Carrier RG10L1/BGEF User manual

REMOTE CONTROLLER
OWNER’S MANUAL
16117000002881
CA14R-RG10L1(U2HS)
2022.12.02

02
01
Correct Disposal of Battery
- This marking printed in the batteries attached to your Air Conditioning product is information for end-uses .
- Batteries, at their end-of-life, should be disposed of separately from general household waste. Please,
dispose of batteries correctly at your local community waste collection or the recycling center.
CAUTION
CONTENT
1. QUICK START
1. QUICK START
2. DISPLAY AND BUTTONS
2.1 Display
2.2 Buttons
3. HOW TO USE BASIC FUNCTIONS
3.1 Basic Operations
3.2 Timer Function
4. HOW TO USE ADVANCED FUNCTIONS
FIT BATTERIES
POINT REMOTE TOWARD UNIT
PRESS POWER BUTTON
SELECT MODE SELECT TEMPERATURE
SELECT FAN SPEED
1
6
2
5
3
4
AUTO
LOW
MED
HIGH
MODEL:
RG10L1(U2HS)/BGEF
RG10L1(U2HS)/BGCEF
2
3
3
4
5
5
6
7
The remote control uses two alkaline batteries (1.5 Volts).
Do not use old batteries or batteries of different types, as this may cause the controller malfunction.
The average battery life during normal use is approximately half a year.
Replace the batteries when there is no receiving beep coming from the indoor unit or transmission
indicator on the remote control fails to light.
If you do not use the remote control for more than two months, please remove the batteries.
Otherwise battery leakage may damage the remote control.
The maximum operating distance for the remote control is approximately 8 meters.
Avoid direct sunlight on the receiver of indoor unit, which may interfere with good signal reception
and the air conditioner may not work properly. Draw the curtains to avoid direct sunlight.
Keep the remote control away from water. Do not let the remote control fall down.
Never use objects with sharp point to press the button on the remote control.
Prevent any liquid from falling into the remote control.
If other electric applications react to the remote control, move these applications.
Do not dispose of batteries as unstored municipal waste. Refer to local laws for proper disposal of
batteries.
Avoid obstacles obstructions such as curtains, doors or other materials between the remote control
and the receiver of indoor unit to avoid blocking the signals from the remote control to the indoor unit.
The transmitter of remote control must be directed toward the receiver of indoor unit when pressing
the buttons of the desired functions. An acoustical acknowledgement sound (beep) will indicate that
signal has been received.
INSTRUCTIONS OF USING WIRELESS REMOTE CONTROL
Mode
My Mode Follow Me LED Turbo
Ioniser
Swing
Timer
SelfClean
Mode On/Off Fan
Sleep
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
SETTEMPERATURE

2. DISPLAY AND BUTTONS
04
03
NOTE: AUTO mode and HEAT mode are not available for Model RG10L1(U2HS)/BGCEF.
2.1 DISPLAY 2.2 BUTTONS
On/Off
Press to start operation.
Press again to stop.
Mode
Press the mode button to
switch the mode in turn.
Eco Gear
Press to enter the energy
efficient mode
LED
LOCK
Fan Speed
Press to select the desired fan speed.
Temperature UP
Increases temperature in
0.5 C /1 F increments.
Max. Temp. is 30 C/86 F .
Press to turn on/off the LED
display. Pressing 5 more
seconds to alternate the indoor
display between setting
temperature and room
temperature(Model dependent).
Decreases temperature in 0.5 C/1 F
increments. Min. Temp. is 16 C/60 F.
Temperature Down
Swing
NOTE: HEAT mode is not supported
by the cooling only appliance.
SET
Scrolls through operation
functions as follows:
The selected symbol will flash on
the display area, press the OK
button to confirm.
[*]: Model dependent
OK
Used to confirm the selected
functions.
TIMER
Set timer to turn unit on or off.
Humidity
Press together Turbo button and
Humidity button at the same time more
than 5 seconds to activate Lock
function.
Breeze away >Active clean>
Fresh/UV > Sleep> Follow Me
> AP mode
Starts and stops the horizontal louver
movement. Hold down for 2 seconds
to initiate vertical louver auto swing
feature(some units).
*
*
*
Eco Intelligent eye
Used to detect the people activities in
the room to save energy.
Adjust the room humidity during
Dry operation in a range of
35%~85%. Press this button to
increase the humidity in 5%
increments.
NOTE: After setting, the humidity
settings will display on the screen.
Turbo
Enables unit to reach preset
temperature in shortest possible
time.
NOTE: Press together &
buttons at the same time for 3 seconds
will alternate the temperature display
between the °C & °F.
Silence
LOW
MED
HIGH
AUTO
2%-20%
21%-40%
41%-60%
61%-80%
81%-100%
1%
Information are displayed when the remote controller is power up.
Transmission Indicator
MODE display
TIMER ON display
FAN SPEED display
TIMER OFF display
Silence feature
display
ECO display
GEAR display
LOCK display
Horizontal louver
swing display
Vertical louver auto
swing display
Turbo mode display
Not applicalbe for
this unit
Temperature/Timer/Fan speed
Humidity display
Active clean feature display
Fresh and UV(if any) feature display
Sleep mode display
Follow me feature display
Wireless control feature display
Low battery detection display(If flashes)
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual
operation, only the relative function signs are shown on the display window.
Displays when LOCK feature
is activated.
Silence
LOW
MED
HIGH
AUTO
Lights up when remote
sends signal to indoor unit
Displays selected fan speed:
Displays the current
including:
mode,
2%-20%
21%-40%
41%-60%
61%-80%
81%-100%
1%
This fan speed can not be
adjusted in AUTO or DRY
mode.
Displays when ECO
feature is activated
Displays when GEAR
feature is activated
Displays the set temperature
by default, or fan speed or
timer setting when using
TIMER ON/OFF functions.
Temperature range:
oo
16-30 C/60-86 F
Timer setting range:
0-24 hours
Fan speed setting range:
Humidity setting range:
AU -100%
35% -85%
This display is blank when
operating in FAN mode.
   
Breeze Away display
ECO intelligent eye display
Not applicable for this unit
Not applicable for this unit
Not applicable for this unit

3. HOW TO USE BASIC FUNCTIONS
3.2 TIMER FUNCTION
TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.
TIMER
ON
NOTE:
1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each
press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example,
press 5 times to get 2.5h, and press 21 times to get 11h,) The timer will revert to 0.0 after 24.
2. Cancel either function by setting its timer to 0.0h.
Point remote to unit and wait 1sec,
the TIMER ON will be activated.
TIMER
OFF
Press it for multiple times to set
the desired time to turn off the unit.
Point remote to unit and wait 1sec,
the TIMER OFF will be activated.
3.1 BASIC OPERATIONS
AUTO
Mode
Select AUTO mode Set your desired temperature
NOTE:
1. In AUTO mode for heat pump system, the air conditioner can automatically choose the mode of
Cool, Heat or Fan by sensing the difference between the actual room temperature and setting
temperature.
2. In AUTO mode for cooling only system, the air conditioner can automatically choose the mode of
Cool or Fan by sensing the difference between the actual room temperature and setting temperature.
3. In AUTO mode, fan speed can not be set.
Mode
Turn on the air conditioner
COOL
or
HEAT
Mode
Select COOL/HEAT mode Set the temperature Turn on the air conditioner
Set the fan speed
DRY
Mode
Select DRY mode Set the temperature
NOTE:
In DRY mode, fan speed can not be set since it has already been automatically controlled.
Turn on the air conditioner
FAN
Mode
Select FAN mode Turn on the air conditioner
Set the fan speed
Before operation, please ensure the unit is plugged in and power is available.
ATTENTION
Mode
Mode
Mode
06
05
ON/OFF
MODE
FAN
SHORT
CUT
TIMERON
TIMEROF
F
TEMP
SLEEP
ON/OFF
MODE
FAN
SHORT
CUT
TIMERON
TIMEROF
F
TEMP
SLEEP
Press TIMER button to initiate
the ON time sequence. Press Temp. up or down button for
for multiple times to set the desired
time to turn on the unit.
Press TIMER button to initiate
the OFF time sequence.
xn
xn
TIMER
TIMER

08
07
4. HOW TO USE ADVANCED FUNCTIONS
Setting TIMER ON & OFF (example).
Current
time 1PM
2:00PM 3:00PM 4PM 5PM 6PM
Timer starts Unit turns
ON
Unit turns
OFF
2.5 hours later
5 hours later
3:30PM
Example: If current timer is 1:00PM,
to set the timer as above steps, the
unit will turn on 2.5h later (3:30PM)
and turn off at 6:00PM.
Swing
Eco
Gear
Press Swing button when the unit is turned on.
Swing
ON/OFF
MODE
FAN
SHORT
CUT
TIMERON
TIMEROF
F
TEMP
SLEEP
ON/OFF
MODE
FAN
SHORT
CUT
TI
M
E
R
O
N
TIMEROF
F
TEMP
SLEEP
xn xn
xn
TIMER
TIMER
The horizontal louver will
swing up and down automatically
when pressing Swing button.
Press again to make it stop.
2s
Swing
Keep pressing this button more
than 2 seconds, the vertical louver
swing function is activated.
(Model dependent)
If continue to press the SWING button, five different airflow directions can be set(Model dependent). The louver can
be move at a certain range each time you press the button. Press the button until the direction you prefer is reached.
Press this button under COOL Mode to enter the energy efficient mode.
Note:This function is only available under COOL mode.
ECO operation:
GEAR operation:
Under cooling mode, press this button, the remote controller will adjust the temperature automatically to
24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the
set temperature is above 24 C/75 F, press this button, the fan speed will change to Auto, the set temperature
will remain unchanged.
Note:
Pressing the this button, or modifying the mode or adjusting the set temperature to less than 24 C/75 F will
stop ECO operation.
Under ECO operation, the set tmeperature should be 24 C/75 F or above, it may result in
insufficient cooling. If you feel uncomfortable, just press this button again to stop it.
Press the Eco/Gear button to enter the GEAR operation as following:
75%(up to 75% electrial energy consumption) 50%(up to 50% electrial energy consumption)
Previous setting mode.
Under GEAR operation, the display on the remote controller will alternage between electical
energy consumption and set temperature.
O
O O
O
O
O
O O
O
O
Press this button to enter the energy efficient mode in a sequence of
following:
ECO GEAR(75%) GEAR(50%) Previous setting mode ECO......
NOTE: When the unit is off, press and hold MODE and SWING buttons together for one second, the louver will open
for a certain angle, which makes it very convenient for cleaning. Press and hold MODE and SWING buttons together
for one second to reset the louver(some units only).

4. HOW TO USE ADVANCED FUNCTIONS
10
09
Keep pressing this button more than 5 seconds, the
indoor unit will display the actual room temperature.
Press more than 5 seconds again will revert back to
display the setting temperature(Model dependent).
LED
Press LED button
Press this button to turn
on and turn off the display
on the indoor unit.
LED
Press this button more than 5 seconds
Turbo
Press this button
Press this button to activate Turbo feature. It enables the unit to reach the set temperature in the shortest time.
Press it again to disable it.(Model dependent)
The unit will operate at
the biggest capacity
output to reach the
setting Temp. quickly.
LED
5s
SET
Turbo
ECO
Intell-
ignet
Eye
Press this button
or
SET SET OK
Press the SET button to enter the function setting, then press SET button or TEMP or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
FRESH/UV lamp function( ) (some units) :
AP function( )(some units) :
Follow me function( ) :
The FOLLOW ME function enables the remote control to measure the temperature at its current location
and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT
modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will
enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
When the FRESH function is initiated, both the Ionizer(if any) and UV lamp(if any) function are energized
and will help to remove pollen and impurities from the air.
If the memory feature is stopped, “ ” displays for 3 seconds on the screen.
OF
While the memory feature is activated, press the ON/OFF button, shift the mode or power failure
will not cancel the Follow me function.
NOTE: Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function.
If the memory feature is activated, “ ” displays for 3 seconds on the screen.
On
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing
the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.
Sleep function( ) (some units) :
The SLEEP function is used to decrease energy use while you sleep(and don’t need
the same temperature settings to stay comfortable). This function can only be activated
via remote control. For the details, see “Sleep operation” in “USER’S MANUAL”.
NOTE:
The SLEEP function is not available in FAN and DRY mode.
Under ECO Intelligent eye mode, with the built-in infrared sensor, the unit
can detect the people’s activities in the room. In Cooling/Heating mode ,when
you are away for 30 minutes, the unit automatically lowers the frequency to
save energy(for inverter models only). And the unit will automatically resume
operation if sensing human activity again.
Active clean function( ) (some units) :
The Active Clean Technology washes away dust, mold, and grease that may cause odors when it adheres
to the heat exchanger by automatically freezing and then rapidly thawing the frost.
When this function is turned on, the indoor unit display window appears “CL”, after 20 to 45 minutes, the unit
will turn off automatically and cancel CLEAN function.
This feature avoids direct air flow blowing on the body and makes you feel indulging in silky coolness.
NOTE: This feature is available under cool, Fan and Dry mode only.
Breeze Away function( ) (some units) :
Breeze away ( ) Active clean ( ) Fresh/UV ( ) Sleep( ) Follow Me( )
AP mode ( ) Breeze away....
[ ]: Model dependent




*
*
*
*

4. HOW TO USE ADVANCED FUNCTIONS
12 11
F. P.
Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F.
The unit will operate
at high fan speed (while
compressor on) with
temperature automatically
set to 8 C/46 F.
Press this button 2 times under HEAT Mode and setting temperature of 16 C/60 F to activate the freeze
protection function. It will help to keep the room above 0 C/32 F (freezing point) in severe cold winter.
Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.
Keep pressing Fan button for more than 2 seconds to activate/disable Silence function.
Note:This function is for heat pump air conditioner only.
Silence
Due to low frequency operation of compressor, it may result in insufficient cooling and heating capacity.
Press ON/OFF, Mode, Sleep button, turn on F.P.or Self clean function while operating will cancel silence
function.(Model dependent)
2
2s
Lock
Mode
Press together button and button at the same time more than 5 seconds to activate
At lock mode , all buttons will not response except pressing these two buttons for two seconds again to disable locking.
5s
Lock symbol displays
5s
Turbo
Humidity
Turbo
Humidity
NOTES FOR USING REMOTE CONTROL
The device could comply with the local national regulations.
In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void
user’s authority to operate the equipment.

图纸要求：
材质：双胶纸80g
尺寸：A3纸对折为A4,尺寸：210*290
封面封底双色套印，内页黑白。
封面套印开利蓝pantone 072 (C100, M85, Y0, K0)
此页无需印刷