Cateye PADRONE DIGITAL CC-PA400B User manual

3
SET 4
1
5
2
Using the app
Using the unit
Appendix
Cover,
Introduction
CATEYE
PADRONE
DIGITAL
CYCLOCOMPUTER
CC-PA400B
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by CATEYE Co., Ltd. is under license. Other
trademarks and trade names are those of their respective owners.
1
This instruction manual is subject to be
changed without notice.
https://www.cateye.com/instruction/?id=CC-PA400B
Setting up the
PADRONE DIGITAL
Smartphone
PADRONE DIGITAL
Mounting
the PADRONE DIGITAL
Introduction
Starting measurement
Changing settings
Capabilities with a
smartphone
(Cateye Cycling™ app)
Warning / Caution
Product Warranty, etc.
Cateye Cycling™ iOS version

3
SET 4
1
5
2
Using the app
Using the unit
Appendix
Cover,
Introduction
2
The PADRONE DIGITAL is a cyclocomputer that uses with Bluetooth® sensors.
In addition to the included speed/cadence sensor, heart rate measurement can be added
by pairing with an optional heart rate sensor.
Mounting the PADRONE DIGITAL
• Mounting the bracket (Page 3)
• Mounting the speed/cadence sensor (ISC-12) (Page 5)
* For details about how to perform operations such as mounting CATEYE sensors and
pairing, see the sensor’s online manual (on our website).
Setting up the PADRONE DIGITAL
The first time that you use this product, perform the initial setup from the PADRONE
DIGITAL or from a Cateye Cycling™ app.
Use the method corresponding to your device to set up the PADRONE DIGITAL. You can
change the display of its measurement screen and its total distance value as necessary.
* If you have a smartphone, you can use the “Cateye Cycling™” smartphone app (download
for free) to easily set up the PADRONE DIGITAL.
• If you do not have a smartphone
1. Setup with the PADRONE DIGITAL (Page 9)
2. Changing settings (Page 21)
• If you have a smartphone
1. Setup with a Cateye Cycling™ app (Page 13)
2. Capabilities with a smartphone (Page 30)
Introduction

Cover,
Introduction
3
SET 4
5
2
Using the app
Using the unit
Appendix
1/6
1
3
• When mounting on handlebar
Mounting the bracket
The bracket can be mounted on either the stem or the handlebar.
1
Mounting the bracket
• When mounting on stem
Mounting the PADRONE DIGITAL
Cut
Cutting band after mounting
Caution!:
Cut the bracket band so
that cut end will not cause
injury.
Dial
Handlebar
Bracket band
Bracket
Bracket
rubber pad
Stem
Bracket band
Bracket
Bracket
rubber pad
Bracket band Bracket DialBracket rubber pad

Cover,
Introduction
3
SET 4
5
2
Using the app
Using the unit
Appendix
2/6
1
4
2
Attach/detach PADRONE DIGITAL
Mounting the PADRONE DIGITAL
Hold PADRONE DIGITAL.
Push out so that front lifts up.
Click

Cover,
Introduction
3
SET 4
5
2
Using the app
Using the unit
Appendix
3/6
1
5
• Mounting on top of chain stay
Mounting the speed/cadence sensor (ISC-12)
The speed (cadence) sensor can be mounted either on the top or bottom of the chain stay.
• Mounting on bottom of chain stay
Caution!:
If the speed (cadence) sensor is mounted on the bottom of the chain stay rather than
on the top, the adjustment range between the sensor and the magnet will be narrower.
* If using pedals with steel axles, the cadence magnet can be attached magnetically to the
pedal axle.
* For details about how to perform operations such as mounting CATEYE sensors and
pairing, see the sensor’s online manual (on our website).
* The following mounting procedure gives instructions for mounting on the top of the
chain stay.
Mounting the PADRONE DIGITAL
Cadence magnet
Cadence magnet
Speed (cadence)
sensor
Speed (cadence) sensor
Wheel magnet
Wheel magnet
Wheel magnet
Cadence magnet
Nylon tie (x5)
Sensor rubber pad
Speed/Cadence
sensor
(ISC-12)

Cover,
Introduction
3
SET 4
5
2
Using the app
Using the unit
Appendix
4/6
1
6
1
Temporarily attach the sensor to the left chain stay.
(1) Loosen the sensor screw using a Phillips screwdriver and check that the
sensor arm moves.
(2) Attach the sensor rubber pad to the sensor.
Sensor rubber pad
(3) Refer to the illustration and temporarily attach the sensor to the left chain stay
with nylon ties.
Caution!:
Do not fully tighten the nylon ties.
Once the nylon ties are fully tightened they cannot be removed.
Nylon tie
Sensor arm
Sensor screw
Left chain stay
Mounting the PADRONE DIGITAL

Cover,
Introduction
3
SET 4
5
2
Using the app
Using the unit
Appendix
5/6
1
7
2
Temporarily attach the magnet.
Nylon tie
Sensor zone
(CADENCE) side Sensor zone (SPEED) side
Cadence
magnet Spoke
Wheel magnetSensor zone (CADENCE)
Sensor zone (SPEED)
(1) Using a nylon tie, temporarily attach the cadence magnet to the inside of the
left crank arm so that it faces the cadence sensor zone.
* If using pedals with steel axles, the cadence magnet can be attached
magnetically to the pedal axle. In this case, remove the adhesive tape from
the magnet and do not use the nylon tie.
(2) Rotate the sensor arm and temporarily attach the wheel magnet to a spoke
facing the speed sensor zone.
* Reposition the sensor and the magnets if both magnets (speed and cadence)
cannot pass through their respective sensor zones.
Mounting the PADRONE DIGITAL

Cover,
Introduction
3
SET 4
5
2
Using the app
Using the unit
Appendix
6/6
1
8
3
Adjust the gap between the sensor zone and the magnet.
(1) Tilt the sensor so that the gap between the cadence magnet and the cadence
sensor zone is approximately 3 mm, then fasten the sensor securely with
nylon ties. 3 mm
Cadence magnet
(2) Rotate the sensor arm so that the gap between the wheel magnet and the
speed sensor zone is approximately 3 mm, then tighten the sensor screw
securely. 3 mm
3 mm
Sensor screw
Wheel magnet
4
Secure all parts.
Securely tighten the sensor’s nylon ties, the sensor screw, the wheel magnet, and
the cadence magnet so that they do not move, and then check that these items are
not loose.
Trim off the excess nylon tie.
Mounting the PADRONE DIGITAL

Cover,
Introduction
3
SET 4
1
5
Appendix
Unit
1/4
2
9
Setting up the PADRONE DIGITAL
Setup with the PADRONE DIGITAL
If using a smartphone, see “Setup with a Cateye Cycling™ app” (Page 13) to set
up the device.
* Check the locations of the buttons on the PADRONE DIGITAL before starting setup.
AC
MODE
MENU
Battery case cover
Dot section
Short press
Long press
(2 sec.)
MODE
MODE
Remove the battery insulation sheet from the PADRONE DIGITAL.
After removing the battery insulation sheet, return
the battery cover to its previous location.
Insulation sheet
COIN
Open
Close
1
Format (initialize) the unit.
While holding down MENU on the back of the PADRONE DIGITAL, press and
release the AC button.
ACAC MENUMENU ACAC MENUMENUMENUMENU MENUMENU
1 2 3
The whole display turns on, and then the smartphone search
screen is displayed.
* All data is deleted and the unit is reset to the factory
default settings.
* If the smartphone search screen is not displayed, the unit
could not be formatted. Try to perform the operation again.
MENU

Cover,
Introduction
3
SET 4
1
5
Appendix
Unit
2/4
2
10
2
Select the measurement unit.
Press MODE to select “km/h” or “mph”.
After selecting a value, press MENU to proceed
to the next step.
3
Pair with a sensor.
Caution!:
• To use the PADRONE DIGITAL, you have to pair it with a sensor that
supports the Bluetooth® standard.
• Avoid pairing sensors at a race venue or in similar locations where there
are a lot of other users. Doing so may cause the PADRONE DIGITAL to be
paired with another device.
The unit switches to the pairing standby screen and Pr
flashes on the screen.
Included sensor Activating the sensor Display
Speed/Cadence
sensor (ISC-12)
Move the magnet through the sensor zone
several times. (Within 3 mm) ISC
* For the CATEYE sensor signal activation procedure, refer to the sensor’s online
manual.
Once pairing is complete, the name of the sensor is shown in the upper display.
* When pairing a sensor with the PADRONE DIGITAL, a “C” is displayed after the
sensor name.
4
To pair multiple sensors, hold down MODE to return to the
pairing standby screen.
Repeat step 3 to pair all the sensors that you intend to use.
* To add heart rate measurement, perform pairing with the
heart rate sensor here.
Once you are finished pairing sensors with the unit, press
MENU to proceed to the next step.
Setting up the PADRONE DIGITAL
MODE
MENU
Re-verify
(press and hold)
Confirm
MENU
MODE
km/h ↔mph
Confirm