After installation and fixing, a "6 + 1" command can be issued (see Picture 3 - Commands table), which resets the channels dedicated
to the inclination.
The command starts a first acquisition which determines the absolute position of the tool and the consequent rotation of the axes
to align the internal references. At the end of the procedure, the zero value and the position of the axes are saved in the memory
so that they can be recovered in case of restart of the device.
This procedure takes about 5 minutes.

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
3. Distance meter: operating logic.
The laser pointer acquires the distance. The absolute distance is reported on CH3, while the distance relative to the reset position
is reported on channel CH4. If these values exceed the maximum and minimum displacement range, the measurement is declared
"invalid".
The distance is acquired with the frequency indicated by the “Measurement time” parameter. There are 2 thresholds per channel
which, if activated and configured, bring the acquisition cadence to the "Threshold / Tracking time" (default: disabled).
a. Reset installation position.
By giving the command "6+4" (see Picture 3 - Commands table), the channel dedicated to the measurement of the relative distance is
reset.
b. Laser pointer.
There is a "laser aiming" function: by giving the command "7" (see Picture 3 - Commands table) the laser is activated and allows a
precise aim at the target. This function ceases when a measurement is performed by the datalogger, or if command "7" is given
again.
It is recommended to use a white, non-glossy and possibly smooth material as a target.
4. Thermometer: operating logic.
The value reported on channel CH3 can be configured to provide the temperature acquired by the datalogger which is sampled at
each “Threshold / Tracking time” like the other channels.
To perform the configuration, it is necessary to connect the WSD15IIDIST datalogger to the PC via USB cable and use
WineCapManager. In the “Sensor→Properties” section, on the “Tools” page, it is possible to decide the behaviour of channel 3.
ATTENTION: after this modification it is necessary to enrol the datalogger with the gateway again.
5. Default settings.
The default settings of the device at first start-up are as follows:
•“Measurement time” = 60 minutes
•“Threshold / Tracking time” = 5 minutes
•CH1 e CH2 “Follower” = Active with “Delta Increment”= 6° and “Delta Decrement”= 6° values
•CH3 setup as ABSOLUTE DISTANCE

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
6. Device pre-set and use mode.
a. Wireless Mode:
No setup operation is needed. Typically, the system is configured from factory, so the device is already associated to the system
basestation. The device is in STANDBY mode (refer to Picture 4 - Status table - Radio signal quality) for which is necessary to start it
with the TEST command (refer to 9 - Installation procedure.).
Otherwise, in case the device is in FACTORY RESET mode (refer to Picture 4 - Status table - Radio signal quality), that means it's ready
for connecting to an existing system, in order to associate it, make reference to the “WineCap System - User Manual R30”
software manual. Is necessary to use the "WineCapManager" software on the PC connected to the basestation that will be
coupled with the device.
b. USB Logger Mode:
For this operation mode, stand-alone with data downloads through USB, the connection with the PC and the “WineCapManager”
running on it is necessary in order to modify the device 's operation mode. The sampling interval must be set with the device in
"STAND-ALONE" (refer to 7) mode and automatically, the device 's clock is aligned with the PC's clock, to assure the temporal
reference of the sample.
Sampling operations start may be selected disconnecting the USB cable or giving the proper command with the magnetic key.
(refer to 10 - Stand-alone USB datalogger installation.). More details on device 's connection/disconnection through the USB cable are
available on the WineCap System - User Manual R30 manual.
c. On field transition from USB to Wireless datalogger:
This transition is practicable in field, during the sampling period, using the wireless network association command. When the
association is done, the datalogger becomes a wireless datalogger and, besides sending new measures to the basestation, starts
a download process towards the same basestation of the measures acquired during the stand-alone period (refer to Picture 5 -
Stand-alone datalogger status).
7. Wireless device user interface.
The user interface consists of a “virtual” button that can be activated using the WineCapKey and of a two-colors led.
To give a command, user must approach the WineCapKey to the device’s sensible area and keep it in that position.; the following
picture (Picture 2 - WineCapKey positioning) shows device’s sensible points.
Picture 2 - WineCapKey positioning
LED

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
The following COMMAND table describes the available commands:
Flash count
Command
Description
1 flash
STATUS
Shows the device STATUS. As answer the led perform a flash sequence as reported
in the “STATUS” table. If the device is performing the TEST (refer to TEST command)
this command stops it.
2 flashes
TEST
Enter in TEST mode and transmits status and measurements every 5 seconds. If
the device is in STANDBY mode or it is out of radio range, this command forces the
connection procedure to the WSN and the return to the operative mode. The TEST
stops after 120 seconds. During TEST, the led continuously shows the STATUS to
monitor the received radio signal quality.
CAUTION: Measures acquired during TEST phase are NOT saved.
3 flashes
ENROLL
Association to the network: must be used when the device has not yet been
included in a network, starts the entry and association procedure to the
basestation (refer to “WineCap System - User Manual R30”).
4 flashes
+ 4 flashes
STANDBY
Temporary device deactivation: the device is stopped. The sampling process and
the radio are/is turned off losing the connection to the network. To reactivate, a
TEST command is necessary. The STANDBY command must be given twice to
confirm it: at the first sequence the led flashes alternating RED and GREEN lights,
waiting for the second confirm sequence within 15 seconds. At the command
execution the led flashes as the STANDBY status (refer to “WIRELESS MODE STATUS
Table”).
5 flashes
+ 5 flashes
FACTORY
RESET
The device performs the memory deleting procedure and goes in STOP status. All
samples, configuration and wireless network data associated are LOST. To
reactivate the device a new association and configuration procedure is necessary
(ENROLL command). Also in this case, the FACTORY RESET command must be given
twice to confirm it. At the command execution the led flashes as the
“PROBE/DATALOGGER NOT ASSOCIATED” status refer to “WIRELESS MODE STATUS
Table”).
5 flashes
+ 3 flashes
LOGGER
NO WSN
As the previous command but performs only the WSN deleting procedure and
disassociate from the basestation. The device enters in LOGGER STAND ALONE
mode: data are kept, and the sampling activity CONTINUES with previous setup.
Command must be given with 2 sequences: 5 flashes and then 3 flashes. At the
command execution wait for the device reboot. At the STATUS command,
“LOGGER” will be the answer (refer to “STAND-ALONE MODE STATUS Table”). A new
association (ENROLL command) is possible to a new basestation.
6 flashes
+ 1 flash
CH1 and CH2
Reset
The device carries out the procedure of zeroing the inclination channels of the X
and Y axes, determining the absolute position of the instrument and the
consequent ROTATION OF THE AXES, aligning the internal references and saving
the ZERO position.
6 flashes
+ 4 flashes
CH4
Reset
The device carries out the zeroing procedure of the relative distance acquisition
channel
6 flashes
+ 6 flashes
Cancellation
of resets
The device performs the procedure for cancelling all the zeroing operations carried
out on channels 1, 2 and 4. The initial values are restored.
7 flashes
Pointing
The laser pointer is turned on. To interrupt this phase, it is necessary to issue the
command again or wait for the next measurement.
Picture 3 - Commands table

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
8. Enrolling the device.
Not necessary if performed in factory before delivery.
Enroll the device to the network referring to the “WineCap System - User Manual R30”. In case the device is already enrolled but in
STANDBY status, a TEST command must be issued (refer to Picture 3 - Commands table).
9. Installation procedure.
After installing the basestation in appropriate place in charge, (refer to “WineCap System - User Manual R30”), be sure that the device is
enrolled to the basestation and activated.
Head for the environment to be monitored. On the way, to check the quality of the radio coverage, use the "Field Measurer" function.
This function is activated issuing the TEST (refer to Picture 3 - Commands table)command: position the WineCapKey in the spot indicated
in Picture 2 - WineCapKey positioning and wait for two AMBER flashes, then remove the WineCapKey from device. The "Field
Measurer" function lasts enabled for two minutes.
To issue commands to the device, place the WineCapKey where indicated.
Once the WineCapKey is detected, the led periodically emits AMBER flashes with a 2 second cadence.
For each flash, a different command is associated; to confirm the command the WineCapKey must be removed from the sensible
area immediately after the number of flashes corresponding at the desired command. The TEST corresponds to the second pulse and
activate the "Field Measurer" function.
The device will give back the radio signal quality through led flashes:
WIRELESS MODE STATUS Table
Flash count - Wireless mode
Status/Radio signal quality
5 green flashes
Excellent
4 green flashes
Good
3 green flashes
Fair
2 amber flashes
Sufficient
1 red flash
Insufficient
1 red flash 2” long
OUT OF RANGE
Network searching
2 red flashes 2” long
STANDBY
Short-long-short red
flashes series
FACTORY RESET
Device not enrolled
Optimize reception selecting the best position: small movements can help.
If the signal is absent or insufficient at the install point, a WR12 repeater should be put between (refer to “WineCap System - User Manual
R30”). The WR12 repeater itself must be in a position where the signal level is at least sufficient.
The network will reconfigure itself automatically; the signal will be good again when the device synchronizes with the WR12 repeater.
The link will not be reconfigured until completely lost by the device. Because of this, in some cases it could be necessary to force the
operation. In such cases, put the device in STANDBY mode, then run the TEST again (refer to “WineCap System - User Manual R30”).
NOTE: The display equipped datalogger (WD04T) is recommended, to verify the signal quality during devices installation.
Picture 4 - Status table - Radio signal quality

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
10. Stand-alone USB datalogger installation.
Install the datalogger in appropriate place.
If the sampling process has not yet been activated, you can start it through the WineCapKey.
Bring it closer to the sensitive point, wait for 2 flashes (TEST) (refer to Picture 3 - Commands table) and remove. The datalogger begins
sampling according to your settings through your PC.
Through the WineCapKey is possible to ask for the status, bring it close to the datalogger for 1 flash (STATE) and remove it.
STAND-ALONE MODE STATUS Table:
Flash count - Stand-alone mode
STATUS
1 green flash 2 seconds long
ACTIVE
2 red flashes 2 seconds long
STANDBY
Sequence of red flashes: short, 2
seconds long, short
FACTORY RESET
INVALID datalogger clock!
PC connection required
11. Shutting off/Reactivating the device.
If the device is shut off and left unused for a long time, you can issue the STANDBY command (refer to Picture 3 - Commands table). It
corresponds to the command number 4 and must be issued twice to confirm the operation.
Position the WineCapKey in the spot indicated in Picture 2 - WineCapKey positioning and wait for four AMBER flashes, then remove
the WineCapKey from device.
Verify that the device asks for confirmation of STANDBY command with alternate GREEN/RED flashing, then position again the
WineCapKey and wait for four flashes again. The device will confirm the STANDBY status lighting the RED led for 2 seconds twice.
To reactivate the device the TEST command must be issued.
Picture 5 - Stand-alone datalogger status

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
12. Technical Information.
Power supply
19Ah - 3,6V type “D” lithium internal battery
Battery life (*)
Up to 5years
(samples every 60 minutes and radio signal quality at least sufficient)
Measures acquired (4 input channels)
•Biaxial inclination
•Temperature
•Distance
Sampling interval (*)
Selectable from one minute to 24 hours (60 minutes default)
Datalogger capacity
64,000 samples (for each channel)
Working temperature
•Operative: -30°C ÷ +60°C
•Warehousing: -25°C ÷ +70°C
Radio frequency
ISM 868MHz
Radio coverage
Up to 6Km in line of sight
(can be extended using WR12 battery powered repeaters)
Sealing
IP65
Dimensions
100x100x80mm
Weight
1,6000g
Case material
Aluminium
Mounting
Using basic clamp or optional FIX-DIST clamp
(free adjustment on 2 axis)
Connections
Wireless, USB
Inclination - Transducer type
Three axis accelerometer
Inclination - Measure range
-6,5000° ÷ +6,5000°
Inclination - Measure accuracy
± 0.5% of measure
Inclination - Measure resolution
0.0002°
Temperature - Transducer type
NTC10KΩ
Temperature - Measure range
-30°C ÷ +60°C
Temperature - Measure accuracy
•± 0.5°C Range -30°C ÷ 0°C
•± 0.2°C Range 0°C ÷ +60°C
Temperature - Measure resolution
0.01°C
Relative distance–Transducer type
LASER distance meter
Relative distance –Measure range
+/-3.200mm
Relative distance –Measure resolution
0.1mm
Relative distance –Measure accuracy
±1mm
Relative distance –Repeatability
±0.3mm
Absolute distance –Transducer type
LASER distance meter
Absolute distance –Measure range
0÷65,000mm
Absolute distance –Measure resolution
1mm
Absolute distance –Measure accuracy
±1mm
Absolute distance –Repeatability
±0.3mm
LASER distance meter - Type
Class 2 - 655nm (visible red)
LASER distance meter –Sensor range
65,000mm (matte white target)
LASER distance meter –Temperature range
-10°C ÷ +50°C
LASER distance meter –Measure range
±3,200mm (at absolute distance of 65,000mm)
* battery life may be influenced by fieldwork conditions, sampling interval and system configuration.
** radio coverage can be extended using up to 32 WR12 repeaters (maximum 16 for each path) between the device and the basestation.

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
13. Mechanical dimensions.
14. Warnings.
•The protection and safety measures and the warranty provided by the Manufacturer with the equipment may
be compromised if it’s used in a manner that does not comply with this user manual.
•This equipment complies with CE regulations.
•This equipment can receive any interference which could also cause unwanted behaviour.
•Modifications or tampering not expressly approved by the Manufacturer could void the user's authorization to
operate the equipment.
•This equipment must be installed by qualified personnel.
•This equipment contains a Class 2 laser. The user should avoid pointing the laser directly into the eye while the
device is powered.
•The device has a weight of up to 1.6 kg. Make sure that the object is properly fixed to supports/infrastructures
capable of withstanding this load. Make sure proper methods and materials are used when fixing the
equipment to a wall.
•Only service personnel authorized by the manufacturer or personnel expressly authorized by the latter can
open the container. There are no user serviceable parts inside.
Picture 6 - Mechanical dimensions

WSD15IIDIST
User Manual
CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57
10090 CASTIGLIONE TORINESE - TORINO - ITALY
VAT 04837130014 - Phone [phone] - Fax [phone]
e-mail [email protected] - web www.capetti.it
WA0416E_WSD15IIDIST_User Manual_R05
V5.0
15. Reference standards.
EN 61010 -1
For electromagnetic compatibility
EN 61000 - 3 - 2
EN 61000 - 3 - 3
EN 300 220 -2
EN 301 489 - 03
EN 61000 - 6 -1
This symbol indicates that this product is compliant with the European Directive 2011/65/CE that restricts
the use of substances in the manufacturing of electronic devices.
The “WEEE” logo on the label indicates that this product is compliant with the "WEEE" EC Directive. This
symbol (valid only in the European Union countries) indicates that the product it is applied to, MUST NOT
be discarded with ordinary household or industrial waste, but must be sent to an authorized reception
point. The end user should contact the device provider, either the manufacturer or the reseller, to agree a
collection and disposal process, after having checked the terms and conditions of sale.
The features shown may be subject to change without notice.
IT190200000111
61