Carrier 30GTN User manual

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
PC 903 Catalog No. 533-076 Printed in U.S.A. Form 30GTN-3SI Pg 1 6-99 Replaces: New
Book 2
Tab 5c
Installation Instructions
Part Number 30GT-911---060
CONTENTS
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . 1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Install Harness and Make Wire
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Configure Control (All Sizes). . . . . . . . . . . . . . . . . . 7
Temperature Reset (4 to 20 mA). . . . . . . . . . . . . . . 8
Demand Limit (4 to 20 mA) . . . . . . . . . . . . . . . . . . . . 9
Demand Limit (Switch Controlled) . . . . . . . . . . . 10
SAFETY CONSIDERATIONS
Installation of this accessory can be hazardous due to sys-
tem pressures, electrical components, and equipment location
(such as a roof or elevated structure).
Only trained, qualified installers and service technicians
should install, start up, and service this equipment (Fig. 1).
When installing this accessory, observe precautions in the
literature, labels attached to the equipment, and any other
safety precautions that apply.
• Follow all safety codes.
• Wear safety glasses and work gloves.
• Use care in handling and installing this accessory.
INTRODUCTION
The Energy Management Module Accessory (EMM) pack-
age is required for additional Temperature Reset, Demand
Limit, and Ice Done features of the ComfortLink™
30GTN,GTR and 30GUN,GUR chillers. Temperature Reset
function by return water, outside air or space temperature do
NOT require the addition of this accessory. The following ad-
ditional features are supported by this accessory:
• temperature reset by 4 to 20 mA field supplied signal.
• demand limit control via field supplied two-step switch
input.
• demand limit control via field supplied 4 to 20 mA
signal.
• support of unoccupied operation for ice making through
field supplied contacts.
Accessory Package Contents
INSTALLATION
1. Inspect the package contents for missing or damaged
parts. File a claim with shipping agency if parts are
damaged. Notify your Carrier representative if any
items are missing.
2. Open and tag all electrical disconnects.
3. Open the left side control box door to access the con-
trol wiring side of box.
4. Using the five no. 6 screws provided in the package,
mount the EMM in the pre-drilled holes in the control
panel near the lower left corner of the display/fuse
bracket. See Fig. 2. Using the two no. 10 screws pro-
vided in the package, mount the terminal block above
the EMM board.
5. For size 130-210 machines (and modules 230A-420A,
330B-420B), mount the EMM board above TB5. See
Fig. 3.
6. The board addresses are set through 4-position DIP
switches. All switches are set to ON for all boards. See
Fig. 1.
Install Harness and Make Wire Connec-
tions — Locate harness supplied with accessory. use the
30GT415088 harness for 040-110 sizes (and modules 230B-
315B). Use the 30GT415224 harness for 130-210 sizes (and
modules 230A-420A and 330B-420B).
Make four plug connections at the EMM using the connec-
tors labeled EMM-J1, J4, J6, and J7. See Fig. 4 and 5.
Two remaining plug connections need to be made. Connect
the plug labeled 30GT415224 at the Main Base Board (MBB)
for all 040-110 sizes. Connect the plug labeled EXV-J3/MBB-
J3 at the Expansion Valve Board (EXV), if installed for 040-
110 sizes. Otherwise, connect the plug to the Main Base Board
(MBB). See Fig. 4.
For sizes 130-210 connect the plug labeled MBB-J2/
CXB-J2 to the Main Base board (MBB) or to the Expansion
Board (CXB, if installed) and connect the plug labeled EXV-J3
CXB-J3 at the Expansion Board (CXB, if installed). Other-
wise, connect the plug to the Expansion Valve Board (EXV).
See Fig. 5.
ELECTRIC SHOCK HAZARD.
To avoid the possibility of electrical shock,
open and tag all disconnects before installing
this equipment.
ITEM QUANTITY
Energy Management Module,
30GT515218 1
Terminal Block, HY84FE029 1
Screws, no. 6 3/4-in. long 5
Screws, no. 10 3/4-in. long 2
Harness Assembly, 30GT415088 1
Harness Assembly, 30GT415224 1
30GTN,GTR,GUN,GUR040-420
Energy Management Module (EMM)
Accessory
50/60 Hz

2
CEBD430351-0396-01C
TEST 1
CEPL130351-01
PWR
TEST 2
J1 J2
J4 J3
J5
J6 J7
LEN
STATUS
RED LED - STATUS GREEN LED -
LEN (LOCAL EQUIPMENT NETWORK) ADDRESS
DIP SWITCHES
Fig. 1 — EMM Board

3
LEGEND
CCN — Carrier Comfort Network
CHT — Cooler Heater Thermostat
CLHR — Cooler Heater Relay
CPSC — Compressor Protection and Control System
CXB — Expansion Board Accessory
EMM — Energy Management Module
EQUIP GND — Equipment Ground
EXV — Electronic Expansion Valve
FB — Fuse Block
FIOP — Factory-Installed Option
LED — Light-Emitting Diode
LEN — Local Equipment Network
LLSV — Liquid Line Solenoid Valve
NEC — National Electrical Code
TB — Terminal Block
TDR — Time-Delay Relay
TXV — Thermostatic Expansion Valve
Fig. 2 — Mounting EMM Module and Terminal Block, 040-110 and 230B-315B Sizes

4
Fig. 3 — Mounting EMM Module and Terminal Block, 130-210, 230A-420A and 330B-420B Sizes
LEGEND
CGF — Compressor Ground Fault
CHT — Cooler Heater Thermostat
CLHR — Cooler Heater Relay
CR — Control Relay
CXB — Expansion Board Accessory
EMM — Energy Management Module
EQUIP GND — Ground
EXV — Electronic Expansion Valve
FB — Fuse Block
FIOP — Factory-Installed Option
LED — Light-Emitting Diode
TB — Terminal Block
TRAN — Transformer

5
LEGEND
Fig. 4 — Making Wiring Connections for 040-110 Unit Sizes
CB — Circuit Breaker EXV — Electronic Expansion Valve SPT — Space Temperature
CKT — Circuit FIOP — Factory-Installed Option SW — Switch
CPCS — Compressor Protection Control Systems GND — Ground TB — Terminal Block
CWFS — Chilled Water Flow Switch MBB — Main Base Board TEMP — Temperature
CWP — Chilled Water Pump OAT — Outdoor-Air Temperature TRAN — Transformer
CXB — Expansion Board OPS — Oil Pressure Switch UL — Unloader
EMM — Energy Management Module PL — Plug

6
LEGEND
Fig. 5 — Making Wiring Connections for 130-210 Unit Sizes
CB — Circuit Breaker EXV — Electronic Expansion Valve SPT — Space Temperature
CKT — Circuit FIOP — Factory-Installed Option SW — Switch
CPCS — Compressor Protection Control Systems GND — Ground TB — Terminal Block
CWFS — Chilled Water Flow Switch MBB — Main Base Board TEMP — Temperature
CWP — Chilled Water Pump OAT — Outdoor-Air Temperature TRAN — Transformer
CXB — Expansion Board OPS — Oil Pressure Switch UL — Unloader
EMM — Energy Management Module PL — Plug

7
Configure Control (All Sizes)
1. The control must be configured to recognize the
Energy Management Module. Using the display, press
until the screen is blank. Use the arrow keys to
select the Configuration mode LED. Follow the steps
outlined in Table 1 using the keys on the display.
2. To change the value of EMM, press until the
Marquee display screen is blank. Use the arrow keys to
light up the Configuration mode LED. Press .
Press the down arrow key until OPT1 is displayed.
Press . Press the up arrow key to select
EMM. Press to stop display at its current
value, NO. Press again and PASS WORD
will be displayed. Press to bring up the
default password of 1111. Press four times to
confirm the password. Use the arrow keys as needed if
the password is other than 1111. The NO value will
now be flashing. Press the up arrow key to change
the value to YES and to accept the change.
Table 1 — Configuration Mode Menu
ESCAPE
ESCAPE
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
MODE
(RED LED) KEYPAD ENTRY SUBMODE KEYPAD ENTRY ITEM DISPLAY ITEM EXPANSION COMMENTS
CONFIGURATION DISP
UNIT
OPT1 FLUD X COOLER FLUID
HGB.S YES/NO HOT GAS BYPASS
SELECT
HPCM X HEAD PRESS.
CONT. METHOD
HPCT X HEAD PRESS.
CONTROL TYPE
PRTS YES/NO PRESSURE
TRANSDUCERS
PMP.1 ON/OFF COOLER PUMP
INTERLOCK
CPC ON/OFF COOLER PUMP
CONTROL
CA.UN X NO. CIRCUIT A
UNLOADERS
CB.UN X NO. CIRCUIT B
UNLOADERS
EMM YES/NO EMM MODULE
INSTALLED Default: No Change to Yes
ENTER
ENTER

8
Temperature Reset (4 to 20 mA) — A field sup-
plied and generated, externally powered 4 to 20 mA signal can
be used to provide leaving fluid temperature reset. The signal
must be connected to TB6. Connect the signal to TB6-2/5
(positive/negative). This is a simple linear function which re-
quires only two configuration changes. Follow the steps out-
lined in Table 2 to enable the function and configure the reset
temperature at 10º F for the 20 mA signal.
The configuration is now complete. As an example, if the
cooling set point (CSP.1) is set to 44 F, the control will linearly
reset the control point (CTPT) based on the 4 to 20 mA signal.
There will be no reset for a 4 mA signal. If the reset signal was
20 mA, the CTPT would be changed to 54 F. Similarly, a
12 mA reset signal would reset CTPT to 49 F. The actual 4 to
20 mA reset signal seen by the control can be viewed by ac-
cessing the item RSET, located under the Inputs mode, sub-
mode 4-20.
Table 2 — Menu Configuration of Temperature Reset Mode
MODE
(RED LED) KEYPAD ENTRY SUBMODE KEYPAD ENTRY ITEM DISPLAY ITEM EXPANSION COMMENTS
CONFIGURATION DISP
UNIT
OPT1
OPT2
RSET CRST 0 COOLING
RESET TYPE
0 SCROLLING STOPS
0 FLASHING ‘0’
1 SELECT ‘1’
1 CHANGE ACCEPTED
CRST 1 COOLING
RESET TYPE ITEM/VALUE/UNITS SCROLLING RETURNS
CRT1 125
CRT2 0
DGRC 0 DEGREES
COOL RESET SET MAXIMUM
RESET AMOUNT
FOR 20 mA SIGNAL
0 SCROLLING STOPS
0 FLASHING ‘0’
10 SELECT ‘10’
10 CHANGE ACCEPTED
DGRC 10 ITEM/VALUE/UNITS
SCROLLING RETURNS
ENTER
ENTER
ENTER
ENTER
ENTER
ESCAPE
ENTER
ENTER
ENTER
ESCAPE

9
Demand Limit (4 to 20 mA) — A field-supplied and
generated externally powered 4 to 20 mA signal can be used to
provide leaving fluid temperature reset. The signal must be
connected to TB6. Connect the signal to TB6-1/5 (positive/
negative). This is a simple linear function which requires only
two configuration changes. Follow the steps outlined in Table 3
to enable the function and configure a demand limit of 60% for
the 20 mA signal.
The configuration is now complete. There will be no de-
mand limit for a 4 mA signal. If the signal was 20 mA, the
chiller capacity (CAP) would be limited to 60%. Similarly, a
12 mA demand limit signal would limit chiller capacity to
80%. The actual 4 to 20 mA demand limit signal seen by the
control can be viewed by accessing the item DMND, located
under the Inputs mode, submode 4-20.
Table 3 — Menu Configuration of Demand Limit Mode
MODE
(RED LED) KEYPAD ENTRY SUBMODE KEYPAD ENTRY ITEM DISPLAY ITEM EXPANSION COMMENTS
CONFIGURATION DISP
UNIT
OPT1
OPT2
RSET CRST 0
CRT1 125
CRT2 0
DGRC 0
DMDC 0 DEMAND LIMIT
SELECT
0SCROLLING
STOPS
0 FLASHING ‘0’
2 SELECT ‘2’
2CHANGE
ACCEPTED
DMDC 2 DEMAND LIMIT
SELECT ITEM/VALUE/UNITS SCROLLING RETURNS
DM20 100 DEMAND LIMIT AT
20 MA
100 SCROLLING
STOPS
100 FLASHING ‘100’
60 SELECT ‘60’
60 CHANGE
ACCEPTED
DM20 60 DEMAND LIMIT AT
20 MA ITEM/VALUE/UNITS SCROLLING RETURNS
ENTER
ENTER
ENTER
ENTER
ENTER
ESCAPE
ENTER
ENTER
ENTER
ESCAPE

10
Demand Limit (Switch Controlled) — A field-sup-
plied pair of dry contacts can be used to provide one or two
steps of demand limit. The dry contacts must be connected to
TB6. Connect the contacts for Demand limit step one to
TB6-12, 13. Connect the contacts for Demand Limit step two
to TB6-14, 15. This is a step function which will limit the over-
all chiller capacity to pre-configured percentages when the
switch contacts close. Follow the steps outlined in Table 4 to
enable the function and configure a demand limit of 70% for
step one and 40% for step two.
The configuration is now complete. The overall chiller ca-
pacity (CAP, under the Run Status mode, submode VIEW) will
now be reduced to 70% when Demand Limit switch 1 is
closed. The capacity will be further reduced to 40% when De-
mand Limit switch 2 is closed. The actual demand limit switch
inputs seen by the control can be viewed by accessing the items
DLS1 and DLS2, located under the Inputs mode, submode
GEN.I.
Table 4 — Menu Configuration of Demand Limit Mode (Switch Controlled)
MODE
(RED LED) KEYPAD ENTRY SUBMODE KEYPAD ENTRY ITEM DISPLAY ITEM EXPANSION COMMENTS
CONFIGURATION DISP
UNIT
OPT1
OPT2
RSET CRST 0
CRT1 125
CRT2 0
DGRC 0
DMDC 0 DEMAND LIMIT
SELECT
0 SCROLLING STOPS
0 FLASHING ‘0’
1SELECT‘1’
1 CHANGE ACCEPTED
DMDC 1 DEMAND LIMIT
SELECT ITEM/VALUE/UNITS SCROLLING RETURNS
DM20 100
SHNM 0
SHDL 0
SHTM 60
DLS1 80 DEMAND LIMIT
SWITCH 1
80 SCROLLING STOPS
80 FLASHING ‘80’
70 SELECT ‘70’
70 CHANGE ACCEPTED
DLS1 70 DEMAND LIMIT
SWITCH 1 ITEM/VALUE/UNITS SCROLLING RETURNS
DLS2 50 DEMAND LIMIT
SWITCH 2
50 SCROLLING STOPS
50 FLASHING ‘50’
40 SELECT ‘40’
40 CHANGE ACCEPTED
DLS2 40 DEMAND LIMIT
SWITCH 2 ITEM/VALUE/UNITS SCROLLING RETURNS
ENTER
ENTER
ENTER
ENTER
ENTER
ESCAPE
ENTER
ENTER
ENTER
ESCAPE
ENTER
ENTER
ENTER
ESCAPE

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
PC 903 Catalog No. 533-076 Printed in U.S.A. Form 30GTN-3SI Pg 12 6-99 Replaces: New
Book 2
Tab 5c
Copyright 1999 Carrier Corporation