Casanoov RANGER C300 User manual

RANGER C300
INSTRUCTION MANUAL / NOTICE DE MONTAGE / MONTAGEANLEITUNG / MANUAL DE MONTAJE / MANUAL DE MONTAGEM / MANUALE DI MONTAGGIO / MONTAGEHANDLEIDING / INSTRUKCJA MONTAŻU
EN FR DE ES PT IT NL PL
STI-000025
STW-000025
EN
FR
DE
ES
PT
IT
NL
PL
The manual should be read prior to beginning installation and keep after
Le manuel doit être lu avant de commencer l’installation et conservé après
Das Handbuch sollte vor Beginn der Installation gelesen und nach der Installation aufbewahrt werden.
El manual debe ser leído antes de comenzar la instalación y mantenerlo después
O manual deve ser lido antes do início da instalação e mantido após
Il manuale deve essere letto prima di iniziare l’installazione e conservato dopo
De handleiding moet voor het begin van de installatie worden gelezen en na de installatie worden bewaard
Instrukcję należy przeczytać przed rozpoczęciem instalacji i zachować ją po
CAUTION / ATTENTION / ACHTUNG / ATENCIÓN / ATTENZIONE / AANDACHT / UWAGA
!

EN
FR
DE
ES
PT
IT
NL
PL
3
22
41
60
79
98
117
136
Manual translated from English version using automatic translator. In case of question please refer to english version.

EN
3
CAUTION
• This product must be installed by well-trained skilled personnel in compliance with the safety
regulations the field of residential and commercial sliding gate opener devices.
Unqualified personnel may damage the instruments and cause harm to the public.
• Electric Power must be disconnected prior to installation, or performing any maintenance.
• Please read the manual carefully before installation. Incorrect installation or misuse of product
may cause seriously damage to users and property.
• If the electric cable is damaged or broken, it must be replaced by a whole and properly insulated
wires, to avoid electric shock or any hazardous environments.
• Keep the wireless transmitters out of children reach.
• Do not allow children or other individuals to stand by the path of the motor arms or the path
of the gates while in operation.
• Do not use the remote wireless transmitters when the gates are out of sight.
• Do not install the products in corrosive, inflammable, and/or explosive environments.
• Avoid installing the motor arm where the override manual release key is exposed to the public.
!

EN
4
Tools Required
(Required) (Required) (Required) (Required)
(Required) (Required) (Required) (Recommended)
x1 x2 x2 x4 x2
A B C D E

EN
5
Serial Number

EN
6
Product overview
Technical specifications
Max gate weight : 300 KG
Environment Temperature : -25°C ~ +55°C
Protection Class : IP55
Open(close) speed : v=12m/min
Maximum pull : 1100N
Gross weight : 7 KG
Motor voltage : 230V - 250W
Input power : 220VAC±10%/110VAC±10%
Frequency : 50Hz/60Hz
Output gear module : M=4
Output gear number: Z=16
Output torque:30.0 N.m
Rated speed : 1400RPM
Working humidity : ≤85%

EN
7
Manual unlocking
Sliding Gate automation : Features & Options
ALARM LAMP
GATE MOTOR
PUSH BUTTON
TRANSMITTER
GEAR RACK
PHOTOCELL
Insert key, rotate 90° clockwise.
Releas arm in torsion. Wriggle 90°.
Gate ‘s motor will be in released.

EN
8
1. Stylish appearance design and built-in control panel integrated inside the mechanism, no external controller
or receiver needed.
2. Built in limit switch allowing the motor to switch off once the cycle is finished.
3. Built in manual override with 2 supplied unique override keys in case of emergency or power failure.
4. Pedestrian mode.
5. Condominium mode.
6. Resistance sensitivity and auto-closing delay time adjustable.
7. Stop/Reverse in case of obstruction during gate opening and closing.
8. Easy installation, firm and solid structure, stable and reliable driving, permanently lubricated, maintaining-free.
9.Single-phase self-lock, anti-pushing, anti-lifting ,safe and reliable.
General options and accessories
Construction Drill and Bolts
Install your motorisation on a concrete slab.
Screw the support plate in place using expansion bolts.

EN
9
Rack Fixing
Set the gear-motor on manual unlocking. Wide open the gate’s door.
Place the rack: place the first element on the pinion and fix it with screws to the gate.
Move the door manually and repeat the procedure with the other elements using adistance spacer to
ensure the correct position from the rack.
It is advisable to leave 2mm between the rack and the gear to avoid the gate resting on the gear-motor.

EN
10
OPENING TO THE RIGHT
OPENING TO THE RIGHT
Limit switch
Position : 1-2
Place the blue stop on the motor side to control the opening.
The red stop controls closing.
Blue wire on Com
Yellow wire to Open
Red wire on Close
1
2
3
Blue
Yellow
Red

EN
11
OPENING TO THE LEFT
OPENING TO THE LEFT
Limit switch
Position : 2-3
Place the red stop on the motor side to control opening.
The blue stop controls the closing.
Blue wire on Com
Red wire to Open
Yellow wire on Close
1
2
3
Blue
Yellow Red

EN
12
Control board setting

EN
13
Connection of the flashing light
Connection of infra-red photocells

EN
14
Connection of Push button and Videophone
Push button
Videophone

EN
15
Function testing
Terminal stop
detection
Power switch
Limit switch
option J1
Programming set-
ting
Learning button
Close sensitivity
adjusting
Open sensitivity
adjusting
Connect to start
capacitor
!

EN
16
7.1 / 7.2 Gate open and close - blocked detection
A. High sensitivity : when the motor is rotation, will meet some minor resistance, then control board will
send a signal to let motor stop rotating.
B. Low sensitivity : when the motor is rotation, will meet greater resistance, then control board will
send a signal to let motor stop rotating.
C. As picture show : when pointer rotate to black part, the control panel will quit this syste
7.3 Programming setting: 8 settings on the control board.
1: Optional limit modes.
OFF : NC mode (Factory setting)
ON : NO mode.
Limit-switch direction’s setting (J1):
Normal: Short circuit cap simultaneously No.1 and No.2 of J1 (Factory setting).
If motor system installed at left of gate. Please adjust the J1. Short the cap simultaneously No.2 and
No.3.
2: Infrared mode.
OFF: NC mode (Factory setting).
ON: NO mode.
If the gate meets obstacles during closing, it will auto-stop and auto open. After the gate complete
open it will auto-close again if the obstacle disappears within 2s, if not, it will not auto-close until to
the obstacle disappears.
3 & 4: Auto-close setting time.
The auto-close function activated after gate complete opens to its place and stop by limit switch:
• No° 3 &4, OFF-OFF: Auto close function disabled (Factory setting)
• No° 3 &4, ON-OFF: 10 S
• No° 3 &4, ON-ON: 60 S
• No° 3 &4, OFF-ON: 30 S
Close sentivity
adjusting
Open sentivity
adjusting
Programming
setting
7.1
7.2
7.3

EN
17
7.4 Learning remote-control codes:
- Control panel can memory more than 50 pcs remote controls.
- Code learning: Press board «LEARN» button. LED indicator
lights on.
- Press remote control first button. LED indicator flashes twice
= code learning succeed.
If no remote-control signals received within 2.6s, the receiver
will automatic quit learning functions.
- Code clearing: Press and hold the button 6 seconds. LED
indicator flashes twice = all the code that has been memorized
in control board will be cleared.
Learning button
Close sensitivity
adjusting
5&6: Auto-close setting time when pedestrian mode is activated.
When remote control triggers the pedestrian mode (remote control button 2 or 4), the gate will stop
after opening for 6s. If auto-close function activated, the gate will auto-close after gate open to 6s.
Auto-close time setting as follows:
• No° 5 &6, OFF-OFF: Auto close function disabled (Factory setting)
• No° 5 &6, ON-OFF: 5 S
• No° 5 &6, ON-ON: 30 S
• No° 5 &6, OFF-ON: 10 S
Note:
When the motor is running, the motor will stop immediately if triggers pedestrian mode.
After triggering the pedestrian mode to open the gate for 6s, no matter it enters the countdown to close
the gate or stop status. If trigger again, the gate will close the gate immediately.
7: Condominium mode setting.
OFF: Condominium mode disabled (factory setting).
ON: Condominium mode activated.
When the gate is opening it triggers remote control and the start interface are invalid until the door is
opened.
When the gate is closing it triggers remote control and the start interface. The gate will stop to close
and auto-open until the opening limit is reached. The remote control and the start interface are invalid
when the gate is opening.
8: Remote control buttons mode.
OFF: Single button control circularly.
First button controls gate open, stop, close, second button use for pedestrian mode.
ON: Three buttons control.
First button controls gate open, second button controls gate stop, third button controls gate close ,
fourth button used for pedestrian mode
Note: Please choose the remote-control’s mode firstly before remote control code clearning to control
board
7.4

EN
18
Connect to start
capacitor
Limit switch
option
Terminal stop
detection
Power switch
7.5 Motor-Start Capacitors:
Capacitors are connected with
control board. Before using the
motor, please confirmed the
interface of capacitors is secure.
7.6 Limited switch options (J1):
Limit switch is used to switch
terminal stop detection interface,
that direction of open and close
the gate.
7.7 Terminal stop detection
interface:
Terminal for limit switch, such as
spring limit or magnetic limit.
7.8 Power switch:
Switch on /off power stop when
doing some setting on the
control-board.
7.5
7.6
7.7
7.8

EN
19
Trouble Shooting
Problem Possible causes Repair method
Gate fails to operate. 1. Check the clutch states, power-driven state or not?
2. Power no indication, and power trip.
3. The fuse has broken
4. Remote control failure or invalid
5. Damaged power cable
6. Remote control or motor problem
> Recovery
> To restore power.
> Change the fuse.
> Detection or change.
> Detection and Repair.
> Detection and Repair.
Working distance of remote
control reduced.
1. Low battery power or damaged
2. Interference from equipment using the same fre-
quency
3. The receiver of controller was damaged
> Replace battery.
> Wait / eliminate interference.
> Replace the control board.
Gate fails to stop at start or
end position.
1.The terminal stop toggle switch is damaged or obs-
tructed.
2. Limit switch of the motor and the limit detec
tion of the interface PCB board plug off.
3. Limit of open and close is in wrong position.
> Replace toggle switch or remove
obstruction.
> Insert and fixed it.
> Adjust of limit switch(K1)
Press open and close key of
motor, but can’t working /
operate
1. Blocked sensitivity is too high(set too big)
2. The gate has lifted off the track and disengaged the
drive gear from the rack
> Make blocked sensitivity lowered
and check gear and racks can operate
normally.
> Maintenance and replace.
1. When someone or obstructions between the gate, do not open or close the door to ensure safety.
2. The power supply for the control board should be equipped with a separate switch
with a fuse rated at 10AMP.
3. There is strong electricity in the control box. Please cut off the power supply before opening the
cover.
4. Motor gear modulus M = 4, number of teeth = 16, use the corresponding racks.
5. the gate should be as straight as possible, making sure after racks fixed good and the gate can be
in a good position with motor gear.
6. Racks and gear should be controlled in good gap. so can make sliding steady.
7. After confirming the direction of gate movement please check if the limit block fixed in good position
to avoid the motor run out of control due to failure.
Important Notes

EN
20
FUNCTION DIP SWITCH MODE
Limit mode
setting
Dip 1/OFF NC mode(Factory setting)
Dip 1/ON NO Mode
Limit switch direction
setting (J1)
Normal : Short circuit cap simultaneously No1 and No2 of J1 (Factory setting)
If motor system install at left of gate . Please adjust the J1 ,short the cap simultaneously No2 and No3
Infrared
mode set-
ting
Dip 2/OFF NC mode(Factory setting)
Dip 2/ON NO Mode
CAUTION If the gate meet obstacles during closing, It will auto stop and auto open. After The gate complete
open to its place, it will auto close again if the obstacle disappear within 2s, if not , it will not auto
close until to the obstacle disappear
Auto close
time
setting
Dip 3&4 all
in OFF
Auto close function disabled (Factory setting)
Dip 3/ON &
4/OFF
10 S
Dip 3&4 all
in ON
60 S
Dip 3/OFF
& 4/ON
30 S
CAUTION Auto close function activated after gate complete open to its place and stop by limit switch
Auto close
time setting
when
pedestrian
mode
activated
Dip 5&6 all
in OFF
Auto close function disabled(Factory setting)
Dip 5/ON &
6/OFF
5 S
Dip 5&6 all
in ON
30 S
Dip 5/OFF
& 6/ON
10 S
CAUTION 1.When the motor is running, the motor will stop immediately if triggers pedestrian mode
2.After triggering the pedestrian mode to open the gate for 6s, no mater it enter the countdown to close
the gate or stop status, If trigger again, the gate will close the gate immediately.
Condomi-
nium mode
setting
Dip 7 OFF Condominium mode disabled(factory setting)
Dip 7 ON Condominium mode activated
CAUTION When the gate is opening, trigger remote control and the start interface are invalid until the door is
opened.When the gate is closing, trigger remote control and the start interface , the gate will stop
to close and auto open until the opening limit is reached (the remote control and the start interface
are invalid when the gate is opening).
Remote
buttons
mode
Dip 8 OFF Single button control circularly,First button control gate open,stop, close, second
button use for pedestrian mode(factory setting)
Dip 8 ON
CAUTION Please choose the remote control mode firstly before remote control code clearning to control
board