Carson MicroFlip MP-250 User manual

MP-250
MicroFlip
™
100x–250x Zoom Pocket
Microscope
Adapter clip
Eyepiece
LED switch
Focusing ring
Install thebattery
1. Slide open the battery door (Fig.1).
2. Install 1 (one) AA alkaline battery with the correct polarity (Fig.2).
3. Attach the battery door (Fig.3).
Fig.1 Fig.2 Fig.3
Instructions for Use
UV light switch
Zooming dial
Battery door
Front Facing LED
Base plate
Objective lens
UV light
Downward
Facing LED

Using the microscope to view objects directly
1. Make sure the base plate sits behind the battery door in the upright position (Fig.4).
2. Press the LED switch to turn on the LED (Fig.5). Please note that when base plate is in upright position
only front facing LED will illuminate.
3. Place the viewing object directly below the objective lens (Fig.6).
Using the microscope to view specimen slides
Fig.10 Fig.12 Fig.11
Fig.4 Fig.5 Fig.6
Adjusting zoom & focus
1. Adjust the zooming dial tothe desired level
of magnification (Fig.10).
2. Rotate the focusing ring until the image is
sharp andclear (Fig.11).
WARNING:
Do not look directly
at the UV light.
Press and hold the UV light switch to activate the
UV light (Fig.12).
NOTE: The UV light is deactivated when the base
plate is flipped down to the base of the microscope.
1. Flip the base plate down so that it sits on the base of the microscope (Fig.7).
2. Press the LED switch to turn on the LED (Fig.8). Please note that when base plate is down only downward
facing LED will illuminate.
3. Insert the specimen slide into the slot between the objective lens and the base plate (Fig.9).
Fig.7Fig.8Fig.9
1.
UV light

If you experience any difficulties, please contact us and we will be happy to help you.
For warranty information, visit www.carson.com/warranty
In the U.S.A.
Phone: [phone]
Email: [e-mail]
In the U.K.
Phone: [phone]
Email: uk[email protected]
In the E.U.
Phone: [phone]
Email: [email protected]
MP-250 / © 2019
If there is more than one rear-facing camera, use the primary one. Typically, the primary is a 1x wide-
angle color camera, and the other camera(s) are secondary.
For Apple dual camera phones, the primary camera is the one closest to the corner. Use photo or video
mode only.
For Android, the primary camera can be determined by which does not show an image in your app
while blocking the individual camera.
For the latest instructions on multiple camera phones, please visit www.carson.com/multicam.
•Turn off the LED at the end of the observation by pressing the LED switch.
•Remove the battery before storing the microscope for an extended period.
•To avoid possible permanent eye damage, do not look at the sun or bright objects with the microscope, nor
place the lighted microscope directly upon human eye.
•The device may get warm after extended period of use. This is normal and should notbeconsidered asa defect.
•Inspect all batteries for signs of corrosion or leakage. Do not expose to fire or excessive heat. Use alkaline
batteries only, rechargeable batteries are not recommended.
WARNING:
Always hold the phone securely during use. If you release
the phone while it is attached to the microscope, it can fall
which may result in damage to the phone.
Using the adaptor clip
Fig.14
Align the camera of the
phone to the center of the
circular hole of the adapter
clip (Fig.13).
Fig.13
Attach the adapter clip to
the top of the microscope
as shown in Fig. 14 and
turn on camera. Refer to
page 2for procedures of
using the microscope.
If viewing image is not
centered or is not a
complete round image,
adjust adapter clip making
sure it is centered over
camera.
Fig.15
To maximize your image,
pinch screen to enlarge.
For best results, use in
video mode.
MULTIPLE-LENS CAMERA PHONE:
Storage & Safety
•
•
•
•