Carrier OSK102 User manual

Wi-FiKITUSERMANUAL
CA001U-APP(G3)
16122000A26161
20160216
Carrierwillnotbeliableforanyissues
andproblemscausedbyInternet,Wi-Fi
RouterandSmartmobile.Pleasecontact
theoriginalprovidertogetfurtherhelp.
NOTE:

CONTENTS
Model: OSK102
Standard: IEEE 802.11b/g/n
Antenna Type: External omnidirectionalAntenna
Frequency:Wi-Fi 2.4G
Maximum TransmittedPower: 15dBm Max
Dimension:55x24x8(mm)
OOO O
Operation Temperature:0 C~45 C/32 F~113 F.
Operation Humidity:10%~85%
Power Input: DC 5V/300mA
Applicable system :iOS,Android.
(Suggest: iOS 7.0 or later Android4.0 or later)
Please check theservice website formore
applicable devices.
Disclaimer: Due tothe special situationexisted
during Appuse, we explicitlyclaim as bellow:
Not all ofthe Androidand iOS systems are compatible
with theAPP.We will notbe responsible forany issue
as a resultof the incompatibility
SMART KITwireless safety strategy.
Smart kit onlysupport WPA-PSK/WPA2-PSK
encryption and noneencryption .
WPA-PSK/WPA2-PSK encryption isrecommended.
Hereby, wedeclare that this AC is in compliance
with the essentialrequirements and otherrelevant
provisions of Directive1999/5/EC. The declaration
of conformity maybe consulted withsales agent.
DECLARATION OF CONFORMITY
1
2
3
SPECIFICATION
PRECAUTIONS
1
DECLARATION OFCONFORMITY.........................1
SPECIFICATION...................................................1
PRECAUTIONS ....................................................1
INSTALLATION............. .......................................2
CONFIGURATION............... .................................4
APP OPERATION. ..............................................15
2
3
4
5
6
1
CAUTIONS
This device complies with Part 15 of the FCC Rules
and RSS 210 of Industry & Science Canada. Operation
is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Only operate the device in accordance with the
instructions supplied. This device complies with FCC
and IC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the
possibility of exceeding the FCC and IC radio frequency
exposure limits, human proximity to the antenna shall
not be less than 20cm (8 inches) during normal operation.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate the equipment.

1. Internet work
Wi-Fi router,smart mobile, smartair conditioner are
needed for thisfunction.
1 Smart Phone
2Smart Air conditioner
3 Wi-Fi Router
¢Ü
INSTALLATION
4
23
2. Smart kitinstallation
Remove the protectivecap of the smart kit
Open the frontpanel and insert the smart kit into
the Wi-Fi adapter.
Attach the QRcode packed with SMART KIT to the
side panel ofthe machine, ensure it is convenience
to be scannedby the mobile phohe.
1
2
3
Smart Phone cameraneeds to be 5 million pixels or
above to makesure scan QR code well.
Due to differentnetwork situation, sometimes, request
time-out could behappened, thus, it is necessary to
do network configurationagain.
Due to differentnetwork sitiuation, sometimes, control
process may returntime out. If this situation occurs,
do not feelconfused, the display on board and APP
may not bethe same.
2
2
2
1
3
Iphone:
Scan QR Codeor go to App Store and search for
Carrier air conditioner app and downloadit.
Android system:
Scan QR Codeor go toGoogle play,search for
Carrier air conditioner app and downloadit.
3. APP installation
''
1
2
s
m
a
r
t
k
i
t
Insert

CONFIGURATION
5
45
12
Click "CreateAccount " Enter an availableemail
address and createa
password, then click
Registration.
Note: The passwordis
only for thisAPP, not for
email system.
1.User Registrationon APP
Please ensure themobile device has connected to
Wi-Fi router.And the router has alreadyconnected to
internet before registrationand network configuration.
CAUTION:
It is better to log in email box and active registration
account by clicking link in case forget the password.
Make sure the mobile connect to the Wi-Fi network.
Make sure the mobile Wi-Fi function works well and
can be connected to Wi-Fi network automatically.
If the smart kit failed to connect to the router, please
confirm the encryption setting of router should be WPA
2. Set Air conditioner into AP mode
Turn onthe air conditioner, press the LED button
on the remotecontroller for 7times continuously.
When the displayshow AP and flash, itmeans
that the smartkit has alreadyentered the Wi-Fi
network setting mode.
Kindly reminder:
When the airconditioner entered intoWi-Fi network
setting mode, theremote controller cannot control
the ACbefore the Wi-Finetwork setting finished.
If there isno setting operationunder Wi-Fi network
setting mode, theair conditioner willquit this mode
automatically 8 minuteslater ,then theuser can
control theAC with remotecontroller normally.
1
2
AP

6 7
Network configuration forAndroid systemmobile
1Press "+Add Device"
34Configuration Success,
then the devicecan be
seen on thelist.
Home
User name
+
Add Device
My Home
Password
Cisco
Belkin
Air conditioner want to use your WiFi
Network OK Home
+
AC684E
Add Device
User name
Online
3. Add device to the account
Note: The configurationprocess is differentfor
Android system andiOS system mobile.
First, open theAPP, sign inwith the registered
account and password.
If the mobileis android system,please follow the
process as below, if themobile is Iphone, please go to
page 8 andfollow the process.
Select Wi-Fi network,
for example MyHome
,then enter theWi-Fi
password and clickOK.
2Select net_ac_xxxx
and click OK.
Net_ac_xxxx
Cisco
Belkin
Air conditioner want to use your WiFi
Network OK

8 9
Network configuration forIphone
1Press "+Add Device "
Home
+
Add Device
3
Read the instruction
above and pressthe
"Home" button toreturn
to the Iphonemain
interface.
Click mobile settingsto
enter the settingpage,
select WLAN setting.
4
20:14 61%
Settings
Airplane Mode
WLAN Smart
Bluetooth Off
Cellular Off
VPN
Notifications
Control Center
Do Not Disturb
General
User name
Choose net_ac_XXXX
Settings WLAN
CHOOSE A NET WORK.....
ASUS-5GX
ASUS-2.4GX
bdptest1
bdptest1-5G
HIWIFI-22EF60
net_ac_0010
20:14 61%
Xxxxxxxxx
Xxxxxxxxx
Xxxxxxxxx
Xxxxxxxxx
2

Type defultpassword:
12345678 and click
"Join "
Return to APP and
click Next
678
Joining "net_ac_0010"....
20:14 61%
Cancel Join
Enter Password
Password
10 11
Select Wi-Fi network,
for example MyHome
,then enter theWi-Fi
password and clickOK.
Home
User name
+
Add Device
AC684E
Online
Configuration Success,
the device canbe seen
on the list.
5

12 13
APP OPERATION
6
Please ensure bothmobile device andair
conditioner are connectedto the Internetbefore
using app tocontrol the airconditioner via internet,
please follow thenext steps:
12
Enter user account
and password, Click
"Sign in "
Select the targetair
conditioner to enter
the main control
interface.
Creat Accout
Forgot password?
[email protected]
Sign in
When finishing networkconfiguration, APPwill
display success cuewords on thescreen.
Due to differentInternet environment, itis possible
that the devicestatus still display offline" and can
not access tothe operation interface.
If this situationoccurs, user should
turn off theAC turn on it again.
pull the device
list down andrefresh the statusbecome "online",
If it doesnot work,
NOTE:
Home
User name
+
Add Device
AC684E
Online
AC684C
Online
AC684B
Online
1. Sign in

14 15
3Touchthe logo inthe
center to turnon the air
conditioner.
NOTE:
Not all thefunctions of theAPP areavailable for every
air conditioner.For example: ECOis only available for
inverter model, verticallouver swing isonly available
for the modelswith vertical swingmotor.
Now, theair conditioner
is available tobe
controlled byAPP.
4
Device Name
Setting
temperature
ON/OFF
Special
functions
Running mode
Fan speed
Mode selection Fan speed selection
Turbo
Page selection
Vertical louvers
swing
Horizontal louvers swing ECO mode
Celsius /
Fahrenheit
2. Main interfaceand functions

16 17
ON/OFF:
Press this buttonto turn on or turn offthe unit.
Mode selection:
Press this buttonto change the running mode
(COOL, HEAT, DRY, FAN,AUTO)
Fan speed selection:
Press this buttonto change the fan speed
High fan 3layer aura
Med fan 2layer aura
Low fan 1layer aura
Turbo: *
Press this buttonto active turbomode.
(Only available forcool running)
Vertical louversswing: *
Press this buttonto active thevertical louvers
swing.
Horizontal louvers swing:
Press this buttonto active thehorizontal louvers
swing.
ECO : *
Press this buttonto active ECOmode.
Celsius / Fahrenheit:
Press this buttonto change thetemperature unit
showing on theAC display.
Setting temperature:
Touchthe screen near the temperature, slip up &
down to changethe temperature, donot loosen
finger until thenumber reach to target.
* Model dependent
3. SPECIAL FUNCTIONS
Timer on/ Timer off
Weekly, user can make an appointment to turn on or
turn off theAC on specific time. User can choose
circulation to keepthe ACunder schedule control
every week.
O
Including: Timeron, Timeroff, 8 C Heat, Sleep,
Check.
NOTE: The smart kitwill check thesoftware program
in the airconditioner control parts,only show the
available functions onthe APP.
1Choose Timeron or
Timer off

18 19
2Choose the settingtime
to turn onor turn offthe
air conditioner.
3Choose the date,then
confirm with OK ."
Sleep
This function cancustomize comfortable sleep
by setting targettemperature.
Edit
Young
Elder
Children
1Choose sleep function. 2Choose Edit, Young,
Elder or Childrenmode.
In Edit mode,user can
choose the setting
temperature within 8
hours.
Finally confirm with
OK"

20 21
Check
This function cansimply check theAC runningstatus.
When finishing thisprocedure, it canshow the
normal items, abnormalitems, and detailinformation.
1Choose check function. 2The air conditioner scan
the running status.
Testing 97
97
Normal
0
Abonormal
3Finish check. 4Press Done
", theAPP
will show thedetail.

22 23
O
8 CHeat
O
In this mode,the air conditionerwill run under8 C
Heat. When peoplego outside, thisfunction can
protect the furniturefrom frost damage.
4. Change theinformation of device
User can modifytheir information andnominate
the name forthe devices.
1Press the picture.
Modify user information
2Choose the information
need to bechanged,
then press Save .

24 25
1Press the settinglogo
Nominate the device
2Nominate the device,
then press Save .
Note: TheAPP may updatethe user interface
without notice.