Caple Wi6128 User manual

Instruction manual for slot-in wine cabinet
Model code: Wi6128
Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk

Contents
Important safety instructions 3
Installationinstructions 4
Before using your wine cabinet 4
Operating you wine cabinet and setting the temperature 5
Usingtheshelves 6
How to change the door opening 7
Fitting a kitchen plinth 8
Installation dimensions 8
Care and maintenance 9
Troubleshooting guide 10
Caple Service contact details 10
Defrosting/condensation 11
Thehumiditysystem 11
Recommended storage temperatures 11
Recommended drinking temperatures 11

Warnings
zTo prevent damaging the door gasket, make sure the door is fully open when pulling shelves
out of the rail compartment.
zThe appliance must be positioned so that the plug is accessible. Release the electric cord and
move your cabinet to its final location. Do not move your cabinet while loaded with wine as
you may distort the body.
zThe wine cabinet should be installed in a suitable place in order to avoid touching the
compressor with the hand.
zIf the supply cord is damaged, it must be replaced by a Caple service agent or a similarly
qualified person in order to avoid a hazard.
PLEASE DO NOT TRY TO EXTEND THE ELECTRICAL CABLE IN ANY WAY.
Important Safety Instructions
aWARNINGa
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic
precautions:
zRead all instructions before using the wine cabinet.
zDANGER or WARNING:Risk of child entrapment.
zChild entrapment and suffocation are not problems of the past. Junked or abandoned
appliances are still dangerous . . . even if they will “just sit in the garage a few days”.
zBefore you throw away your old wine cabinet: Take off the door, leaving the shelves in place
so that children cannot easily climb inside.
zNever allow children to operate, play with, or crawl inside the appliance.
zNever clean appliance parts with flammable fluids. The fumes can create a fire hazard or
explosion.
zDo not store or use gasoline or any other flammable vapours and liquids in the vicinity of this
or any other appliance. The fumes can create a fire hazard or explosion.
zThe refrigerant of this appliance is R600a, flammable and explosive articles should not be put
in or near the cabinet, to avoid the risk of fire or explosion.
Please keep this instruction manual for future reference
3

Installation instructions
Before using your wine cabinet
•Remove the exterior and interior packing.
•Before connecting the wine cabinet to the power source, let it stand upright for approximately
12 hours. This will reduce the possibility of a malfunction in the cooling system from handling
during transportation.
•Clean the interior surface with lukewarm water using a soft cloth.
•These appliances cannot be disposed of with general waste. When disposing of your appliance,
please choose an authorised disposal site.
Installation of your wine cabinet
•Place your wine cabinet on a floor that is strong enough to support it when it is fully loaded.
To level your wine cabinet, adjust the front levelling leg at the bottom of the cabinet.
•Locate the wine cabinet away from direct sunlight and sources of heat (stove, heater, radiator,
etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Extreme cold ambient temperatures may also cause the unit not to perform
properly.
•Avoid locating the unit in moist areas.
•Plug the wine cabinet into an exclusive, properly installed-grounded wall outlet. Do not under
any circumstances cut or remove the third (ground) pin from the plug. Any questions
concerning power and/or grounding should be directed toward a certified electrician or an
authorised Caple service centre.
Attention
•Store wine in sealed bottles
•Do not overload the cabinet
•Do not open the door unless necessary
•Do not cover shelves with aluminium foil or any other shelf material which may prevent air
circulation
•Should the wine cabinet be stored without use for long periods it is suggested, after a careful
cleaning, to leave the door ajar to allow air to circulate inside the cabinet in order to avoid
possible formations of condensation, mould or odours.
4

Operating your wine cabinet and setting the temperature
Please use the cabinet under a ambient temperature of 5-32 ºC, if the ambient temperature is
higher than or lower than this temperature, it will cause the temperature to fluctuate in the
cabinet and may prevent it reaching 5-18 ºC.
Control Panel
z“Light” Button
Switches the interior light ON/OFF
z“Run”
The indicator light illuminates to signify the cooling mode is currently in operation.
z“Power” Button
Switches the appliance on/off. ( press and hold this buttons for approximately 3 seconds);
z“Set Upper” Button
Is used to set the temperature in the upper compartment, the temperature setting can be
adjusted from 5 ºC to 10 ºC. When pressing this button, the system will enter the set up mode in
the upper compartment automatically. The LED will flash and the display will show the
temperature. Each press of the button will decrease the temperature by 1ºC. When exceeding the
minimum value that can be established, it will jump to the highest adjustable temperature
automatically. After you stop pressing the button for 5 seconds the LED figure will stop flashing.
z“Set Lower” Button
Is used to set the temperature in the lower compartment, the temperature setting can be adjusted
from 10 ºC to 18 ºC. When pressing this button, the system will be enter the set up mode for the
lower compartment automatically. Setting details are the same as above.
z“Upper”
Displays the temperature for the upper compartment.
z“Lower”
Displays the temperature for the lower compartment.
zAfter the unit is unplugged, the system will return to the factory set temperature. The
temperatures are as below:
Upper compartment: 6 ºC
Lower compartment: 12 ºC
zTo view the actual temperature at anytime press and hold the temperature adjustment button
(Set Upper or Set Lower) for approximately 5 seconds, the actual temperature will temporarily
flash in the LED display for 5 Seconds. After this it will revert back to the set temperature.
Flashing LED = Cabinet temperature
Steady LED = Set temperature
5

Note
•If the unit is unplugged, power is lost, or turned off you must wait 3 to 5 minutes before restarting
the unit. If you attempt to restart before this time delay, the wine cabinet will not start.
•When you use the wine cabinet for the first time or restart the cabinet after having been shut off
for a long time, there could be a few degrees variance between the temperature you select and
the one indicated on the LED readout. This is normal and it is due to the length of the activation
time. Once the wine cabinet is running for a few hours everything will be back to normal.
Using the shelves
•To prevent damaging the door gasket, make sure you have the door opened fully when pulling
shelves out of the rail compartment.
•For easy access to the storage content, you must pull the shelves approximately 1/3 out of the rail
compartment, however this unit was designed with a notch on each sides of the shelf tracks to
prevent bottles from falling.
Removing or installing shelves
•When removing any of the shelves out from rail compartment, tilt the shelf as per the diagram and
simply pull out, or when installing push the shelf in until it sits on the support brackets securely.
6

How to change the door opening
This appliance has reversible doors, but is delivered with a right hinged door. The left hand hinge kit
comes with the unit (in the box), should you wish to reverse the hinge on your unit please follow the
below directions.
1. Lower hinge (Right) 2 . Screws 3 .Door axis
4. Door 5. Top hinge (Right) 6. Hinge Screws
7. Top hinge (Left) 8. Decorative nail 9. Lower hinge (Left)
10. Door limit device 11. Screw
1. Open the door to a 90 degree angle, take out the 2 screws (2) from lower door axis (3), remove
the door (4) and the axis plate (3) from the door, (Fig. A).
2. Unscrew the screw (11) located underneath the door frame and the limit device (10), and relocate
it at the left end side of the door frame. (Fig. A/B)
3. Take out the 3 hinge screws (6) from the top right hinge (5) and remove it. (Fig. C)
4. Remove the decorative nails (8) from the top left of the cabinet and install the spare top hinge
(Left) (7) at top left of the cabinet with 3 screws. (Fig. D)
5. Following the above procedure, install the spare lower hinge to the left (9). (Fig. E)
6. Install the door once correctly aligned.
7. Insert the plastic decorative nails to cover the holes (8).
7

Fitting a kitchen plinth
This model is recessed to fit a kitchen plinth. A H55mm vent slot is required in the plinth to ensure air
is able to ventilate the appliance correctly, please see the below diagram
. Failure to include this vent
slot will invalidate the guarantee. Alternatively a Caple GRILL/SENSE600 stainless steel plinth grill can
be installed.
Installation diagram
8

Care and maintenance
Cleaning your wine cabinet
•Turn off the power, unplug the appliance, and remove all items including shelves and rack.
•Wash the inside surfaces with a warm water and baking soda solution. The solution should be
about 2 tablespoons of baking soda to 2 pints of water.
•Wash the shelves with a mild detergent solution.
•Wring excess water out of the sponge or cloth when cleaning area of the controls, or any
electrical parts.
•Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry
with a clean soft cloth.
Power failure
•Most power failures are corrected within a few hours and should not affect the temperature of
your appliance if you minimise the number of times the door is opened. If the power is going to be
off for a longer period of time, you need to take the proper steps to protect your contents.
Vacation time
•Short vacations: Leave the wine cabinet operating during vacations of less than three weeks.
•Long vacations: If the appliance will not be used for several months, remove all items and turn off
the appliance. Clean and dry the interior thoroughly to prevent odour and mould growth, leave
the door open slightly, blocking it open if necessary.
Moving your wine cabinet
•Remove all items.
•Securely tape down all loose items (shelves) inside your appliance.
•Wind the adjustable legs up to the base to avoid damage.
•Tape the door shut.
•Be sure the appliance stays secure in the upright position during transportation. Also protect
outside of appliance with a blanket, or similar item.
Energy saving tips
•The wine cabinet should be located in the coolest area of the room, away from heat producing
appliances, and out of the direct sunlight.
9

Problems with your wine cabinet
You can solve many common wine cabinet problems easily, saving you the cost of a possible service
call. Try the suggestions below to see if you can solve the problem before calling Caple Service.
Troubleshooting Guide
Problem Possible Cause
The wine cabinet does not operate. Not plugged in.
The appliance is turned off.
The circuit breaker tripped or a blown fuse.
The wine cabinet is not cold enough. Check the temperature control setting.
External environment may require a higher
setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
The compressor turns on and off frequently.
The room temperature is hotter than normal.
A large amount of contents has been added to
the wine cabinet.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work. Not plugged in.
The circuit breaker tripped or a blown fuse.
The bulb has burned out.
The light button is “OFF”.
Vibrations. Check to ensure that the wine cabinet is level.
The wine cabinet seems to make too much
noise.
The rattling noise may come from the flow of
the refrigerant, which is normal.
As each cycle ends, you may hear gurgling
sounds caused by the flow of refrigerant in
your wine cabinet.
Contraction and expansion of the inside walls
may cause popping and crackling noises.
The wine cabinet is not level.
The door will not close properly. The wine cabinet is not level.
The door was reversed and not properly
installed.
The gasket is dirty.
The shelves are out of position.
Caple Service contact details
If after using the Troubleshooting Guide you have been unable to solve the problem, please contact
Caple Service by telephoning 0844 800 3830 or alternatively email se[email protected].
10

Defrosting/condensation
Your wine cabinet is designed with an “Auto-cycle” defrost system. When the RUN cycle is OFF, the
refrigerated surface of the wine cabinet (interior rear wall) defrosts automatically. The defrosted water
is channelled into a drain pan which is located at the back of the cabinet next to the compressor from
where it evaporates.
Humidity system
The wine cabinet is equipped with a system for maintaining the correct level of humidity. If humidity is
too low, insert the small plastic reservoir on to the top shelf. Fill this reservoir 3/4 full with water.
Check the water level occasionally and refill as necessary.
Recommended storage temperatures
For storing ALL TYPES OF WINES 12 oc to 14 oc
Recommended drinking temperatures
Champagne NV, Sparkling 6 oc
Champagne Vintage 10 oc
Dry White Semillon, Sauvignon Blanc 8 oc
Dry White Gewürztraminer, Riesling 10 oc
Dry White Chardonnay 10 oc
Vintage Chardonnay 14 oc
Sweet White Sauternes Monbazillac, Late Harvest ice wine 10 oc
Sweet whites vintage Sauternes 14 oc
Beaujolais 13
oc
Red Pinot Noir 16 oc
VintagePinotNoirred 18
oc
Red Cabernet, Merlot, French, Australian, New Zealand, Chilean,
Argentinean, Italian, Spanish, Californian 18 oc
Red Grenache, Syrah 16 oc
11

Caple
Fourth Way
Avonmouth
Bristol
BS11 8DW
www.caple.co.uk