CashConcepts LXD 50 User manual

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
CashConcepts LXD 50
User Manual

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Introduction
Many thanks that you have decided on the LXD 50. This banknote counting machine should simplify you the processing and
counting of bigger money amounts. Sorted banknotes can be counted by the different countable kinds and be checked for
overlooked other noted, as well as unsorted banknotes can be counted by their value and can be listed and checked at the same
time for counterfeit money. About the several sorting functions you have the possibility to sort the banknotes according to your
default. Moreover the reject pocket offers the possibility to check and count bigger amounts of banknotes without any stop
because of non-recognition of the security signs. The LXD 50 offers therefore in the office area for all supermarkets and retail
dealers, and also in the foremost front of the counterfeit money protection, e.g., at banks, used car traders or all other
companies where bigger cash amounts all at once change the owner.
Should you have questions to the LXD 50 banknote counting machine, we are available to you with pleasure.
Your Team of CashConcepts
Warning
General
Please pay attention that no foreign objects (e.g., coins, paper clips) fall in the machine, these can block the engines and the
sensitive sensors of the machine and damage or destroy them.
Please note that during the countable process no ties, hair or clothes in the bank note are drawn in to avoid injuries and
damages to the machine.
Please pay attention that none stuck, washed, strongly dirty or damaged banknotes is counted in the machine, these can
hook up in the machine and tear.
Please turn off the UV-detection or switch off the machine aground the UV radiation of the sensors.
Do not operate the machine, if smoke or strange smell is detected from the machine. In this case, please contact your local
distributor
Attention electricity
Use the device only with the provided net part.
Use no damaged or humid net parts or power supply lines.
Connect the stream supply not with humid hands.
During the change of the fuse the machine must be completely separated from the stream net to avoid an electric blow.
Maintenance
Always switch the power off during cleaning.
Clean the machine with a dry cloth.
Do not use wet or damp cloth or cleaning products.
Do not spill any liquid or spray chemicals over the equipment.
If any liquid is spilled on it, disconnect the power cable from the supply and contact your dealer.
Never disassemble the machine expect the trained person.
Be careful not to pinch your finger when closing the upper and rear cover
This manual is available in several languages. You can download them on www.cashconcepts.cc.

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Appearance
No.
Description
No.
Description
1
Hopper guide / Feeder
10
Opener rear cover
2
Adjustment for banknote pressure
11
ON / OFF switch
3
Display
12
Power connection
4
Panel
13
PC connection
5
Upper cover
14
Connection for external display /
Thermal printer
6
Button for opening the machine
(between Display and reject pocket)
15
Fuse
7
Reject pocket
16
Serial sticker
8
Lower cover
17
Update image
9
Stacker / Stacker wheels
18
Update main
Panel
Key
Description
Key
Description
0-9
Numeric key for batch value
9/Batch
ON/OFF batch
CUR
Change the currency
0/Add
ON/OFF add function
8/Save
Save settings in menu
Total
Shows report
5/Error
Shows errors from counting
7/Print
Print report
Mode
Switches counting mode
6/Setup
Entering user setting
START/STOP
Starts and stops counting
Clear
Clear the counting result
Green/Red LED
Banknote in stacker / reject
Display
No.
Description
No.
Description
1
Operation mode
6
Number of notes on reject
2
Currency
7
Number of notes on stacker
3
Batch
8
Total value
4
Speed
9
ADD function
5
Auto or manual start

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Self Diagnosis
After turning on the power of the machine, the self diagnosis will be done as follows:
Software loading
During software loading, each software
version will be displayed
After software loading successfully,
sensor and motor function will be
checked
If everything is OK, “Test OK” message
will shown up. However, if an error is
happened during initializing the related
message will shown up
Currency Mode
USD currency
Press CUR key and select US-Dollar ($).The machine can
count and recognize USD Dollar.
Please note standard software is Euro only. Other software are
optional available and may be deactivated in your machine.
Mix
Auto
0
100
$
100,000
P100
S1000
EURO currency
Press CUR key and select Euro (€).The machine can count
and recognize Euro Banknotes.
Mix
Auto
0
100
€
100,000
P100
S1000
LOCAL currency
Press CUR key and select the local currency (e.g. British
Pound).The machine can count and recognize the chosen
currency.
Please note standard software is Euro only. Other software are
optional available and may be deactivated in your machine.
Mix
Auto
0
100
GBP
100,000
P100
S1000

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Operating Mode
Count Mode
Press MODE key and select Count Mode. It counts all
banknotes without recognition and detection.
Count
Auto
100
P100
S1000
Mix Mode
Press MODE key and select Mix Mode. It counts all banknotes
of selected currency and add the value of the banknotes
Mix
Auto
0
100
$
100,000
P100
S1000
SP Mode
Press MODE key and select SP Mode. The machine will sort
out the same denomination as the first inserted note or the
pre-selected denomination. You can change the pre-selected
denomination by pressing the up and down ▲▼. The value of
the denomination will be display behind the mode.
↕SP
Auto
0
100
$
100,000
P100
S1000
V-SP Mode
Press MODE key and select V-SP Mode. The machine will
separate old and new version of a special type of banknotes.
This mode does not work in all currencies settings and may be
deactivated in your machine.
V-SP
Auto
0
100
$
100,000
P100
S1000
Face Mode
Press MODE key and select Face. The machine will separate
different sides of the banknotes depending on the first counted
banknote.
By using the ▲▼ keys you can also activate that different
denomination than the first banknote will be rejected.
↕Face
Auto
0
100
$
100,000
P100
S1000
Orient Mode
Press MODE key and select Orient Mode. The machine will
separate different directions of the banknotes depending on
the first counted banknote.
By using the ▲▼ keys you can also activate that different
denomination than the first banknote will be rejected.
↕Orient
Auto
0
100
$
100,000
P100
S1000

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Total & Error Display
Total Display
Press and hold down TOTAL key until TOTAL
VALUE LIST is shown.
It shows the denomination information of the
counted notes. (Number of denomination, value per
denomination, total number of banknotes and total
value of banknotes)
By pressing the TOTAL key again you can print out
the report on the optional thermal printer. By
pressing CLEAR you leave the report.
USD VALUE LIST
DENOM
UNIT
VALUE
USD 1
10
10
USD 2
4
8
USD 5
5
25
Total
19
43
Print (Key 7)
EXIT (C)
Error Display
Press and hold down 5/ERROR key until ERROR
REPORT is shown.
It displays the detailed information of rejected
banknotes.
ERROR REPORT
DBL
0
CHN
0
SKW
0
TIME
0
SLIP
0
HALF
0
IR
0
UV
0
Cleaning / Maintenance
The LXD 50 is equipped with a comprehensive error management to inform you about problems by the counting process and
the counterfeit money recognition and also for the soiling of sensors. Please note particular the tips to exclude to the cleaning of
the machine to avoid mistakes during the counting caused by dirtied sensors.
Cleaning of the sensors.
By the banknotes and by retreating dust it comes to depositions before the sensors of the machine. This pollution leads to
increased errors and non-recognitions of real banknotes.
Please clean at regular intervals the sensors of the LXD 50. Switch off the machine during the cleaning and
remove the net cable from the device.
With a soft paintbrush and cloth you can remove the coarse dust depositions from the sensors in the hopper and stacker are as
well as from the banknote conveyor wheels. To the cleaning of the counterfeit money sensors we recommend the additional
application of a non-inflammable air pressure spray around to remove also at inaccessible places dirt and particulate dust.
Please also remember of opening the back-sided flap (marked in BLUE on the next photos) of the sensor bank. Also open the
front side by pressing the unlock button (marked in RED on the next photos). Now you can clean the complete way the
banknotes pass from dust and dirt, as well as jammed notes. For closing the machine you have to lift the blockade (marked in
GREEN on the next photos)on the right side of the machine. Be careful not to pinch your finger. Should you have questions to
the right cleaning of the LXD 50, our service team is available to you of course with pleasure.

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Setup / User Mode
1. Press 6/SETUP key to enter the user mode.
2. Move to the required content by using the ▲▼keys. (*shows the actual selected content) and then press
START/STOP key to choose the content or press CLEAR key to exit the mode.
3. After choosing the content the target content will be highlighted in yellow color.
4. After changing the data press 8/SAVE key to save them, otherwise the data will remain unchanged.
No.
Contents
Description
Default Setting
1
Reject Size
Set Maximum Reject note capacity from 10 to 100
50
2
Ext –Device
Set the external Device between external display
and printer (refer to the detailed setting)
EXT-DISPLAY1
3
Density
Set the density level from -4 to 9 or AUTO for
count mode only. Lower value is less sensitive and
higher value is more sensitive setting.
AUTO
4
User ID
Set the USD ID shown in print
(refer to the detailed setting)
-----
5
Language
Set the language shown in display
ENGLISH
6
RTC
Set the Date and Time (refer to the detailed setting)
-----
7
Reject Disp.
Set the reject No. display function as ON or OFF
ON
8
CF Disp.
Set the CF display function as ON or OFF
OFF
9
Count
Set the counting start function as AUTO or
MANUAL
AUTO
10
Speed
Set the counting speed of the machine
1000
11
User I/F
Set the PC Interface NONE or USER 1
NONE
12
Counting Disp.
Set the denomination display function as ON or OFF
OFF

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Detailed setting in User Mode
EXT DEVICE SET
Display
EXT-Display I:
1-Line External Display ON or OFF
EXT-Display 2:
2-Line External Display ON or OFF
Printer Set: ON or OFF
Only if ON you can change Baud Rate,
Paper Size and Printing No.
Baud Rate: 9.600 ~ 115.200
Default Setting: 57.600
Paper Size: 2 or 3 inch
Default Setting: 2 inch
Print No.: 1 ~ 3 pcs
Default Setting: 1 pcs.
EXT DEVICE SET
1 EXT-DISPLAY 1:
ON
2 EXT-DISPLAY 2:
OFF
3 PRINTER:
OFF
4 BAUD RATE:
57.600
bps
5 PAPER SIZE:
2
inch
6 PRINTING No.:
1
pcs
UP[▲] DOWN [▼]
SEL [START/STOP]
SAVE [SAVE]
EXIT [CLEAR]
EXT DEVICE SET
1 EXT-DISPLAY 1:
ON
2 EXT-DISPLAY 2:
OFF
3 PRINTER:
ON
4 BAUD RATE:
57.600
bps
5 PAPER SIZE:
2
inch
6 PRINTING No.:
1
pcs
UP[▲] DOWN [▼]
SEL [START/STOP]
SAVE [SAVE]
EXIT [CLEAR]
The highlighted content can be changed by pressing MODE key and by the ▲▼ keys you can change the value. Press 8/SAVE
key to save the data before exit the setting.
USER ID
Display
The highlighted content can be
changed by pressing MODE key and
by the ▲▼ keys you can change the
value. Press 8/SAVE key to save the
data before exit the setting
EXT DEVICE SET
USER ID
1
2
3
4
5
……
A
B
C
D
E
……
SPACE [MODE]
DEL[CUR]
UP[▲] DOWN [▼]
SEL [START/STOP]
SAVE [SAVE]
EXIT [CLEAR]
RTC
Display
The highlighted content can be
changed by pressing MODE key and
by the ▲▼ keys you can change the
value. Press 8/SAVE key to save the
data before exit the setting
EXT DEVICE SET
04 : 15: 19
24 / 01 / 2011 TUE
UP[▲] DOWN [▼]
SEL [MODE]
SAVE [SAVE]
EXIT [CLEAR]

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Error Codes
Display
Cause of Error
Possible Solution
DBL
Double notes
Check the condition of rejected note as Double
Check the gap between Feed and Reverse Roller
CHN
Chain notes
Check the condition of rejected note as Chain
Check the gap between Feed and Reverse Roller
Check the condition of Encode Sensor in Service Mode
SKW
Skew notes
Check the condition of rejected note as Skew
Check the gap between Feed and Reverse Roller
TIME
Processing time error
Check the gap between Feed and Reverse Roller
Check the cable connection between Image and Main Board
SLIP
Slip feeding error
Check the gap between Feed and Reverse Roller
Check the condition of Rollers in feeding path
HALF
Half notes
Check the condition of rejected note as Half
Check the condition of Count Sensors in Service Mode
IR
IR error
Check the condition of rejected note
Restart counting operation
UV
UV error
HIS
HIS error
MG
MG error
LL
Length size of notes
SL
Width size of notes
IMG0
Image error
Check the condition of rejected note as Image
Check the gap between Feed and Reverse Roller
Clean CIS Sensor
IMG1
IMG2
DIF
Different notes
Check the image of notes
Accessories
Included
Optional
No.
Name
No.
Name
1
Power Cord
1
External Display
2
User Manual
2
Thermal Printer
Specifications
Subject
Technical information
Pockets
1 Stacker, 1 Reject
Counterfeit detection
UV, HIS, MG, IR
Adaptation currency
USD, EURO or Local Currency
Speed
1.200 Notes / Min. (Piece Count)
1.000 Notes / Min. (with Detection)
Hopper capacity
500 notes
Reject capacity
100 notes
Stacker capacity
300 notes
Power
AC 100~240 V 50/60 Hz.
Power consume
75W
Dimensions
284 (W) x 315 (D) x 277 (H) mm
Weight
Approx 13kg
LCD Size
3.2 Inch TFT
Mode
Count, Mix, Separate, V-SP, Orient, Face

CashConcepts Europe GmbH
Kemptener Straße 99 –D-88131 Lindau / Germany
Tel.: [phone] / Fax: [phone]
Email: [email protected] / Web: www.cce.tm
Contact
If it should once have problems with your LXD 50 which you can solve with the help of this manual, then you please get in
contact to us by email and describe the problem, we will get in contact to you as soon as possible with a proposal for solution
for the problem.
[email protected]
Please retain your purchase documents for warranty claims. Do not remove, cover, damage or modify in any
way the rating plate with serial number on the rear of the unit, otherwise you forfeit your warranty.